Changing SATA From Compatibility Mode To AHCI?

Oct 18, 2011

I'm installing Seven on a WinXP machine and completed the install, but forgot to change the SATA setting in the bios from "compatibility mode" to AHCI. Now when I change it, windows gives me bluescreen on boot.I'm dumbfounded that Windows Seven startup repair can't fix a problem this simple, but it completely failed, wasn't even able to find a problem.I was thinking it might be easier to just reformat and begin the install over again, or startup in safemode and install the intel SATA drivers... assuming it will let me boot into safemode with AHCI enabled.ps. On the other computer (different thread), I'm going to wait till I have several hours of uninterrupted time, in case I need to begin over installing all the windows versions one at a time. I'll reply with any success/failure on that thread later in the week.

View 4 Replies


ADVERTISEMENT

Sata Controller From Ahci To Compatible Mode?

Jul 13, 2012

I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.

View 1 Replies View Related

AHCI Mode No Boot From Sata Optical Drives?

Apr 30, 2011

A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.

View 9 Replies View Related

Intel Sata Controler ICH10R AHCI + Jmicron AHCI Error

Jul 16, 2009

I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.

As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.

View 3 Replies View Related

Changed The SATA Controller From AHCI To Raid SATA Result = FAILED?

Aug 10, 2010

Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:

At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED

On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.

View 9 Replies View Related

Configure SATA As IDE Or AHCI

Jun 7, 2009

In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.

If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.

Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.

View 4 Replies View Related

SB600 ATI RAID AHCI Drivers? (BSOD On Boot If In RAID/AHCI Mode.)

Jan 6, 2009

anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).

Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.

(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)

I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.

Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.

Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.

View 0 Replies View Related

IDE Or AHCI For SATA Drives (SSD And Regular)

Sep 15, 2009

I would like the good and bad about running your SATA drives in IDE and AHCI modes.

I have 3 drives. 1 SSD and 2 normal hard drives.

Does it even make a difference? I have an Esata bracket that I want to run in AHCI mode but how about the normal system and data drives? What is the best way to set up drives?

View 0 Replies View Related

Coming From XP, Enable AHCI For SATA Drives?

May 11, 2011

I'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.

My questions are:

1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?

2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)

3. I intend to run XP mode, will AHCI mode pose any problems for this?

View 2 Replies View Related

SATA AHCI Controller, IDE DVD RW Slow Speed

Aug 27, 2012

I have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.

My question:

SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s.
TDK DVD+R disks tested OK (on other PC) for 16X capability.
Why is Nero reporting of only 2.4X and 4X writting speeds?

View 7 Replies View Related

SSD Hard Drive - Use SATA As IDE Or AHCI In BIOS

Sep 28, 2012

I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.

But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.

I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.

View 4 Replies View Related

Changing Between AHCI Or IDE?

Jan 14, 2013

I recently purchased a HP 8440p laptop with Windows 7 Pro. installed. I dicided to partition the drive and install XP-Sp3 on the newly partitioned drive. Before I could load XP I had to change the configuration to IDE. Once I did that all went fine. Now in order to run betwwen OS's I have to set my configuration AHCI for W7 and IDE for XP.

Is there a better way of doing this beside alway re-configuring the bios for AHCI or IDE?

View 8 Replies View Related

Reinstall Windows 7 Upgrade On New Sata III As C: With AHCI Support?

Dec 18, 2010

Reinstall w7 Upgrade on new Sata III as c: with AHCI support?

View 9 Replies View Related

Oparating System Not Found When Booting Is Sata Option AHCI?

May 17, 2012

i have an m17 r2 alienwAre laptop.in the bios menu the sata option HCAI is selected but when the comp boots it says no operating system is found when booting for bios sata option RAID it runs fine. But the comp should be on HCAI in order to run features that a specific to that computer . I have tryed reformatting but in HCAI it on finds the second of 2 500g hard drives but the partition with the boot is on hdd1 not hdd2 . Boot up again with RAID it finds both and and I can reformat have tryed to reset the registry and have tryed using drivermax to find out if I'm missing sata drivers I've also tryed reinstalling my bios from the dell

View 6 Replies View Related

Cannot Find Intel 5 Series 4 Port SATA AHCI Controller Drivers For Windows 7

Oct 1, 2011

I'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..

View 6 Replies View Related

Switching BIOS SATA RAID/AHCI Setting Causes BSOD At Windows Start

Mar 30, 2012

I just changed my disk setup from:

1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1

TO:

1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]

Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.


These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.

What am I missing? Why can't I set it to AHCI mode without BSODs?

View 8 Replies View Related

Latching Sata Cables Compatibility?

Aug 17, 2011

how can i tell if my mobo(gigabyte 880ga-ud3h rev3.1) is compatible with the latchling type sata cables?

View 4 Replies View Related

How To Get AHCI And IDE Mode

Apr 8, 2012

i have an ASUS M5A88-M motherboard, and a Western Digital WD2503ABYX HDD. i am trying to make that drive work in AHCI mode, but when I try, the disk won't boot. i think the HDD is AHCI compatble, tho not certain. i went into the registry to set a value=o for the relevant AHCI parameter, but no luck. if i need a full re-installation of Windows 7 64-bit, does it prompt me along the way to set the mode to IDE or AHCI?.

View 2 Replies View Related

How To Run Windows XP On AHCI Mode

Aug 7, 2012

Everytime i want to swap hard disk with different OS, WinXp(IDE) to Windows 7(AHCI), i need to do change some hard disk setting on BIOS. Is there any way that i can do to make both hard disk with different OS compatible on the desktop PC without change any setting on BIOS everytime i change hdd? Is there a way to make WinXP IDE mode to run under AHCI mode?

View 1 Replies View Related

[BIOS] Can't Boot From CD-ROM In AHCI Mode

Feb 9, 2011

I'm trying to do a startup repair of Windows 7 x64 on an SSD but can't boot from the CD-ROM while in AHCI mode. I have set CD-ROM at the top of the boot order in BIOS but this is just ignored and the computer boots from the SSD with the knackered version of W7x64. I read somewhere that when in AHCI mode, the BIOS boot order may include "CD-ROM" but it's not the real device anymore. I tried looking for the CD-ROM by its manufacturer name in the list under Hard Drives but it's not there either.So just how do I go about booting from the CD-ROM in AHCI mode? No problems booting if I set the BIOS back to IDE mode, install Windows 7 and then do the registry hack to install the AHCI drivers, but I'd like to be able to boot from the CD-ROM in AHCI mode.

P.S. I have a Gigabyte GA-MA78GM-US2H motherboard and am using the latest BIOS version (F9D)

View 2 Replies View Related

BSOD During Boot On AHCI Mode

Mar 31, 2012

My motherboard is a Gigabyte Z68XP-UD3 Revision 1.3, my OS is Windows 7 Professional 64 bit, my HDD is a Seagate 1.5tb, and my SSD is an OCZ Agility 3 60gb.

So i was using Intel Smart Response technology with my SSD for SSD caching, everything was pretty much working fine. The other day i flashed my bios using @BIOS without properly disabling my smart response configuration, which i probably shouldn't have done and i won't do again. When i rebooted, Intel Rapid Storage technology was acting up and when i tried to open it, it said "IAStorUI.exe has stopped working". After that, i uninstalled the program and tried to re-install it, but during the install it said "This computer does not meet the minimum requirements for installing the software." After a little research, i found out that it meant that my bios was set in IDE mode instead of ACHI mode. I am not sure what the mode was before i flashed my bios, but it was probably some sort of raid that it used for SSD caching. When i went into the bios and switched from IDE to AHCI, windows would blue screen after performing a few seconds of the boot logo. I switched back to IDE, and did some research to find out about the "Start" registry in HKEY_LOCAL_MACHINESYSTEMCurrentControlSetservicesmsahci. I switched that from 3 to 0, and windows was able to boot into AHCI mode and automatically got drivers. Then, i tried re-installing Intel Rapid Storage technology. It was able to install, and i rebooted my computer. It blue screened again on the same part of the boot logo as before. I had to switch back to IDE mode to get it working again. Then, i got new chipset drivers from Intel's website, which didn't help. The registry that i changed is still set to zero, but it just won't successfully boot with AHCI like it did the first time i changed the registry. I am very stumped and i dont know what i could do to make it work like it did before i flashed my bios. My friend recommended that i should reinstall windows, but then i would have to go through the trouble of getting everything back and i think there should be some way of doing this without reinstalling the os.

The bottom line is that windows blue screens when the bios is in AHCI mode, even though i have the registry that should fix that and that did fix it on one boot set to zero.

View 1 Replies View Related

Windows 7 Won't Boot After Changing Drive's Sata Connection

Apr 30, 2011

I need to move the sata connection for my drive "D" on the motherboard, however after moving it Windows 7 won't boot.

Gateway LX6820, 8GB Ram Windows 7 HOMEPREMIUM 64 bit Drive "C"- Intel X25V SATA SSD 40GB, has 200MB System Partiton for MBR and the rest is for the OS Drive "D"- WD Raptor SATA 150GB, has User folders, Program Data, and Programs installed

I have a fresh install of Windows 7 HOMEPREMIUM 64 bit that was done with drive "D" in one of the hotswap bays. All my tweaks, and settings changes are done and Windows operates with no problems. Now I wan't to move the drive to an internal bay. The set up and install was done using sata 4 on the motherboard but due to cable routing I need to use sata 2 for the move.

After the physical move and cable change Windows sees the Raptor as drive "E" not "D", it can't access the user profile and loads a default profile instead. This default profile won't allow access to disk management so I can change the drive letter. I have tried using Diskpart to reassign the drive letters but when I boot into Windows it changes it back to "E" again (must be due to the sata port 2 being assign "E" in an earlier configuration?). I tried using Windows repair but it changes the boot sector to"C", the "C" drive to "D" and the Raptor to "E", had to change the cables to the original locations and do a system restore to fix that one.

View 2 Replies View Related

Windows 7 Won't Boot After Changing Drive's Sata Connection

Apr 29, 2011

I need to move the sata connection for my drive "D" on the motherboard, however after moving it Windows 7 won't boot.

Gateway LX6820, 8GB Ram
Windows 7 HOMEPREMIUM 64 bit
Drive "C"- Intel X25V SATA SSD 40GB, has 200MB System Partiton for MBR and the rest is for the OS
Drive "D"- WD Raptor SATA 150GB, has User folders, Program Data, and Programs installed

I have a fresh install of Windows 7 HOMEPREMIUM 64 bit that was done with drive "D" in one of the hotswap bays. All my tweaks, and settings changes are done and Windows operates with no problems. Now I wan't to move the drive to an internal bay. The set up and install was done using sata 4 on the motherboard but due to cable routing I need to use sata 2 for the move. After the physical move and cable change Windows sees the Raptor as drive "E" not "D", it can't access the user profile and loads a default profile instead. This default profile won't allow access to disk management so I can change the drive letter. I have tried using Diskpart to reassign the drive letters but when I boot into Windows it changes it back to "E" again (must be due to the sata port 2 being assign "E" in an earlier configuration?). I tried using Windows repair but it changes the boot sector to"C", the "C" drive to "D" and the Raptor to "E", had to change the cables to the original locations and do a system restore to fix that one.

View 9 Replies View Related

BSOD When Installing Windows 7 In AHCI Mode

Jan 24, 2011

First thing, my build:
Board: Gigabyte GA-P55A-UD4
CPU: Core i7 870 @ 2,93 Ghz
Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18
Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD
Running: Windows 7 Ultimate
Trying to install: Windows 7 Ultimate
PSU: LC Power Arkangel 850W

I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally.

I didn't know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the HDD? Anyway, I really want to start using the disk. I have tried installing Windows 7 from a dvd as well as from a USB key.

View 5 Replies View Related

Why Does Windows 7 Freeze When Try To Switch To AHCI Mode

Jan 1, 2012

I changed the appropriate setting in the registry. (msachi > start: 0) Then I changed the setting in my motherboard and Windows froze upon starting up, and my system rebooted.

The thing is, I changed it to AHCI before. It worked fine! I then switched back to IDE while trying to fix a problem with eSATA detection (turned out to be a faulty cord), Now I can't switch back! Sigh. I really would like my eSATA to be plug and play.

View 4 Replies View Related

BSOD When Installing Windows 7 In AHCI Mode

Jan 24, 2011

First thing, my build: Board: Gigabyte GA-P55A-UD4 CPU: Core i7 870 @ 2,93 Ghz Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18 Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD Running: Windows 7 Ultimate Trying to install: Windows 7 Ultimat PSU: LC Power Arkangel 850W
Ok so here's the deal. I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally. I didnt know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the disk? Note: I have tried installing Windows 7 from a dvd as well as from a USB key.

View 7 Replies View Related

AHCI Mode Stopped Reconizing Hard Drive

Oct 3, 2012

If the BIOS setting for the hard drive controller is AHCI it will not recognize the drive. (This was the default setting in the BIOS), If changed to IDE mode it recognizes the drive but come up with an "No operating system detected" message. If the hard drive is installed in a second lap top it works fine. If another hard drive is installed it works fine in AHCI mode. Only the combination of the original hard drive and the original lap top wont work.

View 9 Replies View Related

Cannot Start Windows 7 In AHCI Mode When Multiple Drives Are Connected

Nov 11, 2011

i'm working with a new pc build that uses a 60 gb ssd for its boot drive, and which is also reusing some "old" sata hdds for storage.

at the time i installed windows 7 ult 64, i had only a new ssd plugged in, and the bios was set to ahci mode. the installation went fine and i was able to boot into windows afterwards without issue.

then, i connected a wd caviar black sata hdd to use as storage, with the ssd being the boot drive. with both of them connected, windows will not get past the starting windows screen.

i made this video of the program before i understood that it was a drive controller issue: startup problem - Internet in it, you can see that windows boots fine in ahci mode with just the ssd plugged in, but that when the backup sata drive is also connected it doesn't get past the starting windows screen.

for the record, this caviar black hdd was my previous boot os, and it also has a windows 7 install on it (which i've renamed the base folder of), but it is not booting from that hdd. also, i have tried the same thing with other "old" sata hdds that do not have any previous windows install on them, and the result is the same thing which is shown in the video.

View 9 Replies View Related

Restored Windows 7 HP 64bit System Image - Won't Boot In AHCI Mode

Jun 29, 2011

I created a system image on an AHCI system, then I replaced the hard drives & re-imaged the system. Now Windows won't boot in AHCI mode, it has to be it IDE mode. Why is it not booting in AHCI mode?

View 5 Replies View Related

Windows 7 64bit PC With 3 X 3TB Hard Drives No Longer Boots In AHCI Mode?

Jul 5, 2011

I successfully installed Windows 7 64bit in AHCI mode on a PC with 3 new 3TB Western Digital WD30EZRX Caviar Green hard drives.Then I installed "Intel Matrix Storage Manager Driver [v8.9.0.1023]" & as soon as Windows restarted after installing it, Windows would not boot, & will now only boot in IDE mode.In IDE mode I have to do a system restore to the point before installation of "Intel Matrix Storage Manager Driver" to be able to boot again in AHCI mode.

View 1 Replies View Related

Change Storage Controller To AHCI Mode Post Install (windows 7 64-Ultimate)

Sep 19, 2011

Can someone hit me with a link for manually installing the AHCI driver and switching the OS mode for the storage controller.

If I remember right, this is just putting the driver in /sys/drivers, running a script, and making a registry change. Then you reboot, change the motherboard setting, and then install IMSM after the OS comes back up. I don't remember the script, or if it was just a reg edit, etc.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved