SATA RAID Driver - Windows 7 Cannot Be Installed To This Disc
Dec 30, 2009
Loading Windows 7 on a new computer. Trying to sort out this raid issue. Computer is :
Gigabyte GA-EP45T-Extreme
Processor : Intel Quad Q9400 LGA775
Ram : 4gb
Hard Drives : 3 x 1 Tb Seagate
Video Card : Radeon HD 4890
I've enabled the raid 5 in the BIOS. I've downloaded the driver from the Gigabyte Disc onto a flash drive. When I load Windows 7 it says " Windows cannot be installed to this disc. This computers hardware may not support booting to this disc. Ensure that the disk's controller is enabled in the computers BIOS menu". I've checked and rechecked the BIOS. I also downloaded the MSM64 Driver in the Gigabyte disc and that the one I copied to the flash drive.
View 5 Replies
ADVERTISEMENT
Aug 10, 2010
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
View 9 Replies
View Related
Aug 24, 2012
I need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies
View Related
May 7, 2011
i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
View 5 Replies
View Related
Apr 1, 2011
...every time I boot my system, Windows says it is installing the SATA driver. BIOS entries are OK, once drivers are installed, Disk Management shows everything OK too. So, what could be the cause for this? I have two disks, the System SSD (OCD Vertex II 60GB SATA) must have its driver installed to boot Windows, so the msg must refer to the second HD (Seagate 1TB SATA
View 1 Replies
View Related
Sep 15, 2011
I have a Biostar mainboard with Sata Raid 0 enabled. I am trying to install win 7 sp1 but the install process asks for a driver. I thought the drivers are on the win 7 disk itself ? I do not have a floppy disc.
View 9 Replies
View Related
Jun 16, 2011
I'm trying to do a fresh install of windows 7 and it wont recognize my hard drives. I've done some research and determined i need the correct drivers, but i don't know which ones. I'm trying to install them on 3 WD3000HLFS in RAID 0. The HDD are plugged into SATA 6 ports( only 2 SATA 3 ports on the mobo).
View 4 Replies
View Related
Aug 10, 2010
I'm trying to add 3 additional HDs to my system for storage, using RAID 5 configuration. However, when I set the PCH SATA Control Mode option to RAID(XHD) (in order to enable the motherboard RAID controller) in my BIOS, I get BSOD for a milisecond during the windows 7 loading and then the PC is restarted automatically.
My system spec:
Intel CPU i7 2.66MHz, 8GB RAM DDR3 1333MHz
GigaByte's Motherboard - GA-P55A-UD3
1 x WD3000HLFS-60G6U2 ATA Device (1x300GB)
3 x ST3500418AS ATA Device (3x500GB)
1 x HL-DT-ST DVD-RAM GH40L ATA Device
Windows 7 Ultimate, 64bit
Drives connection configurations:
SATA2_0: ST3500418AS
SATA2_1: ST3500418AS
SATA2_2: ST3500418AS
SATA2_3: N.C.
SATA2_4: DVD-RAM
SATA2_5: WD3000HLFS (System HD)
GSATA3_6: N.C.
GSATA3_7: N.C.
View 5 Replies
View Related
Sep 10, 2012
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
View 9 Replies
View Related
Nov 25, 2009
I am about to acquire a couple (or more) SSD's for an ultra-fast and spacious enough SATA RAID array. Right now I'm thinking RAID 0.
Thing is, I heard by some people that Win7 can't boot from a SATA RAID 0 array, although I am unclear as to whether that is from ALL SATA RAID 0's, or just a few, or an installation error from the users claiming this.
I also haven't found any compatibility lists, which leaves me completely in the dark.
If Win7 can't boot from SATA RAID 0, can it boot from a hardware SATA RAID 5? I'd imagine that any hardware RAID solution would be OK?
View 4 Replies
View Related
Mar 30, 2012
I just changed my disk setup from:
1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
View 8 Replies
View Related
Nov 19, 2011
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
View 1 Replies
View Related
Nov 24, 2009
Does anyone know where I might find the 64 bit ".inf" drivers for Windows 7 64 bit?
View 3 Replies
View Related
Sep 27, 2011
My SSD main drive is running low on space .My motherboard supports 2, SATA3 connections.My current drives are SATA2 SSD main drive and a SATA3 1TB media drive.If I were to add 2 SATA3 SSD's in RAID, does that use up both the SATA3 ports on the motherboard? or do they just combine and use 1?
View 1 Replies
View Related
Nov 26, 2009
I need Download SATA Raid Mother ASUS A7N8X-E Deluxe, for Windows 7 Ultimate.
Answer:-
http://support.asus.com/download/download.aspx?SLanguage=en-us
So go to the above link of Asus website and download it? If there are no Windows 7 specific drivers available, download the Vista drivers.
View 2 Replies
View Related
Jun 23, 2010
[code]...
So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed."
So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks.
View 3 Replies
View Related
Jan 15, 2013
Not wanting to use dual-booting - will I have problems switching SATA connections to run Win 7 Pro from a recently installed SSD and then from a HDD? This until I am satisfied with the transition to the SSD.
View 5 Replies
View Related
Oct 23, 2011
Can I plug-in (and -out) a SATA cable (to hard disc) from (ASUS) motherboard slot when computer is running?
Or will this cause a damage to hardware?
View 2 Replies
View Related
Aug 21, 2009
Just putting together a list for my new October build for the Windows 7 launch and am going to go with a "Raid 1" set up using 2x wd caviar black 1tb drives.
I have not gone down the raid route before but understand that raid drivers needed to be loaded by floppy during installation.
I was hoping not to have to buy a floppy drive so wanted to know if in Windows 7 USB support was available during install to allow raid drivers to be installed from a mem stick when prompted??
View 4 Replies
View Related
May 18, 2011
So i would like to buy a whole new computer. but i want to keep the operating system which is windows 7 professional. It's installed on the hard drives as raid 5. now i know that the raid key or whatever it's called is stored int he bios so just plugging the hard drives into a motherboard that supports raid 5 won't work. So what can i do to install everything that i have on these hard drives into a new system? Also the operating system is registered online would i be able to re register it or something? i don't have the new computer yet i'm just looking around for something good and for a good deal.
View 12 Replies
View Related
Nov 13, 2009
I installed a Rosewell RC-217 Raid card (Silicon Image Sil 3124 SoftRaid 5 Controller-- in Device Manager). The card installed well in Windows 7 64 bit. No problems in device manager.The problem starts when i plug the drive in then rebooted. The boot stops at the 'Starting Window' and hangs. If i boot into windows then plug the drive in all work well. Windows sees the drive and i gave it a drive letter. works great.Problem is i can't boot my system without un-pluging the drive.
View 6 Replies
View Related
Jul 8, 2012
I have a problem, I need to temporarly get a Sata III installed in a AMD Athlon 64+ 4000+, when it is installed the computer doesn't boot when it's not installed (attached to the motherboard SATA port) the computer boots fine, my guess is that the motherboard can't handle these types of SSD, right or wrong ?
View 3 Replies
View Related
Jun 1, 2012
No success getting windows 7 to install with 2 TB sata hard drive. It reads on BIOS but when installer setup for W7 it stops in the beginning with "required cd/dvd driver missing"; asking you to go ahead and remove your installer disk for that particular step only.
View 1 Replies
View Related
Dec 13, 2011
I have two laptops - a new one with Win 7 HP 32bit and an old one with Win 7 HP 64 bit
The new one with Win 7 HP 32bit came with 4gb of ram which is a bit silly since 32bit Win 7 HP can only use 3gb of that, but from what I understand, the serial on the underside can also be used to activate the 64bit version, which would recognise all the ram
Now, even though I've paid for two Win 7 HP licenses, I don't actually have a Win 7 disc, only the factory reset discs (which I had to burn myself when I first turned on the computer - which is pretty shocking really!!!)
But I digress. Is there any way Win 7 HP 64bit on my new laptop WITHOUT paying for it (again) I know XP let you make custom (slipstreamed) XP discs from installations but I can't find a way to do it in Win 7
View 9 Replies
View Related
Apr 30, 2011
There is some debate in my class about if one can put an upgrade disc on a new hdd? Where there is no recent OS installed at all.
View 9 Replies
View Related
Jun 14, 2010
I have a portable with windows xp installed on together with pointsec security software. I decided to install windows 7 on an external e-sata harddisk to keep my work harddisk (xp) apart from my personal harddisk (windows 7).Now I can't boot anymore with the internal windows xp because windows 7 seems to have overwritten some boot files on the internal HD altough I did tell windows 7 to only install on the external HD. I guess that windows 7 installs it's bootloader on the internal harddisk.How I can I restore the original bootloader to the internal HD? Please note pointsec security software was installed on the internal harddisk.
View 4 Replies
View Related
Dec 18, 2012
How can I uninstall a Gigabyte raid contoller without crashing my Win 7 OS? Uninstall is being prevented because "the OS is on the contoller"! Win 7 64 bit is on a Crucial SSD boot drive and AHCI is set in BIOS. However the raid controller is setting all internal drives to SCSI!
View 1 Replies
View Related
Oct 16, 2011
I have installed new windows 7, on my previous windows 7. Till that, I have saved my important files in Local disc D. Windows is installed on local disc C. But previous windows version moved moved to D disk. And my files, that were in D disk, have lost. What can I do for moving back my files, which are very important for me??
View 9 Replies
View Related
Apr 12, 2012
I bought a HP Laptop with Windows 7 Home Premium pre-installed. I got rid of any bloatware and as I'm typing this, Macrium is imaging my C drive to a network drive. Now my question is, would I be able to completely format the computer, set up my own partitions and install Windows on one of them? Preferably a fresh and clean version but I wouldn't mind the bloatware one either. Things to consider, I don't have a disk-drive so it'd have to be done with a thumbdrive; I have not been able to find the actual O/S product key, if someone could tell me where to locate it.
View 4 Replies
View Related
Oct 28, 2009
I had to move the hard drive that I installed W7rc on to a SATA port that is configured in the BIOS as a raid. Now it will not startup because it needs the raid driver installed.
How can I install that driver?
I have tried "Startup repair" and it tells me it can not fix the problem. I tried to do an upgrade and you all know what it said. Must boot into that os first then do the upgrade.
View 9 Replies
View Related
Jan 4, 2012
I have Ubuntu installed on my laptop, but I wanted to install Windows 7 alongside Ubuntu.While trying to install Windows 7 from a CD, I got an error along the lines of: "Windows 7 cannot be installed on disc 0 partition 1".
View 4 Replies
View Related