Infinite Boot Loop, Even Safe Mode Won't Work
Aug 6, 2007
I was incredibly bored and I downloaded an old DOS VGA version of The Oregon Trail from the-underdogs. I used VDMsound to run it, and everything seemed to work alright until i got sick of the game and tried to quit. It locked up, i used ctrl-alt-del a few times, got impatient and stupidly switched off the computer just as i was being dumped back to windows. When i turned the computer back on, i was given the "safe mode" prompt, so i chose to start in safe mode. It then showed that list of system files(?) it was loading until it gets to "d347bus.sys" and asks if i want to press escape to skip loading it. Regardless of whether i press esc or not, it moves on to "SPTD.sys" and asks the same question. After i press escape (or not), i get a black screen, then the computer restarts again back to the safe mode prompt. If i try to "start windows normally" i get to the Windows XP loading screen, the progress bar moves a bit then the whole thing restarts again. Safe mode with command prompt, safe mode with networking, last known good configuration, none of these work, they all result in this maddening infinite loop.
View 2 Replies
ADVERTISEMENT
Mar 9, 2010
My desktop is stuck on an infinite startup loop, I can see the standards Windows starting screen then there is a quick BSOD flash and the computer restarts and does the same thing - lucky I have a spare old laptop which will allow me to jump onto this site. Safe mode options do not work I tried the Windows recovery console - typing 'R' booting from the CD but then I get stuck at the console black screen not knowing what DOS commands I should be pushing. I tried goign the other way and choosing to install XP but then I get a message saying C: isn;t configured and will need to format to continue.
View 4 Replies
View Related
Aug 4, 2006
I was attempting to boot into safe mode through the BOOT.INI /SAFEBOOT function in MSCONFIG. After restarting to boot into safe mode, my computer would restart ten seconds into the login screen. This happens every single time and I cannot get back into Windows to uncheck the /SAFEBOOT box. The computer that I am typing on right now allows the user to choose the boot method before entering Windows. It has an old ASUS board and is running Windows XP Pro w/ SP2.
My primary computer (the one that is restarting) has an ASUS A8N-E and is running Windows XP Home w/ SP2, latest updates. Is there anything I can press (one of the F keys, perhaps?) that will prompt me to choose the booting method? Safe mode has restarted on me before, but not like this. I tried setting the motherboard to defualts in my BIOS, but that was just a stab in the dark, as I don't see what that has to do with this problem. I am thinking about setting my motherboard to defualts by opening up the case, etc. but I don't think that will do anything.
View 2 Replies
View Related
Aug 21, 2007
I'm working on an IBM ThinkCenter Desktop PC.On bootup, it goes through the IBM logo and then the Windows logo flashes quickly and then is gone and then the Safe Mode screen appears. No matter which option I choose from the Safe Mode screen, the result is the same: The Windows logo flashes quickly and then the system reboots, and then the IBM logo and then the Safe Mode Screen.I have tried running the repair module from an o/s disk I have here, but when I get to the c: prompt and type "dir" it says "error occurred during directory enumeration".There is only one partition.I have a copy of UBCD4WIN, if that would be helpful in diagnosing the problem.I do not have the o/s disk that belongs to this computer.
View 2 Replies
View Related
Aug 18, 2007
I changed the BOOT.INI section of msconfig to boot windows in Safemode. Upon getting in Safemode, the computer finally recognized USB devices and the CD drive again (wasn't doing so in normal mode). So, I insert a Windows XP disc, used the Advanced install mode (the one that overwrites the previous installation of Windows), and everything seemed to be going great.
However, the machine restarts and tells me this "Windows XP Setup cannot run under Safemode. Setup will restart now." and has an OK button. I click it, thinking it's going to boot into normal mode. Well, it doesn't. It boots up again, says the same thing.I click OK.Restart.Again.OK.On and on into infinity.
View 14 Replies
View Related
Jan 28, 2007
I have a machine running win xp home edition SP2 that will not load windows up unless I do it by way of safe mode. It goes to the black xp screen and hangs up there. I did a system restore to an earlier date in safe mode but when it resarted i got the same results. Is this a symtom of a bad CMOS battery? The system has been running good for 3 years and this just started today.
View 8 Replies
View Related
Nov 23, 2006
pc wont boot. its a sata hard disk which is detected upon boot. however i dont even get the windows splash screen. in the bios - the hd doesnt show up. safe mode doesnt work neither does last known good settings. i put the xp disk in and attempted to do an (install followed by a repair ) rather than system console. nothing works because the xp disk claims no hard drive exists. is it cos its serial ata. im not exactly sure if its got raid setup etc although i do possibly remeber a viaraidtool popup that might have come up on the odd times ive been over and used my dads pc to educate him on eBay. :-) anybody got an idea. sorry i dont have specs.
View 8 Replies
View Related
Oct 9, 2009
Powers on to the normal blue screen. Black screen comes up that says We apologize for the inconvience...etc. etc. windows did not shut down normally and gives the option for last know good configeration, start windows normally, safe mode, etc. Tried them all and it just goes back to the normal blue screen and back to We apologize for the inconvience. F10 system recovery does the same thing.I would like to be able to fix this and not lose any of the information I have on my hard drive. I did a total back-up about 7 months ago (13 DVDs worth) and do have some backup through Norton 360
View 11 Replies
View Related
Mar 27, 2008
A family members sony vaio will not boot up, the computer doesnt load windows XP (The windows XP loading screen appears but will then goes blank and reboots automatically.) When the computer first turns on a blank screen appears with text saying "we're sorry for the inconvienice, etc..." then has a 30 second timer for which option i would like to choose.These are my options below (which none work).
It doesnt work on Safe Mode, Safe Mode (Networking), Safe Mode (Command Prompt) or even the "last known to work configurations". Im totally lost on what i can do from here. I need assistence people!!
View 11 Replies
View Related
Aug 8, 2008
I had a problem with windows xp rebooting after everytime during the loading screen. I tried doing chkdsk /k with no use and then I tried to repair the installation. Now i can't finish the setup and can't access safe mode because it says. Windows XP setup can't run in safe mode.
View 1 Replies
View Related
Mar 21, 2006
I am not really a computer whizzkid but am not afraid to give most things a go ever since powering down for a holiday my xp start up is in a loop. Clicking f8 and trying to access safe mode doesn't work either. Have tried "last known settings" but still no luck although it does get me a bit further but then I get the message ODBC32.dll was not found in the winlogon.exe box. Then MPR.dll was not found message appears. Is there anyway I can access the c prompt and do anything or should I have a restore disc somewhere that I haven't found supplied when I purchased the PC
View 5 Replies
View Related
Sep 8, 2006
My computer is stuck in what i think of as a restart loop. After powering on, windows xp screen appears (w/moving bar at bottom) sits there for about 7-10 sec then screen goes blank and about 3 sec later it restarts. Windows login does not appear. It will continously loop thru this process. At first Safe mode only started with out networking options. But now I can't start in safe mode at all it just reboots the computer after the scrolling screen of items being started. I am not sure what this could be, and have no idea how to get at least safe mode working.
View 3 Replies
View Related
Sep 9, 2002
The best solution to most issues with looping is POWER SUPPLY. Due to the huge amount of resources that video cards, sound cards, larger cpu's, they suck your power supply to the point that application cant perform. In turn it causes lockup, reboot and boot to desk top.A lot of resellers are only slapping in a 300watt power supply in newer systems. That doesn't work, you need at least a 400watt or greater. You need at least 450watt POWER SUPPLY. Take my word on it.This is the biggest issue i have studied on the net and in my lab for 1 1/2 years now. So many people have taken components back to the stores had them tested, to find out there is nothing wrong with them and go around shaking there heads in wonderment, without even considering power supply.
View 9 Replies
View Related
Nov 18, 2007
I have been trying to play Half-Life 2, but at certain loading screens, it throws me the nv4_disp infinite loop error.
View 6 Replies
View Related
Dec 23, 2008
Computer is not is a very slight increase in memory voltage. i have tried basic standard voltage setting as well as slightly higher settings. A game, or anything using 3d or direct x causes the problem. at first i got a hang and total system freeze. had no error or bsod.specifically the game was FSX sp2. also occured with command and conquer red alert 3, and sins of a solar empire. additionaly 3dmark06 did the same thing. specifically the games or program would load fine but once it started the first screen or opening graphic it just freezes the entire system. i have to reboot via reset button. and windows load just fine. only 3d programs or games does this. no bsod until last night i finally got the nv4_disp infinite loop error.
View 6 Replies
View Related
Jan 5, 2009
Ok, I have solved "MY" nv4 loop error.It is not a software fix however. After I and most people have tried every fix out there, I decided to go to the root of the problem. The memory. I ran boot up with each DIMM alone. I use 3 1gb OCZ 6400's . 2 of these DIMM's ran any program that crashed before with no problem, only 1 did not. I ran the 2 DIMM's together and no more error. I have heard that there is an issue with the 680i motherboards giving incorrect voltage to memory or that it reads incorrect voltage . In either case on memory module is bad. While I consider this a final troubleshoot victory , it isnt cheap. But none the less im happy with the outcome.
View 1 Replies
View Related
Dec 7, 2004
I decided to do a fresh install of Windows XP Home. So, I put in the WinXP Install CD and set the BIOS to boot to CD. I deleted the partition (only one on my 60GB hard disk), created a new one, and formatted it NTFS - all by following directions in the Windows XP Setup program on the CD. Then I chose to setup WinXP on that formatted partition. The CD copies a bunch of files over, then tells me to remove disks and restart the computer. So, I do. I boots to the hard drive and gives me the "Windows XP Home Edition" screen with the moving green bar at the bottom while it's loading. Then it quickly goes to a rather blank screen that says "Setup is being restarted," strange moving lines cover the screen, and the computer restarts. It then does the same thing over, and over, and over again. I've tried repartitioning and restarting the setup process several times, trying every available option but after Windows Setup restarts the first time, it gets into that infinite loop of never proceeding to the next step of setup.
View 14 Replies
View Related
Apr 12, 2006
I have an Asus W3H00V (which came with the Mobility Radeon X600) that I use for word processing, internet, and watching videos, though never really use it for gaming. After about a couple of months of use, my laptop suddenly always hangs with a blue screen popping up saying that there's an infinite loop problem that's caused by the file ati2dvag.dll, especially when watching videos. I've tried uninstalling and installing Windows XP (w/ sp2) four times and also uninstalling and installing the ATI drivers that came with my computer numerous times but nothing seems to work. I can't get any work done on my computer because an error window also always pop up and hangs my computer very frequently. I've tried searching for solutions in the internet but none seems to work.
View 2 Replies
View Related
Feb 22, 2008
I have a computer that will not boot up except for in safe mode, probably due to a virus. When I attempt to install the latest Ad-Aware, I get the following message:"Windows Installer: The system administrator has set policies to prevent this installation" I am currently logged in as administrator
View 2 Replies
View Related
Nov 10, 2009
I keep getting the error jCarousel: No width/height set for items. This will cause an infinite loop. Aborting how do i get rid of this i hit ok and it comes back.
View 1 Replies
View Related
Sep 15, 2007
I don't really know where i should start so.well earlier today i installed a second hd in my computer to pull so files off of it for my sister and my mom, but when i got it working it said accsess was denied to there stuff i went on my moms computer to check if i hade already backed up there stuff of the old comp, so i go into her document to see if i could find the old documents and when i start scrolling through them the window freezes...so i leave it for a minute and while i'm waiting i close some other programs one of which was mozilla which was also frozen.I go back to the my document window and its still frozen.
I try to close it and of course its not responding so i click end now and it made the every thing disappear like the task bar and all the icons on the desktop are missing...so i wait and see if any thing will reappear and nothing does so i restart it and it starts booting up..the windows logo comes up and the little bars only gets half way across then it restarts and brings me to that menu where you can choose save mode or start normally and all that and no matter what i pick the comp just restarts and bring me back to the menu.
View 1 Replies
View Related
Mar 3, 2007
my computer hasnt been able to go into safe mode the last two times some bad thing has happened to it. i can easily get into the menu where you have to select how you want to start up, but when i select safe mode, it just sends a wall of text down, and stops at "mup.sys" each time. from there i have to reboot to get it to do anything.now my main problem is that i disabled the graphics card i have installed in the pci and the motherboards default graphics card (i wanted to use the original one so i could transfer my graphics card to a different computer), so i cant really do much about getting into windows to change that, with out being able to run in safe mode.
View 2 Replies
View Related
May 3, 2005
I went into MSCONFIG and checked the box to go into safe mode so i could run some virus scans and adware scans and stuff like that. Now when it gets to the desktop it has the window that says Loading Windows and then after like 2-3 min. it says password is incorrect and that i should retype it and becarefull of caps lock and stuff like that. The thing is don't have a password. It does this when i boot normally too but it lets me hit ok and hit Cancel without a password entered.
All of a sudden it tries logging me in automatically when I start up but the thing is i dont need to log in. So I try to go back into normal mode and Ican't. I hit F8 during startup and went to the Boot Normally option but it still does to safe mode. What do I do? How do I log on or how do I get rid of this password thing? One more thing, the window that tells me the password is wrong has an OK box but theres no mouse on the screen for me to click it and I can't use the keyboard to select it.
View 14 Replies
View Related
May 3, 2007
In device manage it has exclamation by it i uninstalled but if i do add hardware its located w/ exclamation by itif i uninstall an restart its back with exclamation dont work in safe mode works be4 boot when i type in password its disabled on boot.
View 1 Replies
View Related
Sep 22, 2004
My computer starts up normally.It always just autologs on since I'm the only one using my windows xp computer. However, before anything can be displayed it immediatley logs off to the logon screen. I click my username and start the login process (i have no password and before even switching to my wallpaper or anything it says stuff like logging out and saving your settings.
I tried booting in safe mode too and the same infinite logon loop occured to, even with the default administrator account. The last thing I remember doing before this happened is I was playing City of Heroes when it crashed forcing me to restart my computer. This happens occasionally in certain programs but I've never had anything like this happen before. I tried unplugging my keyboard, mouse, usb devices, ethernet cable, no luck. Intel Pentium 4 1.7 ghz Geforce 5600 FX 256 mb windows xp home service pack 1, in case any of that matters
View 10 Replies
View Related
Mar 20, 2007
I have a dual boot linux/xp system.I was looking at partitions - just listing them - in linux, and now win xp won't come up in normal mode. It will come up in safe mode, however. Can you help me get my "normal mode" back?When the horizontal moving bar comes up in normal mode, it just goes on forever. I see the disk light go on for about 8 cycles of the bar. It usually runs 11 cycles before giving me the user selection screen. Now the disk light goes out after cycle 8, and the bar keeps going. I waited 32 cycles before giving up.
View 1 Replies
View Related
Sep 29, 2007
Windows XP Home : My desktop boots only in safe mode and system restore fails. Last known good configuration doesn't work too. Normal boot falls in a restart loop. Can somebody help, please ? Problem created by malware (trojans,worms,etc).I use Avast antivirus.
View 8 Replies
View Related
Sep 24, 2009
I tried System Restore a week ago, but it didn't work. It ran but at the end I got the error message that it didn't complete and couldn't restore to the earlier point. It displayed the red "X." I deleted all of the restore points and set the amount of store to the maximum and set a new restore point. Still it didn't complete. I also ran Malwarebytes - it couldn't find any issues.I tried it in Safe Mode and it worked - it set the new point and renamed three files - two of them were Norton files, the third I didn't recognize. I set a new point and again it DID NOT COMPLETE - I got the same error message!
View 3 Replies
View Related
Sep 15, 2007
I bought a new cpu awhile ago. When I moved my old cpu to my other desk and restarted it, it would only let me start in safe mode. It was working fine prior to this. I tried system restore to many differnt days, but nothing would work. I think I probably need to reinstall windows, but before I do, I was wondering if there is anything else I can try.
View 14 Replies
View Related
Nov 23, 2009
I have a Windows XP Professional Edition and i incurred a spyware virus on my PC, so i made a dumb decision by running MSCONFIG and changing my SAFEBOOT option, I did this because previously I couldn't even get into Safe Mode, it would load the files on the screen.
View 1 Replies
View Related
Jul 25, 2008
Recently I was playing a game when my computer froze up, when I restarted it, it froze every time on the Windows XP bootscreen. It boots fine in Safe mode with networking. (I'm typing this post on this computer)
View 2 Replies
View Related
