RAID 1 Gigabyte SATA Cannot Find The Array During Windows 7 Install
Sep 10, 2012
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
I would like to get 2 SSDs and put them into a raid array using Windows 7-64bit, but wanted to make sure I understand how to do that. The 2 SSDs will be the only drives in the system. My computer has an X58 motherboard with an ICH10R. Here is what I think is the correct procedure: Boot into the bios. Set the storage config to RAID (the other choices are IDE and AHCI) Reboot and hit Cntrl-I to get into raid menu during boot. Set up the raid array in the setup screen. Reboot to the Windows 7 install CD and install Windows Is this correct? Are there any other steps I need or tips I should be aware of?
I'm trying to do a fresh install of windows 7 and it wont recognize my hard drives. I've done some research and determined i need the correct drivers, but i don't know which ones. I'm trying to install them on 3 WD3000HLFS in RAID 0. The HDD are plugged into SATA 6 ports( only 2 SATA 3 ports on the mobo).
In a new build I'm trying to create a RAID 1 array with two 1TB drives. The drive mode is set to RAID on the Motherboard, and I was able to successfully create the RAID within the Intel Rapid Storage BIOS. Once booted into windows, in the Intel Rapid Storage Technology Window it says recognizes that the RAID is there and says the status is normal. It has been initialized through this program also (although i have read that there is no need to initialize for a RAID 1). In Disk Manager I can see my SSD that windows boots from, and 1 WD 1TB drive (There is 2 there though, but this makes me think that it sees that its a RAID) and it shows it as unallocated space. In "My Computer" the only drive i can see is my SSD. So i guess my question is what do i need to do to make Windows see the RAID in "My Computer"? This is my first RAID build so im new the the RAIDing world.
Last year sometime, my install and all that went flawless, I put Windows 7 64 bit pro on a fresh drive, let it format and install as it wanted, zero problems. Boot drive was alone in the PC, its a WD black 320, I dont have the model or part number in front of me, but it seems to be a solid drive. The PC is a built clone, using Asus mobo and AMD dual core, spec's are in my profile if anyone needs to look that up, basically I don't see any of that mattering in my problem but there you go.added a promise RAID card last night, using an existing array from a previous build, and the system worked great and booted great once. I thought I was home free, but rebooted just to check since I have so little faith in PC's until they work twice, and sure enough I get hung at the glowing windows screen if this card is installed.I have read all I can here on this, and have been thru much troubleshooting... BIOS is fine, boot drive reads fine... the card and its fast track utility see the array fine... all those drives recognize just fine... the problem as I think today is, with the new array in place, windows can't figure out where to boot.
The old array was bootable years ago, so there is probably an MBR on it? I'm guessing a little at this point, but I used to boot to that array but went away from that years ago... since then, and I think I was on win2k back then, but adding an fresh hdd then, and since moving to XP, nothing ever cared... forward to today, Windows 7 does not like this array being in the mix, thus it hangs at the glowing window screen (the starting windows splash where the happy color balls form the win logo)remember, this was all up and running once, so that should eliminate a bunch of trial and error on bad drives, bios issues, and driver stuff... i have been thru the ringer with promise, and they swear the driver is good and is WQHL certified and all that... pulling the RAID card out lets me boot normally, so the hang up is definitely with the presence of this array the catch?? while my boot was C: to begin with, before i ever put the raid in, I put in another solo hdd... i backed up all my pictures to it.. and just before doing all this, noticed that while my C drive and E drive were all legit letter wise, looking in the disk manager, the E drive was listed as disk 0, and the C drive was disk 1... this wasn't a problem at that point, but makes me wonder why on earth the boot drive isn't device 0.
I was contemplating using a Raid 0 array as my primary C: drive with OS. I understand all the issues with that and do regular daily backups. I used to use Acronis which had no trouble with a raid array. But on this new build I was wondering if the built in backup tools would be able to image and more importantly restore my data to the array. My back up drive is not part of the array. I would guess that it would see it just fine from the OS and have no trouble creating the backup image, I am more concerned that if I had to use the rescue disk and reload the image whether or not the array would be visible to the restore disk.
So i have windows 7 installed on one 120g ssd and i want to take the OS and put it on a raid 0 array using two of the same 120g ssds. Whats the best way i can acconplish this?note, the ssd the os is already on will be one of the ssds used in the array
I have a 6TB raid array consisting of 2 3TB drives. I have the latest Motherboard with EFI bios. The Intel RST utility allowed me to set up this array, and it says it is bootable. I would like this to be my C: drive.
How can I get Windows 7 to install and boot from this array.
I'm trying to install Windows 7 64-bit on my brand new custom PC, using a RAID0 drive array. I already set the array in the BIOS, and the BIOS sees it. All shall be going to plan...
Nope.
The beginning of the install goes fine, I accept the Terms and all that good stuff, it's loading files, yadadada.. but when it gets to the part where it's asking me where Windows 7 is asking me what drive it should be on, nothing is there. It asks for drivers (my SB750 RAID drivers) so it can find the drives, I put in my USB flash drive with the RAID drivers (I tried both from disk and website), it tells me that no new devices could be found.
I don't think it's a problem with my physical computer, So it's either that I messed something up in the BIOS or Windows 7 is being picky on it's RAID arrays.
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
Running Windows 7 Ultimate x64. I have setup a partition which I transfered from on drive to another and now my boot partition is on an SSD Raid array connected to an LSI 9260 controller. If I boot the computer with the RAID Array first, the computer will just hang there. No message no nothing after the Verify DMI success message. If I setup my computer to boot from CD first and the the RAID Array second and with a bootable CD in the drive, the BIOS will display the "Press any key to boot from CD" If I don't touch anything, then windows will load just fine when the boot sequence switches to the RAID Array.
I am getting ready to set up a RAID Array but this is my first time doing anything with RAID. I know how to get into the BIOS and change settings and I know with two hard drives, I should do RAID 1. However, I just have a few questions before I do this. First off, I am an idiot and did not notice that my first hard drive I got when I built the computer has a 32 MB Cache:
Caviar Blue 1TB 7,200 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive WD10EALX - OEM
I noticed it only had a 32 MB CACHE when I went to get another one. I then asked for the version with a 64 MB CACHE (WD1002FAEX), paid for it and left. Will these two hard drives work together in RAID if they have different sized caches?
I had a successful raid 5 array setup. It was assigned to g and while I was installing ps3 media server and then java it lost it's drive assignment. It shows up under disk management but asks me to initialize it. I really don't want to do that because it will format and i will lose the data on the volume. What else can i do to get my array to show up in windows with my data intact?
i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
I have been trying to install Windows 7 x64 Ultimate on a Gigabyte GA-P35-DS3 (rev 2.0)
and everytime i do the install fails and the install is then rolled back.
I currently have Vista x32 installed on Gigabyte Raid 0 (there's also an intel raid option but i've never used it). The Vista install runs fine and i've never had a problem.
When i try to install using the GA-P35-DS3 (rev 2.0) raid drivers from the Gigabytes site i get the usual microsoft grumbles about unsigned drivers but then the install seems to go OK from there until the install completes and reboots. At this point it errors out and reboots into the OS rollback install.
Does anyone know if this is an issue with this driver or does anyone have a link to another driver?
So I installed the Windows Seven RC x64 today on my desktop machine after having a great experience on my notebook.
Most things worked out just fine, but the onboard raid controller is giving me alot of trouble (I got two hard disks connected there, should be raid0?), my mainboard is a Gigabyte GA-P35-DS3 an this is SiSoft Sandras report on my disk controllers:
Browsing this forum I found severel interesting posts, for example I tested the drivers of Driver and I tried the mainboard drivers for Vista in compatibility mode, but nothing works. I also looked for the "ITE IT8212 ATA RAID Controller" drivers directly, but there was nothing concerning Windows Seven. After that I tried the Released: Intel Chipset Software 9.1.1.1014 but that still did not solve anything.
How can I uninstall a Gigabyte raid contoller without crashing my Win 7 OS? Uninstall is being prevented because "the OS is on the contoller"! Win 7 64 bit is on a Crucial SSD boot drive and AHCI is set in BIOS. However the raid controller is setting all internal drives to SCSI!
Using Win 7 64-bit with AMD SATA drivers with a strange issue.
When this board boots up it does an AHCI initialization which shows the attached sata drives. After that, Windows 7 loads and runs without a problem. However, when I reboot Windows it sounds like the hard drives spin speed is slowing down then speeding up again.
It does this about 4 times then the computer shuts down. When the computer restarts and goes back to the AHCI init screen it now shows "S.M.A.R.T. Error", but Windows boots without a problem. If the computer is shut down (powered off) the next boot will not show the error.
I've had Windows 7RC 32-bit, and currently also have XP-64 and XP-32 partitions on this machine with no problems at all. If I set the machine to Native IDE instead of AHCI everything goes back to normal with no shutdown issues.
I have a Biostar mainboard with Sata Raid 0 enabled. I am trying to install win 7 sp1 but the install process asks for a driver. I thought the drivers are on the win 7 disk itself ? I do not have a floppy disc.
Loading Windows 7 on a new computer. Trying to sort out this raid issue. Computer is :
Gigabyte GA-EP45T-Extreme Processor : Intel Quad Q9400 LGA775 Ram : 4gb Hard Drives : 3 x 1 Tb Seagate Video Card : Radeon HD 4890
I've enabled the raid 5 in the BIOS. I've downloaded the driver from the Gigabyte Disc onto a flash drive. When I load Windows 7 it says " Windows cannot be installed to this disc. This computers hardware may not support booting to this disc. Ensure that the disk's controller is enabled in the computers BIOS menu". I've checked and rechecked the BIOS. I also downloaded the MSM64 Driver in the Gigabyte disc and that the one I copied to the flash drive.
I'm trying to add 3 additional HDs to my system for storage, using RAID 5 configuration. However, when I set the PCH SATA Control Mode option to RAID(XHD) (in order to enable the motherboard RAID controller) in my BIOS, I get BSOD for a milisecond during the windows 7 loading and then the PC is restarted automatically.
My system spec: Intel CPU i7 2.66MHz, 8GB RAM DDR3 1333MHz GigaByte's Motherboard - GA-P55A-UD3 1 x WD3000HLFS-60G6U2 ATA Device (1x300GB) 3 x ST3500418AS ATA Device (3x500GB) 1 x HL-DT-ST DVD-RAM GH40L ATA Device Windows 7 Ultimate, 64bit
I am about to acquire a couple (or more) SSD's for an ultra-fast and spacious enough SATA RAID array. Right now I'm thinking RAID 0.
Thing is, I heard by some people that Win7 can't boot from a SATA RAID 0 array, although I am unclear as to whether that is from ALL SATA RAID 0's, or just a few, or an installation error from the users claiming this.
I also haven't found any compatibility lists, which leaves me completely in the dark.
If Win7 can't boot from SATA RAID 0, can it boot from a hardware SATA RAID 5? I'd imagine that any hardware RAID solution would be OK?
1 SATA HDD Primary OS Disk 2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk 1 SATA HDD Backup Disk [No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
My SSD main drive is running low on space .My motherboard supports 2, SATA3 connections.My current drives are SATA2 SSD main drive and a SATA3 1TB media drive.If I were to add 2 SATA3 SSD's in RAID, does that use up both the SATA3 ports on the motherboard? or do they just combine and use 1?
I started everything up and entered my new OS disk,thenit says 'loading operating system...' for not even a second then goes on to say'system boot failure, insert system disk and press enter' I re enter the disk but then it says 'disk boot failure, insert system disk and press enter'. I don't know what to do, I've gone into BIOS and but the cdrom as the first boot device also but nothing seems to work.. everything is brand new and my motherboard is GA-970A-UD3 AMD type
when the computer goes to sleep and then later shuts down, and then when I go to wake it up, it won't boot. The message is Cannot find SATA-0 (Which is the primary boot disc). A physical re-start solves the problem, as it will then boot normally. Is the disc going south? The Check Disk feature says that it is OK.
It is a Dell E520 running Windows 7. It has the latest BIOS upgrade.
