Configure SATA As IDE Or AHCI

Jun 7, 2009

In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.

If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.

Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.

View 4 Replies


ADVERTISEMENT

Intel Sata Controler ICH10R AHCI + Jmicron AHCI Error

Jul 16, 2009

I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.

As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.

View 3 Replies View Related

Changed The SATA Controller From AHCI To Raid SATA Result = FAILED?

Aug 10, 2010

Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:

At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED

On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.

View 9 Replies View Related

Configure AHCI In Bios?

May 31, 2010

Anyone who knows how to configure AHCI in bios? I'm confused I must say. I want to have eSATA with a sata slot from my motherboard.

View 4 Replies View Related

IDE Or AHCI For SATA Drives (SSD And Regular)

Sep 15, 2009

I would like the good and bad about running your SATA drives in IDE and AHCI modes.

I have 3 drives. 1 SSD and 2 normal hard drives.

Does it even make a difference? I have an Esata bracket that I want to run in AHCI mode but how about the normal system and data drives? What is the best way to set up drives?

View 0 Replies View Related

Coming From XP, Enable AHCI For SATA Drives?

May 11, 2011

I'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.

My questions are:

1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?

2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)

3. I intend to run XP mode, will AHCI mode pose any problems for this?

View 2 Replies View Related

SATA AHCI Controller, IDE DVD RW Slow Speed

Aug 27, 2012

I have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.

My question:

SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s.
TDK DVD+R disks tested OK (on other PC) for 16X capability.
Why is Nero reporting of only 2.4X and 4X writting speeds?

View 7 Replies View Related

SSD Hard Drive - Use SATA As IDE Or AHCI In BIOS

Sep 28, 2012

I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.

But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.

I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.

View 4 Replies View Related

Changing SATA From Compatibility Mode To AHCI?

Oct 18, 2011

I'm installing Seven on a WinXP machine and completed the install, but forgot to change the SATA setting in the bios from "compatibility mode" to AHCI. Now when I change it, windows gives me bluescreen on boot.I'm dumbfounded that Windows Seven startup repair can't fix a problem this simple, but it completely failed, wasn't even able to find a problem.I was thinking it might be easier to just reformat and begin the install over again, or startup in safemode and install the intel SATA drivers... assuming it will let me boot into safemode with AHCI enabled.ps. On the other computer (different thread), I'm going to wait till I have several hours of uninterrupted time, in case I need to begin over installing all the windows versions one at a time. I'll reply with any success/failure on that thread later in the week.

View 4 Replies View Related

Sata Controller From Ahci To Compatible Mode?

Jul 13, 2012

I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.

View 1 Replies View Related

AHCI Mode No Boot From Sata Optical Drives?

Apr 30, 2011

A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.

View 9 Replies View Related

Reinstall Windows 7 Upgrade On New Sata III As C: With AHCI Support?

Dec 18, 2010

Reinstall w7 Upgrade on new Sata III as c: with AHCI support?

View 9 Replies View Related

How To Configure A SATA To Windows 7 For Data

Feb 25, 2011

configure a 320 gig Western digital SATA on a Win 7 Ultimate 32 bit as an Data Drive.I took out the 40 gig IDE that was on the Data end,and replaced it so my wife would have more,Gig space to download more movies and,handle extra information. I went to the BIOS and checked to see if it was activated,I went to the Device Manager to see if the PC was reading it and, it is it says that it'a working properly but the,My Computer wont read it,I'd like to find out how to configure,this device so that you can use it,I have a IDE on my main drive and, wanted to use a SATA on the data drive,since it's more reliable.And on the XP theres a area to go to reformat the disk, on Win 7 I know theres an area you can go to to reformat your hard drive so the computer will read it,when you go to my computer ,will I have to reformat the Sata to NTFS like the rest of the drive's on the PC?

View 3 Replies View Related

Oparating System Not Found When Booting Is Sata Option AHCI?

May 17, 2012

i have an m17 r2 alienwAre laptop.in the bios menu the sata option HCAI is selected but when the comp boots it says no operating system is found when booting for bios sata option RAID it runs fine. But the comp should be on HCAI in order to run features that a specific to that computer . I have tryed reformatting but in HCAI it on finds the second of 2 500g hard drives but the partition with the boot is on hdd1 not hdd2 . Boot up again with RAID it finds both and and I can reformat have tryed to reset the registry and have tryed using drivermax to find out if I'm missing sata drivers I've also tryed reinstalling my bios from the dell

View 6 Replies View Related

Cannot Find Intel 5 Series 4 Port SATA AHCI Controller Drivers For Windows 7

Oct 1, 2011

I'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..

View 6 Replies View Related

Switching BIOS SATA RAID/AHCI Setting Causes BSOD At Windows Start

Mar 30, 2012

I just changed my disk setup from:

1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1

TO:

1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]

Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.


These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.

What am I missing? Why can't I set it to AHCI mode without BSODs?

View 8 Replies View Related

SB600 ATI RAID AHCI Drivers? (BSOD On Boot If In RAID/AHCI Mode.)

Jan 6, 2009

anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).

Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.

(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)

I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.

Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.

Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.

View 0 Replies View Related

SATA 3 Not Working On Asus P6X58D-E Motherboard With SATA III Support?

Jun 27, 2012

Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?

View 9 Replies View Related

Install Sata Hard Drive As A Slave Where The Master Is Also A Sata?

Aug 10, 2011

i want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7

View 4 Replies View Related

SATA-II Drive On SATA Raid Controller?

May 7, 2011

i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?

View 5 Replies View Related

HDD SATA 3 (6.0Gb/s) Works With SATA 2 (3.0Gb/s) Controller?

May 22, 2011

My MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?

View 5 Replies View Related

Asus P6X58D-E - SATA II SSD Or SATA III SSD?

Mar 5, 2012

i'm looking to upgrade from a HDD to SSD. I've been reading online about my board and apparently the marvell 9128 controller sucks speed wise. I was looking at the Corsair Force 3 because of the read/write speeds. Upon doing more digging though it looks like id be better off running a drive on the SATA 2 ports.

View 2 Replies View Related

Replace SATA 1 HDD With SATA 2 HDD?

Oct 23, 2011

The hard drive in my son's laptop has died, it's a SATA 1 (1.5Gb/s) drive. Can I upgrade it to a SATA 2 (3.0 Gb/s) hard disk?? It's in a Toshiba laptop.

View 7 Replies View Related

Installing Both Sata 1 And Sata 2 On Pc

May 18, 2012

I was wondering If I have one sata 1 and an new sata 2(or 3) on my PC installed on my PC will cause problems in transfer speeds? My Blue-ray is sata 1 also.Does this mean that all disks will work as sata 1?

View 2 Replies View Related

Cannot Use AHCI Driver For SSD

Sep 21, 2011

I recently swapped out my motherboard for a Gigabyte GA-970A-UD3. I was trying to overclock my CPU and after a crash and CMOS reset I was no longer able to complete WEI. This was fixed by reinstalling the BIOS firmware but when I ran WEI again, I was now getting a 5.9 score for my SSD (OCZ Agility) when it was previously 7.2.

Now I can no longer get Windows to use the AHCI driver (neither MS nor AMD) for the drive. I am running in AHCI mode but the driver being used for the SSD is a generic "disk drive" (disk.sys and partmgr.sys). When I try to update this driver, it tells me I am using the latest one; it also does not let me manually select the AHCI driver.

After multiple attempts at switching back and forth between IDE and AHCI in the BIOS, uninstalling and reinstalling AMD AHCI drivers, nothing changes. Still the same 5.9 WEI score and generic driver.

View 2 Replies View Related

How To Get AHCI And IDE Mode

Apr 8, 2012

i have an ASUS M5A88-M motherboard, and a Western Digital WD2503ABYX HDD. i am trying to make that drive work in AHCI mode, but when I try, the disk won't boot. i think the HDD is AHCI compatble, tho not certain. i went into the registry to set a value=o for the relevant AHCI parameter, but no luck. if i need a full re-installation of Windows 7 64-bit, does it prompt me along the way to set the mode to IDE or AHCI?.

View 2 Replies View Related

How To Set SSD And HDD In The Bios (AHCI, IDE)

Aug 8, 2012

I have SSD as primary system drive and 2x512GB HDDs as RAID 1 for storage.In bios i have options to set them as AHCI, IDE and one more that i forgot...

View 9 Replies View Related

AHCI Or IDE For Mechanical HDD ?

Jun 24, 2010

Is there any real noticable benefit from having a SATA mechanical HDD use AHCI or IDE? Also, if there is any benefit, is it related to the rpm speed that the drive is capable of?I keep reading conflicting reports on this, some say AHCI is best, others say there is no real difference unless the disk is an SSD.I am about to do a clean install of Windows 7 on a laptop 5400rpm mechanical HDD so thought I may as well set the mode before proceeding with the install.

View 2 Replies View Related

Moving From IDE To AHCI?

Nov 26, 2012

I recently installed Windows 7 Home Premium on a new blank SATA hard drive which I had formatted using the default settings under Windows XP Disk Management.Prior to installing Windows 7 on this PC, I disconnected my other SATA hard drives to preclude any issues during formatting/installation.What I would like to know is whether changing the BIOS disk access mode from IDE to AHCI will impact my ability to access my old hard drives (once I reconnect them)?

View 6 Replies View Related

Changing Between AHCI Or IDE?

Jan 14, 2013

I recently purchased a HP 8440p laptop with Windows 7 Pro. installed. I dicided to partition the drive and install XP-Sp3 on the newly partitioned drive. Before I could load XP I had to change the configuration to IDE. Once I did that all went fine. Now in order to run betwwen OS's I have to set my configuration AHCI for W7 and IDE for XP.

Is there a better way of doing this beside alway re-configuring the bios for AHCI or IDE?

View 8 Replies View Related

AHCI Serial ATA Controller?

Sep 13, 2010

Driver update program says new driver available 1.0. Any issues regarding updating this driver. No problems needed. Dell Inspirion laptop Win 7 Home Prem. 64bit 4gb ram

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved