I have a problem, I need to temporarly get a Sata III installed in a AMD Athlon 64+ 4000+, when it is installed the computer doesn't boot when it's not installed (attached to the motherboard SATA port) the computer boots fine, my guess is that the motherboard can't handle these types of SSD, right or wrong ?
View 3 RepliesThe other day I went to restart my computer, on restart it showed the motherboard info for longer than usual maybe 10-20 secs then proceeded to boot windows. About 2-3 days later I was doing a few things, computer froze so I manually had to shut off and turn back on the computer and it would show the motherboard information and not do anything from there just sit there. Tried to boot again maybe 3 times and nothing changed. Everything powered up fine ect ect. Took the case off looked at a few things, everything looked fine. Turned it back on and it booted right away like normal. Didn't have the keyboard plugged in so I had to restart again and was going to anyways to see what it would do and it booted just fine again.
View 2 Replies View RelatedI've got a Dell Insprion 1470 and it never worked right (I would return it for a new one but first Freak Squad has to "fix" it).When booting it will sometimes freeze at the windows logo, just go black, go into start up repair, go into safe mode, all kinds of stuff.I have ran many tests/programs and they all say nothing is wrong.
-sfc /scannow
-chkdisk
-start up repair
-memory test/diagnostics
I've updated BIOS and all drivers, Ive defragged and ran CCleaner.I ran the full system scan in Dell Support Center.
So each time I start up my computer, my mouse, keyboard, and headphones getrecognized. My mouse is the only device of those 3 to use usb. My blue snowball microphone and my hawking directional antenna don't get recognized until I unplug them and plug them back in. It take 2-4 times of unplugging and plugging in for it to recognize my snowball.
View 2 Replies View RelatedI just installed windows 7 on my 64gb SSD sata3 hard drive i did a clean install. Now my 1TB Hard doesnt show up in windows. It shows it in the bois and in the device manager but thats it....
View 1 Replies View Related...every time I boot my system, Windows says it is installing the SATA driver. BIOS entries are OK, once drivers are installed, Disk Management shows everything OK too. So, what could be the cause for this? I have two disks, the System SSD (OCD Vertex II 60GB SATA) must have its driver installed to boot Windows, so the msg must refer to the second HD (Seagate 1TB SATA
View 1 Replies View RelatedNo success getting windows 7 to install with 2 TB sata hard drive. It reads on BIOS but when installer setup for W7 it stops in the beginning with "required cd/dvd driver missing"; asking you to go ahead and remove your installer disk for that particular step only.
View 1 Replies View RelatedToday I booted up my computer and got a screen saying something went seriously wrong with my computer and that I should repair it from an installation disk. I load up windows onto a USB, boot it and click the repair option. It's been about half an hour and nothing has shown up. Is it still loading or perhaps something is very wrong with my PC?
View 2 Replies View RelatedI tried to install Internet Explorer 9 for testing a website. It prompted me to restart after the install, so I did. It never started back up. Now my computer will not boot into windows except in safe mode and system restore doesn't facilitate at all.
This is my ntbtlog.txt:
[code]Microsoft (R) Windows (R) Version 6.1 (Build 7600)
5 29 2011 02:49:09.125
Loaded driver SystemRootsystem32
toskrnl.exe
Loaded driver SystemRootsystem32hal.dll
Loaded driver SystemRootsystem32kdcom.dll
Loaded driver SystemRootsystem32mcupdate_AuthenticAMD.dll
Loaded driver SystemRootsystem32PSHED.dll
Loaded driver SystemRootsystem32CLFS.SYS
[Log] .....
I built a new computer. Rather expensive, but it should perform well. -Anyway-, I bought a brand new hard drive with the expectation of installing windows 7 on it and then working from there. The hard drive is recognized in the BIOS, the CMOS, and anything at all I've checked, but when I put the windows 7 64 bit disk in and try to do a custom install, seeing as I have nothing on the disk from which to upgrade, my hard drive does not show up in the section in which 7 asks where I want to install.
Motherboard is GIGABYTE GA-X58A-UD3R LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard, hard drive is Western Digital Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive.
The hard drive is plugged into the top SATA port (It has like, 10).
What can I do?
Loading Windows 7 on a new computer. Trying to sort out this raid issue. Computer is :
Gigabyte GA-EP45T-Extreme
Processor : Intel Quad Q9400 LGA775
Ram : 4gb
Hard Drives : 3 x 1 Tb Seagate
Video Card : Radeon HD 4890
I've enabled the raid 5 in the BIOS. I've downloaded the driver from the Gigabyte Disc onto a flash drive. When I load Windows 7 it says " Windows cannot be installed to this disc. This computers hardware may not support booting to this disc. Ensure that the disk's controller is enabled in the computers BIOS menu". I've checked and rechecked the BIOS. I also downloaded the MSM64 Driver in the Gigabyte disc and that the one I copied to the flash drive.
Not wanting to use dual-booting - will I have problems switching SATA connections to run Win 7 Pro from a recently installed SSD and then from a HDD? This until I am satisfied with the transition to the SSD.
View 5 Replies View RelatedHP Recovery Manager don`t installed
View 1 Replies View RelatedI have a portable with windows xp installed on together with pointsec security software. I decided to install windows 7 on an external e-sata harddisk to keep my work harddisk (xp) apart from my personal harddisk (windows 7).Now I can't boot anymore with the internal windows xp because windows 7 seems to have overwritten some boot files on the internal HD altough I did tell windows 7 to only install on the external HD. I guess that windows 7 installs it's bootloader on the internal harddisk.How I can I restore the original bootloader to the internal HD? Please note pointsec security software was installed on the internal harddisk.
View 4 Replies View RelatedWhen I try to install java because my browser says it's not installed it says it IS installed. So it asks me if I want to reinstall that's fine too. Then it gives me an error message saying that you can only do that if it's already installed.I can't find folders of it it's not in the add/remove programs list either.
View 1 Replies View RelatedI've installed ASUS Wi-Fi USB adapter (model USB-N13) for LAN. There is Windows 7 Home Premium x64. Through control panel I see that adapter works normally and the drivers are the latest. However my PC doesn't see the adapter - the ASUS utility notices me "ASUS Wireless LAN card is taken apart from your desktop PC".I have the same Wi-Fi adapter at another my PC with Windows 7 Home Basic, and everything works nice. Of course I changed these adapters between my computers. Conclusion is both adapters are working good. The same models, the same drivers. Actually I don't understand where is the mistake?
View 1 Replies View RelatedI just got my new Vantec IDE/SATA to 2.0 USB Adapter installed. I use it on my laptop to give me extra storage space.. or plan to.. this drive already has a good copy of Win 7 installed and i'd like to boot into it from the USB adapter so it will be easier for me to find out what i need to back up.
I did try to boot from USB and windows does start to load then crashes.. I don't know if it's due to the Vantec unit or if I just need to repair the MBR on the drive. The drive has been sitting in a safe place for about 8 months not being used.
After putting in a second GPU -- which now covers 3 of my Sata ports -- I was forced to switch my drive order around. I was able to boot successfully with 2 of them, but oddly not 3. So I removed my System Reserve drive, setting C: to the active drive, figuring that would clear things up. Then plugged in my 3rd drive into that spot leaving just 2 drives, but windows still does not boot.I checked boot order in BIOS, but I still get boot error.Windows will only boot when I remove the drive leaving only the OS drive.I know a reinstall will solve my problems, but I need to avoid that at all costs.
View 7 Replies View RelatedWhen I installed a TF III GTX 570 video card I lost my PCIE-X1 slot and 1 SATA port on the Inspiron 530 Foxconn G33-M03 MOBO I am still running. Now aside from the fact that I need to upgrade the MOBO...
I added a Rosewill RC-209-EX PCI-SATA adapter (SiL3114) to gain back 4 SATA ports. The card is working fine. It is slow compared to the MOBO SATA ports but I expected that. I have a Seagate 500GB HDD and an Optiarc DVD R/W drive attached to it. BUT..... I can not boot from either device. They do not appear in the boot options....
Based on my reading I got the "NON-RAID" (IDE/ATA emulation) BIOS from Silicon Image and flashed the card's BIOS since I will not be using it for RAID. It is just for more SATA ports. Should I be able to "see" the PCI-SATA card and its attached devices in the 530's BIOS Setup Screen? Is it a limitation of my Dell neutered BIOS?
The RC-209-EX documentation specifically states it "supports" CD/DVD drives.
There is plenty written about booting from a RAID array configured to the RC-209-EX but very little about booting from single device.
I've recently purchased two 30GB SSDs which I have set up in a RAID 0 array and I have installed Windows onto these drives. I have a second, 2TB Seagate Barracuda Green HDD that I have used to put my user profiles and additional programs/games on as it wouldn't fit on the SSD.Everything was fine for a few days after installation. Then this morning I rebooted the computer and it just stalled on the flashing cursor (underscore) in the top left corner of the screen. I did the basic fixes (Windows repair, checking RAM) and nothing worked.Then I thought that I should try disconnecting all but the SSD with the OS on it. SUCCESS! It booted to Windows but couldn't find any programs/user data so it created a new "profile". I shutdown the computer and tried reconnecting just the data hard drive.I have two additional hard drives (used for backups) that don't affect anything at all when I plug them in.Does anybody know what could be the problem? I'm at a loss and I need the computer
View 3 Replies View RelatedI am running XP on a SATA HDD. I have installed Win 7 on a second partition with some problems. The main problem was random BSOD's. This I believe, I have traced back to the fact that the MoBo runs Nvidia chips. Have downloaded the updated Nvidia Win 7 chip drivers. So, I uninstalled Win 7 and removed boot loader via BCDEDIT.
What I would now like to try is to install Win 7 on a separate IDE HDD connected to the primary IDE controller. This is so I can sort out the Nvidia driver problem.
I can see problems with this. My questions are the following:
What will I set the IDE HDD to be, Master or Slave? Then boot off DVD/ROM and then install Win 7 as normal onto IDE HDD. If yes, I take it that the Windows 7 bootloader will not be installed on the XP SATA HDD. If this is the case then I should be able to use EasyBCD to add the XP on the SATA HDD. Most critical part of the whole deal will be to set the SATA HDD (with XP) to boot FIRST. I have been down this track before and the MoBo sets the IDE as Drive 0 (FIRST boot HDD).
I know that there is a simple answer to this. I just cannot see the forest for the trees at present.
I recently build a new system with win7 64bit. Everything went well untill I exchanged a blue ray drive with a dvdwriter (1 day later). Win7 recognized the drive in device manager but did not assign a drive letter nor would the drive open (function). After trying everything I can think of I decided to reinstall the sata drivers from the asus websitebecause I wasn't able to use the motherboard disk with the DVD drive for installation) the system restarted and never booted back up. The bios recognize the ssd as 1st boot but win7 does not boot back up. As a matter of fact the hd LED doesnt flash anymore like it did when the system was working. I also could not use 5 USB ports (i was going to reinstall the drivers after the sata drivers) from the beginning of win7 install and Bluetooth comport not available. Did I screw up the bios? (bios flash with USB?)
Win7
Asus rampage iv extreme x79
2x2gb corsair dominator gt 1600
Intel i7 3820
Sandisk extreme ssd 120gb (the only storage media)
Corsair h100 cooling
I know, I know, I know... SATA is Hot PnP. I'm old school and finally gotten over the fear of Hot PnP USB.
I'm replacing a new Windows 7 PC for a customer and the old PC is WXP. Reason being, the old PC Pwr Supply died. Can I take the old SATA HD w/WXP on it and just plug it into a SATA port on the new PC while it's running to copy files from it (safely).
And can I facilitate a Files and Settings Transfer WXP-to-Windows 7 in this manner?
I have Windows 7. My computer keeps crashing I have written down the stop codes, which are all different each time Also keep getting nv7ddmKm.sys.I have scanned the computer with Kapersky and also malwarebytes but both scans are clean.I can be doing anything on the computer when it happens but mainly it is when i am using Adobe CS5 or uploading images onto my computer from Nikon software installed on the computer.
View 14 Replies View RelatedI need to move the sata connection for my drive "D" on the motherboard, however after moving it Windows 7 won't boot.
Gateway LX6820, 8GB Ram Windows 7 HOMEPREMIUM 64 bit Drive "C"- Intel X25V SATA SSD 40GB, has 200MB System Partiton for MBR and the rest is for the OS Drive "D"- WD Raptor SATA 150GB, has User folders, Program Data, and Programs installed
I have a fresh install of Windows 7 HOMEPREMIUM 64 bit that was done with drive "D" in one of the hotswap bays. All my tweaks, and settings changes are done and Windows operates with no problems. Now I wan't to move the drive to an internal bay. The set up and install was done using sata 4 on the motherboard but due to cable routing I need to use sata 2 for the move.
After the physical move and cable change Windows sees the Raptor as drive "E" not "D", it can't access the user profile and loads a default profile instead. This default profile won't allow access to disk management so I can change the drive letter. I have tried using Diskpart to reassign the drive letters but when I boot into Windows it changes it back to "E" again (must be due to the sata port 2 being assign "E" in an earlier configuration?). I tried using Windows repair but it changes the boot sector to"C", the "C" drive to "D" and the Raptor to "E", had to change the cables to the original locations and do a system restore to fix that one.
A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.
View 9 Replies View RelatedHow do I set up a Windows 7 System with a SSD boot drive but with all User, Data & Programs (including Games) "Automatically" installing to and run from, an internal SATA Hard Drive, that preferably is labeled "C" drive or get as close to that as possible?!
View 1 Replies View RelatedI need to move the sata connection for my drive "D" on the motherboard, however after moving it Windows 7 won't boot.
Gateway LX6820, 8GB Ram
Windows 7 HOMEPREMIUM 64 bit
Drive "C"- Intel X25V SATA SSD 40GB, has 200MB System Partiton for MBR and the rest is for the OS
Drive "D"- WD Raptor SATA 150GB, has User folders, Program Data, and Programs installed
I have a fresh install of Windows 7 HOMEPREMIUM 64 bit that was done with drive "D" in one of the hotswap bays. All my tweaks, and settings changes are done and Windows operates with no problems. Now I wan't to move the drive to an internal bay. The set up and install was done using sata 4 on the motherboard but due to cable routing I need to use sata 2 for the move. After the physical move and cable change Windows sees the Raptor as drive "E" not "D", it can't access the user profile and loads a default profile instead. This default profile won't allow access to disk management so I can change the drive letter. I have tried using Diskpart to reassign the drive letters but when I boot into Windows it changes it back to "E" again (must be due to the sata port 2 being assign "E" in an earlier configuration?). I tried using Windows repair but it changes the boot sector to"C", the "C" drive to "D" and the Raptor to "E", had to change the cables to the original locations and do a system restore to fix that one.
Can I plug-in (and -out) a SATA cable (to hard disc) from (ASUS) motherboard slot when computer is running?
Or will this cause a damage to hardware?
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
I have XP (x86) installed on one partition.
Last night I installed Windows 7 (x64) on a separate partition.
Anytime I had tried this in the past, using Vista, it always detected the Windows XP partition, and gave me a boot menu with "Earlier Version of Windows" option to boot to.
This is not so with Windows 7.
How can I get the boot menu to show both options, to boot to XP or to Windows 7?