HDD SATA 3 (6.0Gb/s) Works With SATA 2 (3.0Gb/s) Controller?
May 22, 2011My MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?
View 5 Replies
ADVERTISEMENT
Changed The SATA Controller From AHCI To Raid SATA Result = FAILED?
Aug 10, 2010Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
SATA-II Drive On SATA Raid Controller?
May 7, 2011i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
View 5 Replies View RelatedSATA 3 Not Working On Asus P6X58D-E Motherboard With SATA III Support?
Jun 27, 2012Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?
View 9 Replies View RelatedInstall Sata Hard Drive As A Slave Where The Master Is Also A Sata?
Aug 10, 2011i want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7
View 4 Replies View RelatedSata PCI I/O Controller Add-on Card
Jan 11, 2009I purchased this add-on card for my older AMD 2400mhz 1gb ram box. This is the computer with Windows 7 on the 500gb Pata IDE hard Drive. I wanted to add a 1TB Sata drive since the MB does not have sata. The card has 2 sata connections, 4 USB ports, & 1 IDE connection. It just plugs into an empty PCI slot. For some reason Windows 7 does not detect the card & when I try to install the drivers Windows 7 says cannot detect any hardware. The card has VIA VT6421A chipsets.
View 4 Replies View RelatedInstall SATA Controller Driver
Nov 5, 2009I've just bought parts and collected a new PC system. My Motherboard is AsRock M3A785GXH/128 ASRock > Products > M3A785GXH/128M
and regarding to the manufacturer it should be Windows 7 hardware ready.
But I can't install Windows 7 pro 64 bit on my new system. The Windows 7 installation application can't see my harddrives and want a driver to them. I assume that should be a driver for the SATA controller on the motherboard. I've tryed to use the drivers on the motherboard cd-rom and tryed to use the drivers froms asrock homepage, but Windows 7 wont accept them.
I have contacted AsRock about this issue, but I'm wating for an answer and hoped that you guys might has seen this problem before, and will answer quicker than AsRock Support
I should say that I cant install Windows Vista Business 64bit without any problems at all.
Adaptec SATA Controller Drivers
Mar 12, 2009I have an adaptec sata controller card, which I was contemplating using for running my two raid drives.
I know that there are Vista 64 drivers availiable to download, and so my question is this,
will Vista 64 disk drivers work with Windows 7 Beta build 7000?
I thought i'd ask here first, as it seems silly to reformat and save disc images, reinstall etc, if someone here already knows the answer.
Also, is there a simple way transferring all the user's data and programme data if I wanted to upgrade to a newer build, as obviously backing up the disc image won't work I suppose with a newer build of 7?
Add A Sata Controller Card To System?
Sep 26, 2011what Sata card i need to add extra hard drives to my system I am running Windows 7 Ultimate 64 Bit
View 3 Replies View RelatedCan't Install On SSD Via SIL3114 SATA Controller
May 24, 2011The mobo's kinda old, and not the greatest; the builtin SATA only works for Raid, so I put in a PCI sata card with the SIL3114 chipset. The computer now sees the 64GB SSD Patriot HD I'm trying to use for her C drive (The SSD is a leftover from a different project... I thought it'd lend some additional performance to help make up for the 1.2 ghz cpu). When I get into Windows setup, though, Windows 7 does not recognize the drive, and none of the drivers that came with the PCI card seem to work. I suppose I should have double checked before buying the SATA PCI card to find one that has native Windows 7 drivers, but I thought the stone age days of needing SATA drivers were over, guess I was wrong!
View 4 Replies View RelatedCannot Find A Driver For A Sata Controller
Feb 25, 2011I have an asus m2n32ws pro motherboard and am running win 7 ultimate 64 bit and have a problem device _ it is a sata controller that has no driver and i have searched and cannot find out a what the device is nor b a driver anywhere
View 6 Replies View RelatedNforce2 Sata Controller SIL3112A Driver
Jul 28, 2009I´m trying to install Seven x86 on Abit NF7-S v2.0 with Sata HDD (non RAID), tried several drivers but didn´t work.
Have you got some working driver for this old chipset? The sata controller is SIL3112A.
SATA AHCI Controller, IDE DVD RW Slow Speed
Aug 27, 2012I have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.
My question:
SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s.
TDK DVD+R disks tested OK (on other PC) for 16X capability.
Why is Nero reporting of only 2.4X and 4X writting speeds?
Sata Controller From Ahci To Compatible Mode?
Jul 13, 2012I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.
View 1 Replies View RelatedAsus P6X58D-E - SATA II SSD Or SATA III SSD?
Mar 5, 2012i'm looking to upgrade from a HDD to SSD. I've been reading online about my board and apparently the marvell 9128 controller sucks speed wise. I was looking at the Corsair Force 3 because of the read/write speeds. Upon doing more digging though it looks like id be better off running a drive on the SATA 2 ports.
View 2 Replies View RelatedSilcon Image 3114 Sata Raid Controller?
Nov 24, 2009Does anyone know where I might find the 64 bit ".inf" drivers for Windows 7 64 bit?
View 3 Replies View RelatedUpdated SATA Controller And 3 Disk Drives Disappear?
Oct 23, 2012I updated the SATA AHCI controller from device manager and rebooted. Shortly after I noticed disk drives F:, Z:, and X: are gone. No big deal I'll just repartition right? No they aren't showing up in Disk Management? The driver I installed I got from gigabyte it was a preinstall driver for ahci. I just installed windows 7 64 yesterday to a Samsung 830 256gb and it was working fine maybe I shouldn't have messed with it. C: drive is working fine just the other 3. Should I roll the driver back? System restore? Did I install the wrong driver?
View 3 Replies View RelatedFlashing Bios On An Adaptec 1220 SATA Drive Controller
May 26, 2009I'm going to install RC1 in the next few days.
I was looking to test the stability within RC1 of an adaptec 1220SA card I have to control the system drives. I have the Vista 64bit driver for the card as this is the newest listed.
I have created a recovery disc in beta build 7000 and hope to use this to boot into a DOS shell and follow the instructions given on the adaptec site:
This is the BIOS release v6.0-0 Build 2330 for the Adaptec SATA II RAID 1220SA Controller.
This BIOS should only be used together with Driver v1.6.12086 in Windows Server 2008 or Windows Vista.
This self-extracting archive includes the flash utility, the BIOS image file and the Release Notes.
Caution: If the BIOS update fails with an error message "unable to find file" or "target controller does not match", please see ASK Answer ID 15241
Installation Instruction: This file is self extracting and will unzip to the directory adaptec1220sa. Copy the expanded files to a floppy diskette. The expanded files can also be copied to a USB device or CD-R.
Shut down the operating system and reboot to DOS from a bootable floppy disk, USB device or CD-R. Insert the media with the update files. Run the flash utility program named AFU.EXE included in this download to backup the current BIOS and flash the new BIOS image.
I'm hoping to expand the bios update file onto a cd for the second drive or alternatively stick it on a USB stick.
My question is this, when I am in the dos shell, what do I do!
I suddenly realised that i've never had a need to use the command line
New SATA Controller Card, Windows Wont Boot, How To Load Drivers
Oct 27, 2011Quick summary: SATA Controllers on motherboard are not working. Ordered and installed a PCI-E SATA Controller Card. Connected Hard Drive & DVD Drive to new card ports. Upon attempting to boot installed windows 7, it spontaneously restarts before loading. It seems that I need to get the Controller Card's drivers installed. i try startup repair mode, and I can load the driver and see the Windows 7 installation after that, but then I don't know how to permanantly add the drivers for this installation.
View 1 Replies View RelatedInstall Windows To Sata Controller Card With Hard Drive Connected
Nov 3, 2012i installed a sata controller because the sata controller on the motherboard went out. I can easily install ubuntu but when i try installing win 7 it asks for a cdrom driver, when i try booting from usb it asks for hdd driver.
View 1 Replies View RelatedCannot Find Intel 5 Series 4 Port SATA AHCI Controller Drivers For Windows 7
Oct 1, 2011I'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..
View 6 Replies View RelatedReplace SATA 1 HDD With SATA 2 HDD?
Oct 23, 2011The hard drive in my son's laptop has died, it's a SATA 1 (1.5Gb/s) drive. Can I upgrade it to a SATA 2 (3.0 Gb/s) hard disk?? It's in a Toshiba laptop.
View 7 Replies View RelatedInstalling Both Sata 1 And Sata 2 On Pc
May 18, 2012I was wondering If I have one sata 1 and an new sata 2(or 3) on my PC installed on my PC will cause problems in transfer speeds? My Blue-ray is sata 1 also.Does this mean that all disks will work as sata 1?
View 2 Replies View RelatedSATA Drivers
Nov 29, 2009I'm getting ready to remove Windows 7 RC and install my legit copy of Windows 7 on my PC. My version of Windows 7 is a XP Pro -> Windows 7 Pro upgrade. When I did this upgrade on my laptop, I ran into a bunch of SATA issues because Windows XP does not support SATA on the default installation disk. Needless to say, a few hours later of messing with nLite, my laptop is good to go.
I want to avoid this mess with my PC and already be prepared. I'm trying to figure out what SATA drivers I need to use with nLite for my main PC. Is there somewhere I can go to get this information? Are the drivers based off my motherboard? CPU? Hard drive? Not sure where to start. My laptop's SATA drivers seemed to be based off the CPU (AMD) going by the name of the driver file.
Mobo: GIGABYTE GA-EP45-UD3P LGA 775 Intel P45 ATX Intel Motherboard
CPU: Intel Core 2 Quad Q9550 Yorkfield 2.83GHz LGA 775 95W Quad-Core Processor Model BX80569Q9550
RAM: G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory Model F2-8500CL5D-4GBPK
VGA: EVGA 896-P3-1255-AR GeForce GTX 260 Core 216 896MB 448-bit GDDR3 PCI Express 2.0 x16 HDCP Ready SLI Supported Video Card
HDD: Western Digital Caviar Black WD6401AALS 640GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive
Sata -IDE Drivers
Dec 2, 2009as far as i can tell i have an amd 780g chipset (intergrated with the motherboard ,the hd3200 package)
The problem im having is my pc wont recognize my sata ide controller and uses "Standard Dual Channel PCI IDE Controller"
Can anyone point me in the direction for the drivers?
Motherboard For USB 3 And SATA 3
Feb 1, 2011Cpu i5 or AMD 1090t or whatever. I can pick out a motherboard that will support USB3 and SATA3 and of course I will have the 2 HD for them. I don't know crap about motherboards but when I pick one out to build my new computer what should I be looking at bus speed and so forth because I don't want to pick out a motherboard that will support them but is slow as mud so why bother so I want to do this right and another hundred here or there don't matter but I don't need a dragster just a Corvet. what I might want to take a hard look at on a motherboard?
View 5 Replies View RelatedWhy Can't Get SATA II Speeds
May 30, 2011I have a Panasonic Toughbook CF-30 MK3. Myself and many others are trying to figure out why we can't get SATA II speeds. There is nothing in the BIOS that helps, nor the manual. The only thing that the BIOS says in the System Info is SATA-AHCI. I have tried several different SSD's and they all max out at around 130Gbps. Someone mentioned that it might not support S-II, but I have a very hard time believing that with the computer only being 2 years old.
View 2 Replies View RelatedIDE To SATA Converter?
Sep 13, 2011I want to add another HD to my PC but all my sata ports are used up, the only other option would be to buy an IDE to SATA converter.
If I buy a converter will the HD behave as if it were using SATA, will the transfer speeds remain the same? Or will it degrade?
Someone told me it would be possible to add 2 devices using the PATA/IDE ports, but so far I've only seen converters that only have an option for 1 IDE device. How many devices can the PATA port support?
What Is Difference Between Sata 1 And 2
Jun 3, 2011what is the difference between the sata 1 and 2?
View 1 Replies View RelatedCannot Find SATA-0
Jun 10, 2011when the computer goes to sleep and then later shuts down, and then when I go to wake it up, it won't boot. The message is Cannot find SATA-0 (Which is the primary boot disc). A physical re-start solves the problem, as it will then boot normally. Is the disc going south? The Check Disk feature says that it is OK.
It is a Dell E520 running Windows 7. It has the latest BIOS upgrade.
Usb To Sata/ide Drivers?
Jul 11, 2012i use the USB TO SATA ADABTOR but that dose not work my windows is 7
View 1 Replies View Related
