Raid Card Will Not Boot With Drive Installed
Nov 13, 2009
I installed a Rosewell RC-217 Raid card (Silicon Image Sil 3124 SoftRaid 5 Controller-- in Device Manager). The card installed well in Windows 7 64 bit. No problems in device manager.The problem starts when i plug the drive in then rebooted. The boot stops at the 'Starting Window' and hangs. If i boot into windows then plug the drive in all work well. Windows sees the drive and i gave it a drive letter. works great.Problem is i can't boot my system without un-pluging the drive.
View 6 Replies
ADVERTISEMENT
Jun 4, 2012
My win 7 machine boots perfectly with two SATA mirrored drives and a Promise Ultra 133 TX2 IDE controller card with no drives attached. But when I connect drives to either IDE1 or IDE2, the machine will not even get to win start up.
View 1 Replies
View Related
Aug 24, 2012
I need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies
View Related
Jun 21, 2011
I have an XFX motherboard (x58i), model # MD-X58I-CH09. It has three PCIe slots. I have an Nvidia GEForce GTX 260 graphics card in one of the PCIe slots (middle of the motherboard). This is running two 22" displays with no issues at all.
I also have a Asus ENGT430 video card with HDMI output that I want to load into one of the other PCIe slots. When I do this, the computer will not boot properly. It starts (displays the splash screen for windows7), but after that it appears as if there is some sort of conflict. Probably a driver conflict but I cannot even see anything or log in to the PC. Will the mother board support two different graphics cards? If so, what do I need to do to get it to work. I have not installed any drivers for the ASUS graphics card because the instructions have you do this after booting. With Windows7 I didn't think I would have to install anything.
View 8 Replies
View Related
Jul 16, 2012
I have set up a dual boot- Windows 7 pro & XP ultimate, both on separate SSD's, all OK. I also have two 3TB HDD's set up under windows 7 RAID, all OK. In XP under drive management the RAID drives show up twice, once as 775GB unused drives with no drive letter allocated and also as 2.7GB RAID drives with status 'failed', drives marked as 'missing'. Is there a way I can get the RAID drive accessible under XP?
View 8 Replies
View Related
Mar 5, 2012
I have 2 SSDs each partitioned into 80GB and 40GB like this:
-Drive1-80GB (boot) and Drive1-40GB
-Drive2-80GB and Drive2-40GB
Drive1-80GB is already the Windows 7-64 boot partition for the system. Can I configure a software RAID-0 with Drive1-40GB and Drive2-40GB? I know this is unorthodox but I wanted to try this for a few reasons.
View 4 Replies
View Related
Mar 31, 2011
My system was working fine last week until I've installed an additional SATA HDD, windows will boot up until the windows 7 logo after that its all black screen, I've waited for hours for some response to happen but nothing happened, I've reformatted it a few times with the same outcome. I've tried resetting CMOS a lot of times but to no avail. But this evening I tried taking out my Graphics card and other peripherals and then windows boot! it boots with all other accesories(wifi card,firewire etc.) and the new HDD but when I try to reinstall the Graphics card it goes back to a black screen after the windows 7 logo!! is it a case of a busted video card? if so then why does it have display? I also checked the back of the Graphics card's heatsink and it has this white paste-like goo that has hardened, should i clean it and apply new thermal paste?
View 14 Replies
View Related
Oct 26, 2011
I've been trying to upgrade an old coimputer to run Windows 7, so far it works really great, but the intel graphics are really shitty, so I bought an EVGA GeForce 6200 256MB PCI card to install. problem is, whenever the card is installed the computer won't boot, and is stuck on this screen,I pulled out the CMOS battery to try to reset it, but no dice.
View 4 Replies
View Related
Sep 30, 2012
I have a 1T SATA system drive and a 1T SATA working drive. I installed a 3T SATA storage drive, and now my system won't boot from the C:. I have to go into the BIOS and boot from there, or use a boot disk. How do I get the system to boot from C: again?
View 3 Replies
View Related
Mar 23, 2012
I have a partition question and after scouring the Web, can't find anyone with the exact same situation as mine. Basically what I'm wondering is if I can delete a primary partition and then extend another, non primary into that space.
Here's what I have and why I want to do this: my laptop came from the factory with one 500GB SATA drive, split into two partitions (C, primary, and D, logical, each 250GB). The Win7 install was on the C drive. Recently, I installed a 120GB SSD as a second drive, and using the tools with it, copied the contents of my existing C partition to the new SSD, and then made the SSD the boot drive labeled as the C drive. So far so good, everything works fine.
Now, what I'm left with is this: C: 120GB (SSD, now the boot drive with the Win7 install) D: 250GB (SATA, the original D partition, Disk Management IDs it as a logical drive, extended partition) E: 250GB (SATA, the original C partition, Disk Management IDs it as a primary partition)
So, I have the original "C drive" on E now... it's no longer the system/boot drive. Obviously I don't need the files on it as they are all on the new SSD. What I want to do is to delete all those files and then combine what's on D and E into one 500GB D drive as I have no reason to have the two partitions. Is it possible to just delete the E partition and then extend the D partition into the unallocated space? I'm confused because it seems as though the D partition may rely on the E partition being there since the E drive IDs as primary. Or would the D partition become primary?
I know I could just back up the D partition to an external drive, delete both D and E partitions, and reformat as one new D and restore the files, but I don't want to create more work for myself if I don't have to. Obviously I don't want to mess up the files on the D drive though, which is why I'm asking.
View 6 Replies
View Related
Nov 24, 2009
I just installed a new WD 500 GB hard drive into my DELL computer. I am trying to install windows 7 from a dvd but it will not boot. Does anyone know what the problem is.
View 8 Replies
View Related
Jan 6, 2009
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
View 0 Replies
View Related
Dec 10, 2011
I recently bought a new hard drive with windows 7 home premium 32 bit installed. When tried to install it in my pc it would not boot up, I am assuming its because everything is new to it. I bought a windows 7 recovery disc but it has not worked. I did not get an install disc with the new hard drive.
View 5 Replies
View Related
Dec 12, 2011
I have a computer with two (IDE ribbon cable) hard drives. One had a bad windows XP installation on it. I installed Windows 7 on the other. I formatted the drive before installing Windows 7.Then, I decided I want to use the hard drive with the bad winXP installation on it, in another computer (I will format it). When I opened the computer side panel, I wasn't sure which hard drive was which, so I unplugged the power to one, and started the computer.The thing is, it won't boot Windows 7 with either of those hard drives alone, only when both are plugged in. With HD #1 disconnected, it says "Can't find BOOTMGR, press a key to reboot." With HD #2 connected, I get asked whether I want Windows 7 or an older OS, and when I choose Windows 7, I get an error message, something like "Windows 7 failed to start. To try and repair, insert install disc, or use recovery mode, etc" With both HDs, I get asked the same question, "Windows 7 or an older OS," but when I choose Windows 7, it works. In my computer, I have verified that Windows 7's files are on one disk, and corrupt winXP files on the other.
View 8 Replies
View Related
Jan 21, 2013
I have a Machine with the Following Config:
Intel E2180 CPU
2GB Ram
Gigabyte GA-G31M-S2C Mainboard
Seagate ST31000340NS SATA Hard Drive Connected on SATA0
Operating Systems:
Windows 7 Ultimate 64Bit on HDD
Windows 7 Ultimate 32Bit Booting from VHD
I Installed Windows 7 Ultimate 64Bit onto Hard Drive as Per Normal Installation Onto the Hard Drive and Installation created 2 Partitions (1 System PArt and Another for C: Drive) Everything Works Great.m I Then Installed Windows 7 Ultimate 32bit Into a VHD. Setup Created a Multiple Boot Entry into the BCD so that when I Boot it Prompt Which OS I Want, I then Used BCDEdit to Change the Descriptions of the Boot Options "Windows 7 Ultimate - 64Bit - HOST" and "Windows 7 Ultimate - 32Bit - VHD" Everything still works Great.. No Problems.. Been Like this for a While Now and Perfect.
Now the Problem is that I Need to get some Data From and Old SATA Drive. I Shutdown .. Plugin the WD1600AAJS (160GB) into Another SATA Port (SATA1).. Turn Machine on and Press Delete to Enter Setup for Bios.. Goto Set Boot Device Priority and Ensure that the ST1000340NS Drive is at the Top (1st Priority).. Exit and Save Settings.. PC Goes through POST and Then Will not Boot.. it Gives "Missing Operating System" Shutdown Remove WD1600AAJS Drive.. Boots Perfect.. Reattach WD 1600AAJS Drive and "Missing Operating System" Tried Using "F12 to Select Boot Option" during POST to Select Boot Device.. Choose ST1000340NS ... and Still same Issue.. Remove the WD1600AAJS and Boots No Prob Off the ST1000340NS.
I thought that maybe it was the WD Drive.. so Tried another Seagate Drive.. and Same Issue..
I have set Every Available Option on The Bios to Choose the Boot Device and NOTHING Works.. I have Even swapped HArd drive SATA Ports .. still no Difference.
I have an Idea there is a problem with the BCD but I Cannot Edit or Add any thing to the BCD as it will not boot with the second drive attached. And When you edit the BCD it need the second drive attached to be able to Add a BCD Entry.
View 2 Replies
View Related
May 13, 2012
Asus cm5570-ap006 originally running vista premium and owner wanted an upgrade to seven. Bought a new hard drive b/c old one died. Mobo had trouble finding new drive but, after setting bios back to default(F5) it installed and finally got working.Owner gets pc and starts getting blue screening and saying theres an f1 drive error and wont wake up after suspending without reboot.So I get it running fine by removing avg(which is causing blue screen for some reason) and the it is now waking up after auto hibernation. But if you put into hibernation manually it wont wake. I update windows and it goes back to not recognising hard drive.Flash bios remove cmos baterry reset bios to default and set hard drive to ahcpi and it reinstalls fine update windows and it stops working. Use restore point to get it back and running and this time dont update windows and its running ok again. Shut it down for the night and the next day go to boot it up and there is no bootable media and now I am trying to reinstall Windows 7 and after it does it gets a no bootable media error even though it is
View 3 Replies
View Related
Oct 11, 2009
I recently isntalled windows 7 professional and I have three sata drives, one is the system drive where windows 7 is installed (C, my primary partition, the other is a storage drive (F and a drive to replace the partition (Z. My boot priority for the moment is the F: drive then the C:. This is because for some reason my C: drive, even though the system is installed on it, will not boot.
I tried several things like copying the hidden system folder in F:Boot to the C drive but that did not work. I recently did a repair install but that did not restore the boot manager. Is there a way to manually set my C: drive as my primary boot drive, without jumping through hoops, I bought the Z drive to replace the F drive and need to be able to boot without it.
View 3 Replies
View Related
Sep 28, 2012
First, the information as it is. I had a hard drive issue that I'm working on currently, trying to recover I suppose what is a crashed hard drive. There are tons of errors on it, but that's not the question I have right at the moment, but some background.
I have tried to reinstall Windows on a brand new 2.5" Seagate 500GB 7200rpm HDD. I formatted the drive using the windows 7 ultimate installer and booted it using a USB booter made from the windows 7 download tool.
When I booted it up and tried to get it going, it gave me a hardware error saying "Windows wasn't able to configure the hardware and try startup repair" or something to that effect. I read around and it said that since my BIOS says the HD is in raid configuration that it needed some Intel Raid driver, which I installed and tried running, but it didn't seem to work. It says now "windows cannot repair this computer automatically". The problem signature is as follows:
Problem Event Name StartupRepairOffline
Problem Signature 01: 6.1.7600.16385
Problem Signature 02: 6.1.7600.16385
[Code].....
Primary HDD in the BIOS is recognized as 500GB RAID is On as well. Trying to install Windows 7 Ultimate 64 bit.
View 5 Replies
View Related
Aug 21, 2009
Just putting together a list for my new October build for the Windows 7 launch and am going to go with a "Raid 1" set up using 2x wd caviar black 1tb drives.
I have not gone down the raid route before but understand that raid drivers needed to be loaded by floppy during installation.
I was hoping not to have to buy a floppy drive so wanted to know if in Windows 7 USB support was available during install to allow raid drivers to be installed from a mem stick when prompted??
View 4 Replies
View Related
Jul 22, 2012
New to the Tech forum boards but I am having a problem with my HP Pavillion dv6t. The hard drive went bad so I installed a new Seagate 1TB internal hard drive in the notebook. Starts up fine and then it says that "No bootable device found"---insert disk press any key. The disc is in the cd rom, I went into the BIOS enabled the CD/ROM boot option. I also went into the Boot option menu and tried selecting the internal cd/dvd rom drive option and I went into the actual boot order screen and adjusted the boot order so it read the cd-rom drive first then the hard drive. I also am using the HP Application and Driver recovery DVD. I am not sure if the disc is bad or cd drive is bad. The other thought is that because it is a brand new hard drive there is no information on it for the drivers so maybe the computer is not processing the information.
View 8 Replies
View Related
May 18, 2011
So i would like to buy a whole new computer. but i want to keep the operating system which is windows 7 professional. It's installed on the hard drives as raid 5. now i know that the raid key or whatever it's called is stored int he bios so just plugging the hard drives into a motherboard that supports raid 5 won't work. So what can i do to install everything that i have on these hard drives into a new system? Also the operating system is registered online would i be able to re register it or something? i don't have the new computer yet i'm just looking around for something good and for a good deal.
View 12 Replies
View Related
Jun 23, 2010
[code]...
So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed."
So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks.
View 3 Replies
View Related
Dec 30, 2009
Loading Windows 7 on a new computer. Trying to sort out this raid issue. Computer is :
Gigabyte GA-EP45T-Extreme
Processor : Intel Quad Q9400 LGA775
Ram : 4gb
Hard Drives : 3 x 1 Tb Seagate
Video Card : Radeon HD 4890
I've enabled the raid 5 in the BIOS. I've downloaded the driver from the Gigabyte Disc onto a flash drive. When I load Windows 7 it says " Windows cannot be installed to this disc. This computers hardware may not support booting to this disc. Ensure that the disk's controller is enabled in the computers BIOS menu". I've checked and rechecked the BIOS. I also downloaded the MSM64 Driver in the Gigabyte disc and that the one I copied to the flash drive.
View 5 Replies
View Related
Dec 18, 2012
How can I uninstall a Gigabyte raid contoller without crashing my Win 7 OS? Uninstall is being prevented because "the OS is on the contoller"! Win 7 64 bit is on a Crucial SSD boot drive and AHCI is set in BIOS. However the raid controller is setting all internal drives to SCSI!
View 1 Replies
View Related
Nov 23, 2009
I'm installing Win7 64 on a single system drive but I plan to add a 3rd party RAID controller and drives for data storage. Do I need to hook up the card and storage drives and install the drivers on the initial install of Windows or can I simply install the OS on the main system drive and add the RAID at a later point?
View 2 Replies
View Related
May 30, 2011
need drivers for ultra ata/133 pct raid card for window 7 pro
View 1 Replies
View Related
Nov 12, 2009
I just bought a Via sata card to use with my disks. The problem is that i can't get it to work.
When i install the card it seems to get installed fine in the device manager and with the raid configurerer application that went with the driver.
But the card just doesn't recognize any harddisks. There's no change when plugging a harddisk in it. The application also seems to think that there's 4 channels on the card(there are 2) and they all show as a big red "?".
I've looked everywhere for a driver, and the newest one is a part of the old via chipset driver: 'VIA_HyperionPro_V524A'
Is it a proper Windows 7 driver i need ? and are there such?
View 2 Replies
View Related
Dec 26, 2010
My PC is setup with two hard drives as RAID-0 (1 partition) and it has refused to boot Windows 7 for the past few days. The computer simply shows a black screen after it goes through the BIOS screens. Pressing F8 to enter Safe Mode does not work at all.This issue has arisen after I tried installing a video card (XFX Geforce 8800 GTX) without uninstalling my old video drivers. It's still a mystery to me how installing the card would cause problems with Windows or my hard drivesHere's what I've done so far to troubleshoot:I created a System Recovery boot disk because I lack the original Windows 7 installation cd. System Restore does not work, nor does the Image function. System Repair simply hangs for an unbelievable amount of time.
After scanning my hard drives for various info, I found out that my first hdd is listed as NTFS, yet my second one is RAW. Subsequently, the C: drive is also listed as RAW, and I cannot use Chkdsk.exe on it. Through a cmd prompt, I used Bootrec.exe /FixMbr and /FixBoot, but it did not seem to fix the issue. I also used Bootrec.exe /ScanOs to see if the Windows 7 installation still existed, yet it came up with nothing.I've managed to use a program called RAID Reconstructor, via a PE Builder boot disk, in order to copy all my hard drives' sectors over to my external hard drive. The external is now hooked up to a second PC that I'm using to troubleshootIt seems that all of my personal files are intact and working perfectly fine, and the file names are also correct. I don't really know how to check my Windows/System32 files for corruption.I'd like to fix Windows 7 without having to format the hard drives. Since I lack the Windows 7 installation cd, I can only install Windows XP while lacking 64-bit support. Since I'd like to avoid this, I was wondering if there was a way to get Windows 7 back up and running. But I suppose this isn't possible without getting my second hdd back to NTFS format.
View 2 Replies
View Related
Feb 18, 2012
my goal is to boot windows 7 x64 with raid-1. My boot drive is a SSD, which is not part of the raid array. I have 3 seagate ST2000DM001 that I want in raid-1. I have tried installing windows 7 with ahci in bios first but no luck. I was able to boot from raid1 when I started bios out in raid but my ssd drives read/write speeds significantly decreases.
View 3 Replies
View Related
Jan 9, 2013
I purchased 2 500gb hdd's for a raid 1 setup. I already have a 128gb SSD with my operating system that i plan to leave untouched. i simply want to install games onto the hard drives in raid 1.
I have an m5a99x evo motherboard by asus. My problem is that whenever i turn on the raid in bios, press control+f, and set the 2 drives in raid 1, windows 7 cannot boot. If i select the restore, i cannot access my system image from my external hard drive and it cannot solve the problem on its own.
View 2 Replies
View Related
May 9, 2012
in my PC there are some drives with RAID0 arrays and from little time I have bought a SSD for Operative System (Windows 7).in your opinion (on the BIOS) is it better making the Boot with SSD or with another drive with RAID0?
View 9 Replies
View Related