Changed The SATA Controller From AHCI To Raid SATA Result = FAILED?
Aug 10, 2010
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
1 SATA HDD Primary OS Disk 2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk 1 SATA HDD Backup Disk [No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
I have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.
My question:
SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s. TDK DVD+R disks tested OK (on other PC) for 16X capability. Why is Nero reporting of only 2.4X and 4X writting speeds?
I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.
I'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..
I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.
As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.
My MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?
In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.
If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.
Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.
I would like the good and bad about running your SATA drives in IDE and AHCI modes.
I have 3 drives. 1 SSD and 2 normal hard drives.
Does it even make a difference? I have an Esata bracket that I want to run in AHCI mode but how about the normal system and data drives? What is the best way to set up drives?
I'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.
My questions are:
1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?
2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)
3. I intend to run XP mode, will AHCI mode pose any problems for this?
I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.
But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.
I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.
I'm installing Seven on a WinXP machine and completed the install, but forgot to change the SATA setting in the bios from "compatibility mode" to AHCI. Now when I change it, windows gives me bluescreen on boot.I'm dumbfounded that Windows Seven startup repair can't fix a problem this simple, but it completely failed, wasn't even able to find a problem.I was thinking it might be easier to just reformat and begin the install over again, or startup in safemode and install the intel SATA drivers... assuming it will let me boot into safemode with AHCI enabled.ps. On the other computer (different thread), I'm going to wait till I have several hours of uninterrupted time, in case I need to begin over installing all the windows versions one at a time. I'll reply with any success/failure on that thread later in the week.
A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.
i have an m17 r2 alienwAre laptop.in the bios menu the sata option HCAI is selected but when the comp boots it says no operating system is found when booting for bios sata option RAID it runs fine. But the comp should be on HCAI in order to run features that a specific to that computer . I have tryed reformatting but in HCAI it on finds the second of 2 500g hard drives but the partition with the boot is on hdd1 not hdd2 . Boot up again with RAID it finds both and and I can reformat have tryed to reset the registry and have tryed using drivermax to find out if I'm missing sata drivers I've also tryed reinstalling my bios from the dell
I am about to acquire a couple (or more) SSD's for an ultra-fast and spacious enough SATA RAID array. Right now I'm thinking RAID 0.
Thing is, I heard by some people that Win7 can't boot from a SATA RAID 0 array, although I am unclear as to whether that is from ALL SATA RAID 0's, or just a few, or an installation error from the users claiming this.
I also haven't found any compatibility lists, which leaves me completely in the dark.
If Win7 can't boot from SATA RAID 0, can it boot from a hardware SATA RAID 5? I'd imagine that any hardware RAID solution would be OK?
I have a Biostar mainboard with Sata Raid 0 enabled. I am trying to install win 7 sp1 but the install process asks for a driver. I thought the drivers are on the win 7 disk itself ? I do not have a floppy disc.
I'm trying to do a fresh install of windows 7 and it wont recognize my hard drives. I've done some research and determined i need the correct drivers, but i don't know which ones. I'm trying to install them on 3 WD3000HLFS in RAID 0. The HDD are plugged into SATA 6 ports( only 2 SATA 3 ports on the mobo).
I am trying to upgrade from Windows Vista 32 bit to Windows 7 32 bit but when booting from the upgrade disk it has problems finding my HDD's and says that windows cannot be installed on them once found.
When choosing a clean install from loading the disk from within Vista it starts to install and then when it restarts it brings up a blue screen saying that windows cannot be installed and is I have installed any new HDD's or controllers then on uninstall them.
When trying to upgrade at first it was complaining about the ATI ACHI Compatable RAID controller not being compatable but now it starts to do the install and then on restart it does the same as the clean install.
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?
I have a W7 64 bit machine and I am trying to update the RAID controller driver without success.I am blocked by W7 from updating the driver and get the "Windows has determined that the best driver is already installed" message.I have tried to work around that and have been unsuccessful.Ultimately I am trying to enable a program "Hard Disk Sentinel" to view and display hard disk SMART info. Unfortunately the RAID driver controlling the HDD's on my PC have a date signature of 2009 and need to be updated to take advantage of SMART information technology
Loading Windows 7 on a new computer. Trying to sort out this raid issue. Computer is :
Gigabyte GA-EP45T-Extreme Processor : Intel Quad Q9400 LGA775 Ram : 4gb Hard Drives : 3 x 1 Tb Seagate Video Card : Radeon HD 4890
I've enabled the raid 5 in the BIOS. I've downloaded the driver from the Gigabyte Disc onto a flash drive. When I load Windows 7 it says " Windows cannot be installed to this disc. This computers hardware may not support booting to this disc. Ensure that the disk's controller is enabled in the computers BIOS menu". I've checked and rechecked the BIOS. I also downloaded the MSM64 Driver in the Gigabyte disc and that the one I copied to the flash drive.
My SSD main drive is running low on space .My motherboard supports 2, SATA3 connections.My current drives are SATA2 SSD main drive and a SATA3 1TB media drive.If I were to add 2 SATA3 SSD's in RAID, does that use up both the SATA3 ports on the motherboard? or do they just combine and use 1?
I'm trying to add 3 additional HDs to my system for storage, using RAID 5 configuration. However, when I set the PCH SATA Control Mode option to RAID(XHD) (in order to enable the motherboard RAID controller) in my BIOS, I get BSOD for a milisecond during the windows 7 loading and then the PC is restarted automatically.
My system spec: Intel CPU i7 2.66MHz, 8GB RAM DDR3 1333MHz GigaByte's Motherboard - GA-P55A-UD3 1 x WD3000HLFS-60G6U2 ATA Device (1x300GB) 3 x ST3500418AS ATA Device (3x500GB) 1 x HL-DT-ST DVD-RAM GH40L ATA Device Windows 7 Ultimate, 64bit
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
