So i would like to buy a whole new computer. but i want to keep the operating system which is windows 7 professional. It's installed on the hard drives as raid 5. now i know that the raid key or whatever it's called is stored int he bios so just plugging the hard drives into a motherboard that supports raid 5 won't work. So what can i do to install everything that i have on these hard drives into a new system? Also the operating system is registered online would i be able to re register it or something? i don't have the new computer yet i'm just looking around for something good and for a good deal.
I'm in a bit of a predicament. I have a operation of servers which are all the same model (HP DL140) The units don't have an optical drive, so a CD installation is not one of the options. I fiddled around with the bios to attempt installing from USB, but I didn't have any success at that either. The bios of these units are very fickle and very uninformative. I'd prefer to simply access the boot menu and select the USB, but I haven't a clue which key brings up the boot menu. So, I tried my hand at a different method. I took the harddrive of a server with a working OS and popped it into a server which did not have an OS. To my surprise, it booted normally. So this brings the question: Maybe I can just copy over the files of a working server onto the harddrive of another? I'd imagine since the files transferred over are literally the same, there shouldn't be any problem.
We have two disks in raid 0. We want to get rid of them, as they are failing and install a single hard drive with Windows 7. We currently have Vista installed. There are no files I need to copy, just want to start with a fresh operating system. How do I go about this? Can I just remove the old hard drives and replace with the single hard drive and install Windows 7 on it, or is it more complicated than that?
I'm working on a computer with a RAID setup. It is 2 hard drives 500gb each showing up as 1tb in windows. Both drives show up in the bios but all of a sudden when trying ot start the computer I get a "Operating system is missing" error.
I'm trying to run a chkdsk form a win 7 64 bit disk and telling it to run on H; (system drive) but it says 'cannot open volume for direct access'.
The other drive, C: is just a recovery drive built into dell computer systems. I tried using a boot cd and running mbrfix to no avail.
I use drive 'C' as OS' drive and install all the other software on drive 'D'. I use a lot of softwares so if my system crashes I do have to install all the softwares. I want to backup my operating system as well as drive 'D' and when I recover my system it should install OS plus all the softwares.
Can I install upgrade 7 Home Premium edition onto a pc with no operating system installed providing I have the disc that it upgrades from ie xp pro or home etc / anyone tried this ?
I have recently reinstalled my operating system. Once formatted, I installed all the drivers, utilities for my motherboard and graphics card.I now have no sound, even though the RealTek audio driver is installed.I have gone into 'device manager' right clicked to check for updates and Windows advise me that my drivers are up to date.There is an 'x' on my audio icon stating "No Speakers or Headphones are plugged in" and i know my speakers are plugged in and working as i tested them on my ipod. My PC is recognising the input jack, as a window pops up.
I have an Asus Rampage IV Extreme Motherboard and have Windows 7 Installed on a 96gb kingston ssd.
I now bought 2x 256gb Samsung 830s and want to run them in raid. If I set my RAID in bios, I cannot boot into my kingston ssd, it blue screens. If I set it to AHCI I cannot run my ssds in Raid.
I can do a fresh install on the ssds but how do I move my programs and data over? BTW.. I have Norton Ghost 15 which was provided with the Sammy 830s...
ASUS P7P55D-E EVO 2X80gb Western Digital SATA Drives 2x2TB Samsung Spintpoint SATA Drives
I have already been using the machine with another 80Gb Western Digital SATA Drive with Windows 7 Pro 64Bit installed and now want to convert to RAID 5 for redunancy in case of Drive failure (We all say we will back up but we are all lazy when it comes to it LOL).I have taken out the original OS drive and plugged it into the E-SATA connector on the MOBO, gone into the BIOS, turned on RAID for the SATA Ports on the MOBO, and connected the 2 X 80Gb Boot drives. Entered the Hardware RAID Controller POST, and created the RAID 5 Volume from the 2 X 80Gb Discs.Now boot with Acronis Wester Digital edition.Clone the Original 80Gb Disc to the new Raid Array.Shut machine off, remove original OS 80gb Disc from E-SATA port.Boot machine.It starts to boot, and gets as far as the Windwos 7 Microsoft 4 Colour logo and then I get an error and then have to boot into Windows 7 from DVD and go through the repair process.When the Repair has run it reports the following:
The following startup option will be repaired:
Name: Windows Boot Manager Identifier: {9DEA862C-5CDD-4E70-ACC1-F32B344D4795}
The following startup options will be added:
Name: Windows Recovery Environment (recovered) Path: Recoverye52d0bc2-1f15-11df-af10-d764fe3715b8Winre.wim Windows Device: Partition=D76190 MB)
A copy of the current boot configuration data will be saved as:C:BootBCD.Backup.0001 However it fails to do the update How do I get this RAID to boot successfully? I *don't* want to have to re-install the Operating System as that is just too painful a thought?
Ran F12 to regain Operating system - long version. Says computer passes everything but there's no operating system found. Did this Twice. Tried "Operating System" CD that came w/ Studio 17 laptop. Hit option to run via CD & never got anywhere after an hour. Tried Reinstall Hardware disk that came w/ laptop. It shows Vista, but laptop came w/ Windows 7. See where it shows the system's checking things out, but never get anywhere.
Just putting together a list for my new October build for the Windows 7 launch and am going to go with a "Raid 1" set up using 2x wd caviar black 1tb drives.
I have not gone down the raid route before but understand that raid drivers needed to be loaded by floppy during installation.
I was hoping not to have to buy a floppy drive so wanted to know if in Windows 7 USB support was available during install to allow raid drivers to be installed from a mem stick when prompted??
I installed a Rosewell RC-217 Raid card (Silicon Image Sil 3124 SoftRaid 5 Controller-- in Device Manager). The card installed well in Windows 7 64 bit. No problems in device manager.The problem starts when i plug the drive in then rebooted. The boot stops at the 'Starting Window' and hangs. If i boot into windows then plug the drive in all work well. Windows sees the drive and i gave it a drive letter. works great.Problem is i can't boot my system without un-pluging the drive.
So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed."
So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks.
Loading Windows 7 on a new computer. Trying to sort out this raid issue. Computer is :
Gigabyte GA-EP45T-Extreme Processor : Intel Quad Q9400 LGA775 Ram : 4gb Hard Drives : 3 x 1 Tb Seagate Video Card : Radeon HD 4890
I've enabled the raid 5 in the BIOS. I've downloaded the driver from the Gigabyte Disc onto a flash drive. When I load Windows 7 it says " Windows cannot be installed to this disc. This computers hardware may not support booting to this disc. Ensure that the disk's controller is enabled in the computers BIOS menu". I've checked and rechecked the BIOS. I also downloaded the MSM64 Driver in the Gigabyte disc and that the one I copied to the flash drive.
How can I uninstall a Gigabyte raid contoller without crashing my Win 7 OS? Uninstall is being prevented because "the OS is on the contoller"! Win 7 64 bit is on a Crucial SSD boot drive and AHCI is set in BIOS. However the raid controller is setting all internal drives to SCSI!
Suddenly my Win 7 Home Premium x64 will not boot. The system starts, POSTs then loads the DVD driver, then the screen goes black (not blank but "lit up" black if that makes sense). Then nothing. If I use Hiren's boot cd I can boot up using the "boot from HDD" option fine and Windows operates normally. System restore to a previous configuration made no difference to the original problem. I cannot boot into Safe Mode. F8 just offers me boot order options.
- Running the Windows 7 DVD I find: "No operating system is listed on the Repair Windows option." - Running Startup Repair finds the following error: "the partition table does not have a valid system partition" which it claims to have repaired, but the error remains and Windows will still not boot.
I followed this advice: Boot 7 dvd to system recovery options command prompt. Type: Diskpart list vol (find the vol letter e.g C or partition number e.g. 1 for the system partition ) Sel vol C ( or sel vol 1, obviously use the correct letter or number) act exi
My system partition was easily identified and listed as healthy so I selected it and made it active. The problem still remains exactly the same. My system is self built just over a year ago, to my knowledge has been running fine, without any hardware issues. I'm prepared to do a clean install if that's what it takes but if there is a way to fix the partition problem without that I'd like to explore it first.
"Missing operating system" massage is coming when i start my system and i am not able to start. I think because , i had given "mark partition as active" option for one hard dive (E) in disk management when last time i opened. it did not have any data. i did not know, this will make any problem. Now i am not able to boot windows re installation dvd also. i can only take BIOS settings.
"Missing operating system" massage is coming when i start my system. I think because, i had given "mark partition as active" option for one hard dive (E) in disk management when last time i opened. it did not have any data. i did not know, this will make any problem. Now i am not able to boot windows re installation dvd also. i can only take BIOS settings.
I am looking to upgrade my desktop from an xp to 7. System builders are very cheap which concerns me. What is the difference from a system builder and the regular version.
whenever i boot my pc i starts making sounds for like 15 secs and later asks me t choose my operating. this started wheni removed my battery for like 3 weeks and then inserted it back. am using acer mini.
I have a new PC (HP) that came with an OEM version of Win 7/64, I also purchased an SSD that I had planned to use for a boot disk with all libraries on a second 1TB HDD.
I successfully installed Win 7 on the SSD and was happy for a bit, until I discovered some instabilities. Long story short, HP does not release the drivers for their in-house products and I could not stabilize the system, so I moved the SSD to Drive D and re-installed from the factory image. All the drivers I need are there and system is 100% stable.
is there a way to move the System partition over to the SSD so I get the 10 second boot that was so nice?
My system CPU fan remains at high speed and the system won't enter BIOS. I got a duplicate HP system and tried to move my Windows 7 HD from the older system to the new one without any luck. Apparantly Windows 7 is protected with some sort of hardware hash. I can't use repair or restore.How can I get my Windows 7 HD to work in this new system? Everything is legit regarding my software keys, etc.
is it possible to move my Windows 7 system HDD from old PC (which is dying) to new PC, which has better processor, RAM etc?I am thinking that if I uninstalled all hardware before shutting down the system, then putting the drive into new PC it might work.
I have a laptop and I partitioned "C" into "C" and "F". Now I want to move the non-system, non Windows OS files to "F". I need to know which of the folders now on "C" I can move. I've attached a screencap. Which of the folders can I move?I guess I should not moveProgram FilesProgram Files (x86)ProgramDataTemptmpWindowsWindows.oldwinpe_x86Link to Screencap: IMG]http://s1.**************/1p0c1hi10/C_Disk_Folders_2010_12_09_v02.jpg[/IMG]
I'm currently using Windows 7 Professional and have 4 internal HD's set up in RAID. Current Setup: 2 - 500GB drives in RAID 0 2 - 500GB drives in RAID 1
I use the RAID 1 drives for backup purposes only. I have 3 partitions on Raid 0, named as follows: A:,B:,C: I have the OS (Windows 7) installed on C: partition and use the other two partitions on RAID 0 for data. Future Setup: I have just bought the Intel X-25 120GB SSD and would like to do a clean OS install on the SSD and still keep my RAID 0 and RAID 1 setup for other data.
Here's my question: 1. How can I install the OS on SSD without disrupting any data on the RAID 0 and RAID 1 HD's?
I would like to be able to install the OS on SSD and still have access to the data on my previous C: drive on RAID 0 (including the OS data). I want to delete the OS data on the RAID 0 HD from within Windows(on SDD) if that makes. Will that be possible?
I'm afraid of losing my RAID drives/data. I have read that I should unplug the RAID drives before I install Windows on SDD and then re-plug them again. Is there a particular order I should do that in? Will the BIOS recognize the old set up if I unplug/re-plug the old drives? way to install Windows on the single SSD without losing the existing RAID 0 & RAID 1 setup and data.
I have a smooth running Windows 7 system. I want to convert it to a Raid 1 system. I have a ASUS Rampage Formula motherboard with a Intel X48 chipset and ICH9R installed. It has 4gb memory, Core 2 Quadand a WD 640 gb drive. I have purchased another WD 640 to setup the Raid 1 array. I cannot find anyone who has installed it on a running system, they all build a new system. Can you install Rain 1 on a running system? If so how do you do it?
My system disk is about 80% filled up and I am looking to move the system files to a new disk for increased efficiency. I believe the way to go is diskcopy, creating a clone of current system disk to a new disk.smI am looking at EaseUS Disk Copy Home Edition 2.3.1 and MiniTool Drive Copy both freeware.
I was just wondering is there anything within the fabric of your p.c. (the p.c. equivalent of a clothes label) which specifically states its operating system.I have Windows and Windows Office 2007, but as I said, is there anything that clearly stipulates on my hard-drive which operating system I am using.
I had Dell XPS 8300 Desktop & had bought & Installed Windows-7 ( Ultimate ) on it's 500 GB HDD.I gave that system to my relative except Hard Drive.Now I bought Dell T-7500 Workstation with only DOS installed on it's hard drive to save some money & because I already have Windows-7 ( Ultimate ) DVD.I took out the hard drive with DOS from the workstation & replaced it with the hard drive that I had in XPS with Win-7 already installed.I then tried to boot it in the workstation but it wouldn't boot & gave error messages.So I formatted the OS Partition & fresh installed Windows-7. Now it does load Windows -7 but first it goes thru some other commands as follows when I start the system.
Dell SAS 6 Host Bus Adapter BIOS MPTBIOS 6.22.03.00 ( 2008.08.06 ) Initializing..... Press Ctrl - C to run SAS Configuration Utility Searching for Devices at HBA 0..... Dell MPT Boot ROM Successfully installed
Then it loads Windows-7.All of above happens on its own, I didnt touch anything.So what is going on & what do I have to do get rid off those initializing commands ? I have never had this happen to any previously owned Dell systems.Also I haven't installed any drivers yet but Sound, Video & Internet does work.Do I need to install any drivers & if yes, which ones ?Here is the configuration of Dell workstation T-7500 :
Intel(R) Xeon(R) E5645 2.40GHz, 12M cache, 5.86 GT/s QPI, Turbo, HT, 6C Intel(R) 5520 Chipset DOS Factory Installed (English) Integrated Intel(R) SATA 3.0Gb/s controller with support for RAID Integrated High Definition Audio