Cannot Find Intel 5 Series 4 Port SATA AHCI Controller Drivers For Windows 7
Oct 1, 2011
I'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..
View 6 Replies
ADVERTISEMENT
Jul 16, 2009
I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.
As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.
View 3 Replies
View Related
Aug 10, 2010
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
View 9 Replies
View Related
Aug 27, 2012
I have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.
My question:
SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s.
TDK DVD+R disks tested OK (on other PC) for 16X capability.
Why is Nero reporting of only 2.4X and 4X writting speeds?
View 7 Replies
View Related
Jul 13, 2012
I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.
View 1 Replies
View Related
Jan 19, 2009
Can't find drivers for Intel SM Bus controller on ASUS P5Q Pro
View 9 Replies
View Related
Feb 25, 2011
I have an asus m2n32ws pro motherboard and am running win 7 ultimate 64 bit and have a problem device _ it is a sata controller that has no driver and i have searched and cannot find out a what the device is nor b a driver anywhere
View 6 Replies
View Related
May 5, 2009
My computer has the ancient Intel GMA 900 videocard series. The 32 bit RC1 install includes the driver, and works fine. However when I tried installing 64 bit RC1, there wasn't any driver included and it showed up in device manager as "Standard VGA adapter". I've been looking around but the only 64 bit driver I found for this card only works for XP, and 7 refuses to install it. Any help?
View 8 Replies
View Related
Oct 27, 2011
Quick summary: SATA Controllers on motherboard are not working. Ordered and installed a PCI-E SATA Controller Card. Connected Hard Drive & DVD Drive to new card ports. Upon attempting to boot installed windows 7, it spontaneously restarts before loading. It seems that I need to get the Controller Card's drivers installed. i try startup repair mode, and I can load the driver and see the Windows 7 installation after that, but then I don't know how to permanantly add the drivers for this installation.
View 1 Replies
View Related
Mar 12, 2009
I have an adaptec sata controller card, which I was contemplating using for running my two raid drives.
I know that there are Vista 64 drivers availiable to download, and so my question is this,
will Vista 64 disk drivers work with Windows 7 Beta build 7000?
I thought i'd ask here first, as it seems silly to reformat and save disc images, reinstall etc, if someone here already knows the answer.
Also, is there a simple way transferring all the user's data and programme data if I wanted to upgrade to a newer build, as obviously backing up the disc image won't work I suppose with a newer build of 7?
View 9 Replies
View Related
Sep 18, 2011
I want to dual boot Win XP and and Win 7 and I need my SATA drivers. I've been searching the internet and the ASUS website but I can't find the SATA drivers.I have an ASUS G73JH. I can't find my MoBo model. I used everest but it says unknown motherboard. My hard drive is a Seagate Momentus St9500420as.
View 8 Replies
View Related
Oct 19, 2011
i want ethernet controller driver for intel core i5 n windows 7
View 3 Replies
View Related
May 6, 2011
I have an Acer computer that the Wan miniports either were corrupted or missing. Is there web site to go to to download these drivers or do I have to reload Windows 7 or purchase a new nic card?
View 2 Replies
View Related
Dec 18, 2010
Reinstall w7 Upgrade on new Sata III as c: with AHCI support?
View 9 Replies
View Related
Jun 9, 2011
AHCI Port Error 0 Press F2 to continue. This error shows on my Gateway zx4800 but when I press F2 nothing happens. S.M.A.R.T capable and status BAD.....it also show this above the AHCI error. My hdd works with other PC.
View 2 Replies
View Related
Jul 21, 2012
I had one problem, I upgrade windows 7 professional 64bit OS on Dell optiplex 380,but Ethernet control driver missing, what do me?
View 1 Replies
View Related
Jun 7, 2009
In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.
If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.
Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.
View 4 Replies
View Related
Dec 23, 2011
Whatever this is has really messed up my computer! I can't play any DVDs or any video that uses Flash or Shockwave! I'm getting desperate, I have used Driver Genius Professional to no avail.Intel no longer offers any kind of support, I have tried downloading their general driver but every time it locks up and crashes, I assume for the same reason the Flash and Shockwave does.
View 4 Replies
View Related
Mar 30, 2012
I just changed my disk setup from:
1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
View 8 Replies
View Related
Sep 15, 2009
I would like the good and bad about running your SATA drives in IDE and AHCI modes.
I have 3 drives. 1 SSD and 2 normal hard drives.
Does it even make a difference? I have an Esata bracket that I want to run in AHCI mode but how about the normal system and data drives? What is the best way to set up drives?
View 0 Replies
View Related
May 11, 2011
I'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.
My questions are:
1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?
2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)
3. I intend to run XP mode, will AHCI mode pose any problems for this?
View 2 Replies
View Related
Sep 28, 2012
I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.
But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.
I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.
View 4 Replies
View Related
Oct 18, 2011
I'm installing Seven on a WinXP machine and completed the install, but forgot to change the SATA setting in the bios from "compatibility mode" to AHCI. Now when I change it, windows gives me bluescreen on boot.I'm dumbfounded that Windows Seven startup repair can't fix a problem this simple, but it completely failed, wasn't even able to find a problem.I was thinking it might be easier to just reformat and begin the install over again, or startup in safemode and install the intel SATA drivers... assuming it will let me boot into safemode with AHCI enabled.ps. On the other computer (different thread), I'm going to wait till I have several hours of uninterrupted time, in case I need to begin over installing all the windows versions one at a time. I'll reply with any success/failure on that thread later in the week.
View 4 Replies
View Related
May 7, 2011
i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
View 5 Replies
View Related
Jun 26, 2012
When I start up my pc I my screen stops at the POST screen where down to the bottom it says AHCI Port 0 error...I never had that error before as normally I won't even see the POST screen.
View 14 Replies
View Related
Apr 30, 2011
A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.
View 9 Replies
View Related
May 17, 2012
i have an m17 r2 alienwAre laptop.in the bios menu the sata option HCAI is selected but when the comp boots it says no operating system is found when booting for bios sata option RAID it runs fine. But the comp should be on HCAI in order to run features that a specific to that computer . I have tryed reformatting but in HCAI it on finds the second of 2 500g hard drives but the partition with the boot is on hdd1 not hdd2 . Boot up again with RAID it finds both and and I can reformat have tryed to reset the registry and have tryed using drivermax to find out if I'm missing sata drivers I've also tryed reinstalling my bios from the dell
View 6 Replies
View Related
Jul 2, 2012
I cant find drivers for USB NETWORK CONTROLLER.
View 6 Replies
View Related
Jan 21, 2012
I am building a htpc but cannot seem to get windows to install onto my SSD.The SSD is visible in BIOS and on the 'where do you want to install windows' screen.I am wondering if that is because the OS cannot install to my mobos sata 3 portsI havecrucial m4 SSD 4GBMSI H61MA-E35 with usb3/sata3The sata 3 ports are ASmedia according to the manual.i think i know where this is heading and will be fairly annoyed if so because i bought this board specifically for the sata 3 boot drive option.
View 5 Replies
View Related
May 22, 2011
My MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?
View 5 Replies
View Related
Sep 3, 2011
Satellite A10 Model PSA10A-3V1KK Graphics Driver.Im trying to run win 7 on this relic and so far so good except the graphics card is a freaking nightmare to sort and toshiba are useless in most areas of support, does anyone know where i can find non proprietary drivers for the Intel 82852/855 GM Integrated graphics chipset.
View 1 Replies
View Related
