Laptop Won't Boot Up - Startup Repair And System Restore / None Will Finish
Oct 21, 2012
My Sony vaio just turned off last week and wont boot up. It turns on an flashes Sony vaio but that's all. I made a recovery disk and I can get into bios so I tried booting from internal disk and tried startup repair got nothing, tried system restore for every restore point and none will finish. Took each piece of ram out an tried starting it up to see if bad ram was the problem and it starts the same way. I also tried the restore from previous image but I have no image. So I don't know what else to try. Windows 7
View 15 Replies
ADVERTISEMENT
Feb 15, 2013
Living is south FL can be a bitch when the rains come as there often is a ton of accompanying lightening that plays havoc with the electrical system, even though I have surge protectors inside and outside the house. We just had some very heavy rains with lightening and my computer shut down several times, but I could restart it each time...except for the last time when Windows wouldn't startup. At that point, Start Up Repair came into play. Although I routinely backup on an external drive, of course I never did it this month-DUH!Results from SUR were error free (error code=0x0) on all the parameters tested, however there were the following error codes reported:"Unspecified change to the system configuration might have caused the problem." Failed: 0x1fRepair Action: System FilesFailed: x490There were more options to select for a recovery task, but I didn't try them as they didn't seem to be as salient as the two above.
View 6 Replies
View Related
Aug 6, 2012
I was being an idiot and messed with Msconfig memory. Restarted and gave me bsod. After that I ran Startup repair system restore failed.I checked the memory box I think it was 0, not sure. if you need additional information let me know.
-What I did Messed with memory in Msconfig
-What I have access to in Startup Repair Cmd
-What I tried System restore Startup Repair
View 1 Replies
View Related
Jan 15, 2012
I recently downloaded a damaged file, which caused my computer (not this one) to be unable to start up normally. The computer now boots up in Startup repair, which is unable to repair my computer "automatically" and when I then click "View advanced options for system recovery and support" and go to the "System restore" tab and choose a Date and time for the restoration, it tells me that "There is not enough free space to restore the disk". I seem to have no options to try and sort out the missing space on the harddisk, which should be unnecessary because I am pretty sure there is still alot of disk space on the C.
View 1 Replies
View Related
Feb 16, 2012
i got a hp pavillion running windows 7 i was installing the windows update and pressed restart now, after this the force restart thing came up but i pressed cancel and it didnt like this, after 2 minutes of program errors it restarted and went straight into startup repair. running it on normal mode doesnt work and safe mode is not available. when it runs startip repair it wont fix anything and tells me to restore, i can get to the windows restore part and have restore points but they do not work and an error is shown, x8000xffff if i remember correctly.
View 2 Replies
View Related
Feb 11, 2013
I have a pavillion dv6- laptop that's stopped being able to boot up windows? It only goes to the screen with the option of starting windows normally (which brings me back to the same screen) or going to startup repair. When I go to repair it says Got some important data in c drive can't install new windows all data will wipe up what to do now?
View 3 Replies
View Related
Jan 4, 2013
A few days ago, I went to turn on my computer and it just gave me a black screen after the "Starting Windows" screen. I attempted to use System Repair, which failed. It said there was an unspecified error possibly caused by a change in system configuration. I have not changed anything on my computer, for the record, between the last time it worked and now. My husband said it downloaded updates, which would explain why it was off in the first place instead of just being on stand-by. Anyway, I then tried System Restore, which also failed. I can get it to start in Safe Mode with Networking, but it seems that everything I try to run to figure out what the problem is, is saying it can't find the problem. I enabled bootlogging and found this...
Did not load driver @nettun.inf,%isatap.displayname%;Microsoft ISATAP Adapter
Did not load driver @nettun.inf,%isatap.displayname%;Microsoft ISATAP Adapter
Did not load driver @nettun.inf,%teredo.displayname%;Microsoft Teredo Tunneling Adapter
Did not load driver @hal.inf,%acpi_amd64.devicedesc%;ACPI x64-based PC
Did not load driver @battery.inf,%*compbatt.devicedesc%;Microsoft Composite Battery
Did not load driver @netavpna.inf,%mp-agilevpn-dispname%;WAN Miniport (IKEv2)
[code]....
View 3 Replies
View Related
Jan 1, 2013
I have recently installed windows ultimate x64 on my computer.i have an asus p6t deluxe v2 mobo, i7-960 cpu and a wd velociraptor hdd. The install went ok, I even managed to restart my computer a few times after but after windows updates installed it won't boot. I tried to boot into safe mode, restore from the installer, and repair, none worked. After startup repair it says: "a patch is preventing the system from starting" and I get a 0x1f error code.(Preventing windows from downloading any updates didn't work either)
View 9 Replies
View Related
Dec 14, 2012
windows 7 startup repair on every boot but after startup repair hibernate works. How to fix?
View 1 Replies
View Related
Sep 25, 2010
I ordered a refurbished/reconditioned Packard Bell EasyNote TJ74 laptop from a very well known retailer in the UK called Currys. I received it two days ago. Initally, the laptop stayed on for all of about 5 seconds before shutting down, however I have solved that problem by Googling the text and looking here: pxe-e61:media test failure check cable. It was basically trying to boot from something other than the HDD itself, so I set the HDD to the top of the list in the BIOS.Then, the next problem I got was this: I get the "Windows is Starting..." screen, and then a setup services starting message, and then this:"Windows could not finish configuring the system. To attempt to resume configuration, restart the computer."I restart the computer and... nothing happens. No Windows installation/recovery disk came with the laptop.So, I set the laptop to boot from CD in the BIOS and, using a 64-bit edition recovery disc I found online and ran startup repair using it, apparently no problems were found, and I got a message about ensuring I didn't have any cameras etc. attached... ..Someone online recommended I disable digital driver signing, so I did that by pressing F8 at one point when it was booting... it doesn't seem to have made any difference. Safe mode doesn't work either.Currys have told me they can do nothing but send a courier to my house to pick up the laptop... I don't get a replacement, simply a refund. I needed this laptop for Monday as I start university.I've set it back to boot from HDD and I'm getting the "Windows could not finish configuring the system, please restart" message again and again and again, and the system just constantly restarts and the same message appears. It is a never-ending loop!
View 4 Replies
View Related
Jan 14, 2011
Ever since I bought my new computer and installed Windows 7 64 bit Pro I have noticed that sometimes when I start my computer the startup locks up or crashes, requiring me to restart or it takes me to the system repair screen and running this process does nothing.
View 9 Replies
View Related
Mar 8, 2012
I am having the following system configuration
XPS L401X Base
Genuine Windows(R) 7 Home Premium 64bit (English)
Intel(R) Core(TM) i7-740QM Processor
6GB 1333MHz DDR3 SDRAM (1 x 2GB + 1 x 4GB)
640GB 7200RPM Hard Drive
Lately whenever i try to start my computer it pass the Dell Bios and then directly goes to the screen which states
Repair your system or Start windows normally When i chose repair system , it start downloading windows files and then launch the windows , but hung up at the sky blue login window with only movable cusor . When i choose to start windows normally it gives me BSOD momentarly ( hard to see the message) and then restarts again . i tried with the advanced boot up options like
repair my computer , all safe modes , restore to last good configuration but it does the same and hangs at windows loging sky blue window .I Tried to run the Dell PSA+ Diagnostic and it returns with 2000-0146 error . As per the Dell online solutions for this type of error ,I tried to reinstall the Hard disk but the problem still exist.
View 3 Replies
View Related
May 9, 2011
Win 7 no boot to windows or safe mode Startup cannot repair or System Restore Drive has changed fron C to D, PC was showing black screen 2 options Start windows normally or Launch Start up repair 1 beepthen launches startup repair.checkingsystem, then cannot repair and send info about this problem.
View 5 Replies
View Related
May 8, 2011
The other day I was trying to figure out what coral paintshop pro meant by security key, so I googled it. Something popped up and asked me if I wanted to download, and I wanted to say no, but my laptop's mouse is too sensitive at times, so I accidentally clicked yes. My computer automatically shut down right after that. Every time I turn it on now, it goes straight into System Repair and it doesn't work, it says it cannot repair. I've tried System Restore, but since that doesn't get rid of the documents that have been downloaded, it isn't helping either. My computer won't even let me enter any form of Safe Mode, it just goes straight back to System Repair.
View 3 Replies
View Related
Feb 27, 2010
How to Automatically Create A System Restore Point at Startup ?
View 0 Replies
View Related
Jun 29, 2012
My system undergoes startup repair everytime i start my computer and after a long process of searching for problems it restarts and the same startup repair problem arises. It also displays the message "This may be caused due to a recent change in any hardware or software of the system". I hv infact installed windows 2-3 times since this prblm started bt still this problem arises.
View 2 Replies
View Related
Jan 1, 2013
I have never had the need t use this disk till now but as I am getting problems starting up I tried System Restore and it didn't work (I have tried 2 restore points).Can I use the repair disk that I created on my HP desktop to mend the system or to restore it to an earlier time ? When I open the repair disk on the computer it just shows a couple of folders (boot ,sources as well as a file called bootmgr but I can't see a hrep file to let me know what I can do...
View 1 Replies
View Related
Jan 26, 2012
Last night I closed my laptop without shutting it down. I woke up this morning and turned it on and it went to the system repair screen and ran through that. It says there are problems but they are not automatically repairable. I then tried to do the system restore to an earlier point in time and had one option for a couple days ago. I ran through that but it says there is an error and when I expand to see the error one of the things listed is no OS installed. I have windows 7 64bit. Why it would say I don't have an OS installed but it is running through the system start up repair as well as listing a date that I could restore it back to. I have not tried installing the hard drive into a new computer yet.
View 9 Replies
View Related
Aug 8, 2012
Hardware Information (This is from memory and may not be completely accurate):The computer model is emachines The processor is a dual core Intel Pentium The graphics card is NVIDIA (Can't remember the model.)4GB of RAM installed Software Information (Also from memory, but this is likely to be more accurate than the hardware.): Windows 7 Home Premium 64bit Antivirus software is Comodo Internet Security - Also the firewall (product information).I often used Advanced System Care for optimization.-product information.after searching the internet for ways to fix my problem for the past three days, I'm at a complete loss. I was told by a professional that my registry was likely corrupted and that my best bet would be to re-install Windows entirely. I was hoping it wouldn't come to that, but was prepared nonetheless.So I inserted the installation disk, and wouldn't you know it, the installer wouldn't recognize my hard drive (BIOS recognizes it though). Searching for reasons why this was happening only turned up people saying to make sure it was recognized by BIOS, which I considered a no brainier. When it still didn't work for people in certain threads, they were told to try wiping their hard drives. I've done it. Windows still doesn't want to notice my hard drive.After that, I decided to try and install Windows to an external hard drive. I know this isn't how Windows was designed, and I knew it wasn't how Windows was meant to be used, but I was (to my knowledge) out of other options (Also, the external hard drive has 1 TB of space on it, so I wasn't concerned about speed loss). So, I searched for ways to do that, and I came across PWboot. The first half of the installation worked, the second half did not. I began getting an error that read (bootmgr is missing press ctrlalt+delete to reboot.) Which I did. But that didn't fix anything. So I tried the entire process again, and it didn't work.The "Repair your computer" feature in the windows install disk turned up nothing as well. I can't "Factory Reset" because it can't detect any installation of windows, the startup repair function can't "repair this computer automatically", and none of the other options will even open (with the exception of the command prompt, but most of the commands aren't valid for some reason.)
View 9 Replies
View Related
Jan 4, 2013
So lately my computer's firewall has decided to not work so I searched around and eventually concluded on doing a upgrade reinstall. As I didn't want to lose any of my files, drivers or programs. All seemed like it went well until the computer rebooted for the last time before it reaches the " Setting up for first use " dialog Though before this was able to happen the computer went into a reboot loop with bsod 0x0000001E
After a large amount of reluctant clicking The computer NOW only boots to the System Recovery Options window and the ONLY option is Startup Repair ; There is NO command prompt no diagnostics, nothing, Just Startup Repair, in which start up repair is unable to do anything and continues to loop itself with a Don't send dialog
I have tried inserting the installation disk and accessing the Repair Computer but it presents an incompatibility error.
I have no F8 menu at all, (no safe mode, which I can't access anyway because the computer can't set up for first use).
View 1 Replies
View Related
Apr 17, 2012
On boot it is taking him to the windows 7 startup repair which fails with StartUpRepairOflline AutoFailover CorruptFile
I have suggested the following, all which have failed to make a difference:
bootrec.exe with /fixmbr /fixboot and /RebuildBcd
Run chkdsk
Startup repair
System Restore - two dates tried
The pc is about a month or so old, and I'm thinking it could be a hardware issue, hard drive?
Two things I am going to try when I get there is a WD Diagnostics on the Hard drive, and the sfc
View 7 Replies
View Related
Jun 4, 2012
I've been having trouble trying to get my computer to boot; I'd noticed a drop in performance (still unsure why) so decided to boot up in safe mode and poke around - it was not my original intention to install AC 5.3.0 but somehow it happened. I ran the 'deep-care' utility and everything was working fine, my computer rebooted and performed a disk check: there weren't any errors that I can remember apart from [something along the lines of] 60 reparse files. Following this my computer restarted and Windows failed to load, restarting to show me startup repair - this isn't the first time this has happened, a similar thing occurred following previous attempts at boosting speed, though before I was able to get Windows up and running using an Ubuntu installation disk... still don't understand why - no need to say that it didn't work this time. Startup repair refuses to work and my system restore points have vanished; I would try doing a repair install if I had a copy of the disk. I built the computer myself a few months back, borrowing a Windows 7 installation disk from a friend (who has now conveniently lost said disk), startup repair does tell me something about 'Problem Signatures'. [code]
View 2 Replies
View Related
Dec 26, 2012
Recently my computer has been randomly just giving me the BSOD. Normally this problem was resolved by a simple restart but tonight about an hour before I posted this, the blue screen sent me back to startup but instead of giving me the usual "Security mode" and Regular Startup. It gave me Startup Repair and normal startup. After clicking normal startup just to see if it would correct itself like normal,my pc instantly BSOD'd, bringing me back to my two options. I've been sitting here staring at the startup repair screen for about an hour now.
View 2 Replies
View Related
May 24, 2009
I used windows update and updated my nividia 9600 drivers and now for the past couple days I have been unable to reach my desktop. It boots to startup repair and does a short scan then finally says it was unable to help will either shut down, restart or scan again. I've DL'd a vista repair to restore but it doesn't have any restore points and I was able to get onto a DE language linux version of my computer but haven't been able to fix it there, partly cus i cant read most of what im seeing.
View 9 Replies
View Related
Dec 26, 2011
I get into startup repair everytime i boot my pc which is never successful. I am definitely goin to explain it in detail but dis is basic problem nd plz dont mind typing coz m typing fast on iphone which may cause errors in typing!Yesterday,i used my pc for 7-8 hrs continuosly which is not big deal but due to it i can't figure out my action which caused problem. I kept it on for downloading at night nd when in morning i got boot screen which comes when pc is directly turned off. I did Start Windows Normally nd i got usual windows 7 loading animation for a secong nd den it started startup repair after that everytime i boot it takes me to startup repair resulting in continuos failure. I hv googled nd found many threads but none matched my exact one. Startup infinity loop didn't work. Below r given few conclusions nd obstacles-1.) i can't get into advanced boot options using F8. But i can get into recovery menu using install dvd nd view advanced options frm startup repair.
2.) System restore din't work. I mean its not successful in restoring.3.) bootrec.exe didnt work4.) imp point to be noted is my last update was on 23 dec while pc worked fine on 24 th & 25th dec means dont knw wat happened 25th night that caused this problem on 26th morning.5.) sfc/scannow says "a startup repair is left to be completed." it says to complete that first then use sfc/scannow.6.) chkdsk results in last line saying failed to transfer log......7.) i also get a report like many others about that problem signature.8.) repair install not possible coz windows can't start only.9.)i hv made a backup using cmd but is there any way without clean install?
View 4 Replies
View Related
Apr 27, 2011
My OS is Windows 7 Ultimate x64 and its boot by vhd.
One day, it failed to go to Windows and stuck at Startup Repair. I think it was caused by invalid driver.
But anyway, my concern is the Startup repair is unable to repair a Windows that is installed in a vhd. Then what should I gonna to do?
View 1 Replies
View Related
Mar 16, 2011
So yesterday I added another hard drive to my computer. I now have 2 SATA hard drives running in my machine. I used the disk managment, and the 2nd hard drive is working as it should.
However, when I shut down my computer and turned it back on, Windows will boot to the Startup Repair screen every time. I checked the BIOS and made sure the boot order was correct, and even took the 2nd hard drive off the boot order in order to make sure it wasn't causing any issues. It's pretty annoying, because every time I start up, I have to wait for the whole repair process before it will load normally. Each time it always says that there are no repairs that could be made.
I also am not able to put my computer in sleep mode any longer. I believe my BIOS setting is set to S1, and before I never had any problems. I would put my comp to sleep and everything would be fine. After the 2nd hard drive, my monitor will turn off and it sounds like 1 of the hard drives turns off, but the CPU and fan are still running and it does not completely go to sleep.
View 4 Replies
View Related
Oct 21, 2012
I've got two hard drives with Windows 7 on it. One of them, the operating system crashed entirely, on the other, it's a perfect copy of how the other hard drive was at factory settings (drivers and all). Now, you're probably wondering, hey, why not use the other hard drive? Thing is, I'm trying to save / keep all the programs on the first hard drive in order to save myself the hassle from 1) pretending I'll find / looking for the disks that I know I don't have and 2) the time it'd take to install them.the machine was *not* giving me anything except sending me over to start up repair, stating that it couldn't fix the problem. I used the other hard drive to boot into Windows, and was hoping to do a repair option on the other hard drive. Unfortunately, I don't think that's entirely possible. I used Hirens Boot CD to check out the System32 / Syswow64 folders, and there was hardly anything in there. So, naturally, started copying off certain sub folders from one to the other. Now, I can get it to attempt to boot / it sees the partition / I go to safe mode, and it hits Classpnp.sys for a split second, then startup repair. Startup repair let's me see that there is one root cause, but, after doing its thing, says that it didn't detect an issue with the startup.
1x Sony Vaio laptop 2x Hard drives (one with a factory restored image on it, another one that won't boot into the OS)The hard drive that I need to boot from / one that has my programs goes to Startup Repair after hitting Classpnp.sys in Safe Mode Startup repair has one thing fail (StartupRepairOffline issue), but says it didn't detect a problem / everything booted fine afterwards Attempted to rebuild the BCD (after successful fixmbr / fixboot), but it states it sees 0 installations of windows. However, I have a Windows 7 retail disk that sees the installation folder.
View 4 Replies
View Related
Jan 8, 2012
My laptop has Windows 7 installed.My Toshiba Satellite L650 started slowing down and freezing every hour or so while for a few weeks which progressively got more often. I thought it was the new modem/router the cable company installed and maybe got a bad virus. I purchased Norton 2012 and after talking w/Toshiba support did a system restore by holding down the "0" button. This seemed to work but not for long, a week later the same issues were occurring. I did another system restore and it worked for a couple of days. Chkdsk did find bad clusters. Now start up repair keeps trying to fix it when I turn it on but it can't.I have ordered a new hard drive from Tiger Direct a few days ago, it is on back order, not sure when I'll get it.I'm afraid to use the start up repair disk that I made on the new hard drive when it does come.My questions are: is there any other way I should be going about fixing this 14 month old laptop?Also, I don't have the original software disks, they didn't come with the computer so I either have to order a copy from Toshiba or should I use that repair disk? Can software cause an issue like this?
View 14 Replies
View Related
Apr 30, 2012
I have a Dell Inspiron N4010 running Windows 7. Last night I was printing off PDF files and listening to a CD when the song that was playing got stuck and the print job I'd just ordered stalled. Then a horrible, loud, relentless sort of whirring noise came out of the speakers and wouldn't stop and the computer was completely unresponsive. This has happened before, last December, and I did what I did then...I just forcibly shut it down. When I started it back up, I could choose between starting normally or running Startup Repair, which was recommended. I swear I chose to start normally, but I can't be totally sure. I walked out of the room to do a couple things and when I went back I saw Startup Repair running and it said it could take over an hour. I had to leave for work in 20 minutes, so I decided to just leave it on. 9 hours later, when I got home, it was STILL going. I tried to cancel, and was informed that the current operation could not be canceled. I forced a shut down again (maybe not the brightest thing but I couldn't think of anything else) and even disconnected the battery. Then I started it up...got the same choice and chose to start Windows...and Startup Repair started again. I managed to cancel and shut down with the OFF button again. Restarted and chose Windows...same thing. Restarted and chose Setup Repair, same result. I cannot do or open anything. I don't know if putting the startup discs in it would even register...and I'm not sure I even have any, as Windows 7 came pre-installed. I haven't backed up my hard drive in a loooong time and I can't afford a new machine.
View 8 Replies
View Related
Dec 9, 2012
I'm new to startup repair and not sure of what it is actually doing but when i start my laptop i get a choice of start windows normally or startup and repair. If i click start windows normally it loads as normal but then i get black screen and the mouse nothing else. When i choose startup repair its attempting repairs and not getting any further.
View 1 Replies
View Related