Windows 7 Won't Boot / System Repair / Restore / Safe Mode Won't Work

Jan 1, 2013

I have recently installed windows ultimate x64 on my computer.i have an asus p6t deluxe v2 mobo, i7-960 cpu and a wd velociraptor hdd. The install went ok, I even managed to restart my computer a few times after but after windows updates installed it won't boot. I tried to boot into safe mode, restore from the installer, and repair, none worked. After startup repair it says: "a patch is preventing the system from starting" and I get a 0x1f error code.(Preventing windows from downloading any updates didn't work either)

View 9 Replies


ADVERTISEMENT

Dell XPS Crashes .System Repair,system Restore ,safe Mode Don't Work

Mar 8, 2012

I am having the following system configuration

XPS L401X Base
Genuine Windows(R) 7 Home Premium 64bit (English)
Intel(R) Core(TM) i7-740QM Processor
6GB 1333MHz DDR3 SDRAM (1 x 2GB + 1 x 4GB)
640GB 7200RPM Hard Drive

Lately whenever i try to start my computer it pass the Dell Bios and then directly goes to the screen which states
Repair your system or Start windows normally When i chose repair system , it start downloading windows files and then launch the windows , but hung up at the sky blue login window with only movable cusor . When i choose to start windows normally it gives me BSOD momentarly ( hard to see the message) and then restarts again . i tried with the advanced boot up options like
repair my computer , all safe modes , restore to last good configuration but it does the same and hangs at windows loging sky blue window .I Tried to run the Dell PSA+ Diagnostic and it returns with 2000-0146 error . As per the Dell online solutions for this type of error ,I tried to reinstall the Hard disk but the problem still exist.

View 3 Replies View Related

System Repair And Safe Mode Won't Work

Dec 17, 2010

my laptop starts up as the "windows did not shut down properly" screen where I can start windows normal to do repair. When I start windows normally it sends me to the repair screen. And when I select system repair it just freezes at a light blue and geen screen and the only thing showing is my cursor. Ive tried to run the system in safe mode but it freezes at classpnp.sys, and eventually sends me back to the repair screen that is frozen. I don't believe I have my windows 7 installation disk for my laptop so that is out of the equation.

My brother was using my computer and said it was updating when this happened so Im not sure what caused all this.

View 9 Replies View Related

System Repair/safe Mode Wont Work?

Mar 9, 2012

The other day i found some ram and decided to try and see if it worked in my Dell desktop computer, when i turned it on it said i couldnt mix different types so i took it out and turned it off, i diddnt even go on it.Today i turned it on and it got to the windows 7 logo and it restarted and said windows failed to start, launch startup repair or start normally. I clicked startup repair but it woulnt work, i tried restoring to an earlier date but that wouldnt work either. I tried safe mode but when it gets to loading it restarts and just goes round in circles.

View 6 Replies View Related

Restore System To Boot Automatically Without Going Into Safe Mode?

Sep 21, 2012

After a power outage, my windows 7 will not boot without going into safe mode.How can I restore my system to boot automatically without going into safe mode.

View 1 Replies View Related

Startup Repair Loop, Safe Mode Won't Work?

Feb 13, 2011

So I was using a program called TuneUp Utilities, and I used this function called the Disk Doctor to check for errors in my computer.While it was checking for errors, my computer shut down automatically and when I started it up again a black screen appears giving me the option to either load Startup Repair or Start Windows Normally. When I start Windows Normally, everything goes fine until I see the cursor. Nothing happens and then the computer restarts on it's own. I've even tried disabling restart on system failure but when I did that the computer just stayed at a dark screen until I restarted it.When I load Startup Repair, it searches for problems for like 5 minutes and then says it can't be automatically fixed. It says to remove all USB cables and everything (which I did but had no effect) and lets me have advanced recovery options.When I load advanced recovery options, all that appears is Startup Repair again.When I press F8 and do a Safe Mode, it starts up normally but once I see the mouse cursor the computer restarts.

View 5 Replies View Related

Windows 7 Safe Mode Boot Redirecting To Startup Repair

Dec 7, 2012

Earlier today I tripped over a headphone cord and it flung my computer off my desk. I have an HP omni PC. It's the kind that had the computer and the monitor built together. I picked it back up off the floor. The power cord came out on impact. I set everything back up and was relived to hear it turn on. I selected start windows normally (win 7 64 bit) and it sat at starting windows forever. I eventually manually shutdown the computer. I powered back on and I got an option to start windows normally or use startup repair.

I thought it would be a good idea to go into startup repair. It just sat at the light blue screen with the large white mouse sitting there. Nothing happened. Nothing appeared on screen. I turned off the computer again and am just leaving it there for now. I am worried that the hard drive may have been disconnected from the fall and that's why windows won't start. Or maybe the hard drive was damaged. I tried doing a safe mode boot but it redirected me to startup repair.

View 17 Replies View Related

Windows 7 Update Froze - Go To Safe Mode And No System Restore Back Up

Feb 14, 2013

On this recent windows update, 2/14/13, my computer froze on the "Preparing to configure windows" screen for several hours. I rebooted normally and the screen went to "configuring updates" and stuck at 67% for about an hour. I got frustrated with it and rebooted to safe mode to see if I could do a system restore and when I did it said there was no restore point back up! So I rebooted normally and now it is still just sitting on the "Preparing to Configure Windows" screen with the circle spinning. I am using Windows 7 Ultimate on a Dell Dimension 2400.

View 1 Replies View Related

Turn System Restore On, On Safe Mode?

Jan 13, 2013

I'm currently using a windows 7 computer and am having trouble accessing system restore. As I start up the computer normally, I make it past the login screen to the main screen, and it freezes after a few seconds each time. Going on safe mode instead, I went to system restore only to find that is was turned off as well my network connections

View 2 Replies View Related

Mouse Only Works In Safe Mode After System Restore

Oct 26, 2012

I ran a complete system recovery and now start up freezes. Seems mouse etc work perfectly fine in safe mode.

View 3 Replies View Related

64bit Laptop Crashed And Won't Start On Safe Mode, System Repair Failed?

Jul 17, 2012

i just crashed som1 64 bit lennovo laptop while i opperate a 32 bit pc dont have any windows system with me,it wont start on safe mode,and system repair has failed many times.the laptop was running on low battry and it shut itself,when i tryed to reboot it,it automaticly went to system repair which failed

View 2 Replies View Related

Using The Repair Disk When System Restore Doesn't Work

Jan 1, 2013

I have never had the need t use this disk till now but as I am getting problems starting up I tried System Restore and it didn't work (I have tried 2 restore points).Can I use the repair disk that I created on my HP desktop to mend the system or to restore it to an earlier time ? When I open the repair disk on the computer it just shows a couple of folders (boot ,sources as well as a file called bootmgr but I can't see a hrep file to let me know what I can do...

View 1 Replies View Related

Undo Or Recover Lost Files From System Restore In SAFE MODE?

Oct 27, 2011

I am familiar with System Restore, selecting earlier times, and the often-available option of undoing a System Restore. But I found out (too late) that according to Microsoft, System Restore done in Safe Mode is not able to be undone.I lost 1,000's of photos doing the system restore, now the only restore point option visible is what I believe to be the new one after I did the restore. Prior to me doing the System Restore, there were a number of times from me to choose from, I just chose one that was 10 days ago. Is there any software, method, or hack that I can use or do to recover the thousands of photos that were on my desktop and that were in folders on my desktop? It's a 1 TB HD?

View 1 Replies View Related

Can't Boot Windows 7 In Normal Mode After System Restore

Dec 10, 2012

I've just ran a full system restore on my niece's Dell Inspiron N5030 which runs Windows 7. After the restore the laptop restarted and went into the setup screen... then it tells me it's unable to continue the setup whilst in safe mode and asks me to restart...thus the loop continues.how to start in normal mode and continue the setup?I've tried going to the black boot screen which has a variety of options including "Start Windows Normally" but none of these worked.

View 10 Replies View Related

System Stuck In Boot Loop In Safe Mode

Jul 23, 2012

My system is stuck in a boot loop while booting in safe mode,I was updating the drivers on my video card. I used driver cleaner pro to remove my old drivers. I then used msconfig to boot in safe mode with the minimal option selected. When the computer reboots I get to the screen to type in my password for 5 seconds an the computer reboots itself.

View 5 Replies View Related

Laptop Won't Boot Up - Startup Repair And System Restore / None Will Finish

Oct 21, 2012

My Sony vaio just turned off last week and wont boot up. It turns on an flashes Sony vaio but that's all. I made a recovery disk and I can get into bios so I tried booting from internal disk and tried startup repair got nothing, tried system restore for every restore point and none will finish. Took each piece of ram out an tried starting it up to see if bad ram was the problem and it starts the same way. I also tried the restore from previous image but I have no image. So I don't know what else to try. Windows 7

View 15 Replies View Related

[DRIVERS] Computer Will Not Boot Normally, System Repair And Restore Failed

Jan 4, 2013

A few days ago, I went to turn on my computer and it just gave me a black screen after the "Starting Windows" screen. I attempted to use System Repair, which failed. It said there was an unspecified error possibly caused by a change in system configuration. I have not changed anything on my computer, for the record, between the last time it worked and now. My husband said it downloaded updates, which would explain why it was off in the first place instead of just being on stand-by. Anyway, I then tried System Restore, which also failed. I can get it to start in Safe Mode with Networking, but it seems that everything I try to run to figure out what the problem is, is saying it can't find the problem. I enabled bootlogging and found this...

Did not load driver @nettun.inf,%isatap.displayname%;Microsoft ISATAP Adapter
Did not load driver @nettun.inf,%isatap.displayname%;Microsoft ISATAP Adapter
Did not load driver @nettun.inf,%teredo.displayname%;Microsoft Teredo Tunneling Adapter
Did not load driver @hal.inf,%acpi_amd64.devicedesc%;ACPI x64-based PC
Did not load driver @battery.inf,%*compbatt.devicedesc%;Microsoft Composite Battery
Did not load driver @netavpna.inf,%mp-agilevpn-dispname%;WAN Miniport (IKEv2)

[code]....

View 3 Replies View Related

When Go To Safe Mode And Hit Repair Computer / Have To Use A Dvd And Hit Repair

Dec 2, 2012

when I go to safe mode and hit repair computer they say I have to use a dvd and hit repair. my dvd does not have repair on it I have trouble with startup I do not know how to use the dvd if it has no repair listed

View 9 Replies View Related

Cannot Access Safe Mode But Can Boot In Safe Mode With Networking?

Jun 3, 2012

After attempting to start my Laptop in Safe Mode, it loaded drivers normally only to crash a few seconds later. A prompt message appears but is impossible to read because Windows immediately reboots upon showing the prompt.

View 1 Replies View Related

Safe Mode Or Regular Mode Wont Work For Blue Screen Of Death?

Nov 25, 2012

i recently ran into a problem with starting up my computer. I have the blue screen of death. I've tried safe mode. It won't work. I would click safe mode it would load and then go back to the blue screen. I have a lenovo laptop and I'm not trying to pay 150-200 for it!

View 3 Replies View Related

Windows 7 Safe Mode Crashes - Startup Cannot Repair Computer Automatically

May 28, 2011

I recently got a virus 2 days ago. It disable my possibilities from accessing any program or internet. I made a mistake by downloading a windows something ware to boot up security. It then crash...so I went to task manager didnt work, which i then went to search and entered msconfig. I then chose safe mode in minimal services. It then says loading files. U see a black screen with thite letters of the files being loaded. Then u see ur mouse cursor, and then it boots up again and same process. So I tried launch startup repair, it launches a repair, but it says it startup cannot repair this computer automactically. I then result into going to tapping f8..it goes to the screen of advanced options. Problem is if i try safe mode it will crash. I dont have a backup, and i dont want to lose my movies of over 700 gigs.

View 5 Replies View Related

Windows Won't Load In Safe Mode Or Restore

Sep 24, 2012

I have a Sony Vaio which runs on windows 7 (don't know if it's 32 or 64?). I don't have any back up discs.

Computer started doing windows updates, when I turned the laptop on the next day it won't boot up normally or in safe mode. If I click on repair computer it scans and goes through the process but in the end it just takes me back to the same screen. I've tried to restore and I have several points come up in the list but it says beside them enable system protection for this (C Drive).

The only option I have is to put it back to factory settings which I would really like to avoid as I don't want to loose all my files. I have some of them on USB but not all.

View 3 Replies View Related

Startup Repair Runs, Can't Use Pc, No Safe Mode

Mar 10, 2012

every time i turn on my computer, I first get a message from AMI - "SATA 1:S.M.A.R.T. Status BAD". When I press F1 to continue, it progresses normally, until recently when i got "windows is loading files" then "startup repair" instead. Startup Repair searches, then finds a hard disk problem which it cant fix, and I can choose to reboot or try "advanced options"I've already tried safe mode, same thing happens.I've looked around, still not sure how to proceed - what caused this and can it be fixed without replacing my hardware?

View 2 Replies View Related

Windows 7 Won't Open; Safe Mode Won't Work?

Jul 8, 2012

When Windows looks like it is starting, the "Windows is loading files..." message comes up. It then goes into Startup Repair, which either can't detect problem or "Startup Repair cannot repair this computer automatically". I have tried pressing F8 for the safe mode menu, but none of the options there work either as selecting any of them just ends up in Startup Repair again. Sadly I have no system restore point or system image to reload. I have run the Windows Memory Diagnostic, which found no problems. I know that reloading Windows is almost certain to fix this problem, but I have a handful of files that I really, really don't want to lose by doing this. Is there any way that I can save my files?

View 3 Replies View Related

Cannot Run In Safe Mode And Any Start Up Repair Attempts Have Failed

Jan 24, 2012

Have an Advent laptop here, BSODing when booting with the error message above.Cannot run in safe mode and any start up repair attempts have failed.I have run disk checks both in the Windows start up tool and in Linux and they both say no problems but when I try a system restore it says there is one. Here is the .dmp file and the laptops specs.I also ran sfc /scannow but everytime I do I get a message saying there is a repari waiting for me to restart the laptop and that's all I ever get.[code]

View 9 Replies View Related

Windows 7 Won't Startup, System Repair And System Restore Failed?

Feb 15, 2013

Living is south FL can be a bitch when the rains come as there often is a ton of accompanying lightening that plays havoc with the electrical system, even though I have surge protectors inside and outside the house. We just had some very heavy rains with lightening and my computer shut down several times, but I could restart it each time...except for the last time when Windows wouldn't startup. At that point, Start Up Repair came into play. Although I routinely backup on an external drive, of course I never did it this month-DUH!Results from SUR were error free (error code=0x0) on all the parameters tested, however there were the following error codes reported:"Unspecified change to the system configuration might have caused the problem." Failed: 0x1fRepair Action: System FilesFailed: x490There were more options to select for a recovery task, but I didn't try them as they didn't seem to be as salient as the two above.

View 6 Replies View Related

Windows 7 Update - PC Can't Repair Itself Or Safe Boot

Jun 24, 2011

After installing windows 7 update plus one optional hardware update 2 days ago, windows wont start, repair itself, or safe boot. What should I do?

View 4 Replies View Related

Restore & Repair Don't Work?

Aug 31, 2012

my Windows 7 64-bit computer acted oddly (after it accidentally got unplugged while on, tho not sure that's what did it). now when i boot i get as far as the windows 7 logo starts to show, then i get that it can't boot.

i changed nothing that i know of. repair says it can't. restore, which only lists points from 3 days ago, doesn't work. i did a memory test. it was fine. am i doomed to do a clean re-install of Windows 7?

btw, if i get that Windows 7 logo, and also a stage where it says it is loading files, that means it is reading from my hard drive, right?

View 5 Replies View Related

Restore & Repair Don't Work

Aug 31, 2012

my Windows 7 64-bit computer acted oddly (after it accidentally got unplugged while on, tho not sure that's what did it). now when i boot i get as far as the windows 7 logo starts to show, then i get that it can't boot. i changed nothing that i know of.

repair from my bootable Windows 7 disk says it can't. restore, which only lists points from 3 days ago, doesn't work. i did a memory test. it was fine.

am i doomed to do a clean re-install of Windows 7?

btw, if i get that Windows 7 logo, and also a stage where it says it is loading files, that means it is reading from my hard drive, right?

View 1 Replies View Related

Windows 7 Freezes / Loaded Programs Does Not Work - Fine In Safe Mode

Jun 5, 2012

My computer runs like grease lightning in safe mode, and my internet speeds are marvellous also, but alas when not in safe mode I have on quite a few occasions lately had my Windows freeze, my Windows Live Mail also freeze. I will define freeze, everything just does not work, my browser Firefox/Google, none of my loaded programs.

I have to leave the computer for about 10 minutes, and then it is perfect all day!, so I am guessing a program is causing the dilemma, but which one? I have about 60 applications running and I haven't loaded a new one in about 6 months. Is there a program I can purchase/download that would seek out the rogue program if indeed it is a rogue program.

View 9 Replies View Related

Bluescreen On Safe Mode And No Restore Points?

Aug 25, 2012

So, I have this system, and it bluescreens when I boot in to both "normal" and save modes, however it reboots instantly, so I can't see the error. I have gone into recovery console, and there are no system restore points. Windows cannot fix the startup "Automatically"

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved