Win7 Doesn't Recognize SATA Hard Drive

Jan 30, 2010

I built a new computer. Rather expensive, but it should perform well. -Anyway-, I bought a brand new hard drive with the expectation of installing windows 7 on it and then working from there. The hard drive is recognized in the BIOS, the CMOS, and anything at all I've checked, but when I put the windows 7 64 bit disk in and try to do a custom install, seeing as I have nothing on the disk from which to upgrade, my hard drive does not show up in the section in which 7 asks where I want to install.

Motherboard is GIGABYTE GA-X58A-UD3R LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard, hard drive is Western Digital Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive.

The hard drive is plugged into the top SATA port (It has like, 10).

What can I do?

View 27 Replies


ADVERTISEMENT

Windows 7 Installation Doesn't Recognize Hard Drive

Oct 1, 2010

My mother asked me to fix her computer, his window XP is badly corrupted, so I tried to install Window 7 on her computer. However, the hard drive didn't show on the screen. I found it quite odd because BIOS detected it as IDE driver, and it's a SATA driver. I tried to install with old Window XP installation CD. Same thing, doesn't show on the window XP installation screen either.

I tried to hook hard drive on other computer, and was testing with Window 7 XD and see if it was working, and it did. It shown on the disk screen. My guess that it's probably the BIOS that occurred, or perhaps other things. I have one hard drive, nothing more.

View 9 Replies View Related

Windows 7 Doesn't Recognize The Information On 2nd Hard Drive

Aug 14, 2012

I have my WD75 Caviar Black 750G from my old computer it has all my files on it and it will not let me plug it in and look through it probably because the original computer was Win XP. Is there anyway to get the information off of the harddrive?

View 2 Replies View Related

Windows Explorer Doesn't Recognize Added Hard Drive

Aug 1, 2012

I recently attempted to add a hard drive to my Lenovo W520 laptop using a CD/DVD caddy accessory designed to hold a SATA hard drive.Windows recognized the new device and according to its messages, automatically installed the required device drivers. However, when I go into Windows Explorer, the new drive is nowhere to be found.Now, I know (or at least assume) this new drive probably needs to be formatted, but shouldn't it show up within Windows Explorer even in a pre-formatted state?

View 4 Replies View Related

Bad Sector On System 32 / Restarted Doesn't Recognize Hard Drive

Jun 11, 2011

I`ve got a serious problem with my vaio. i was surfing the net that i faced a BAD SECTOR ERROR on system 32. As I closed the ERROR,the system restarted. When I select the windows 7 to boot, the windows logo page come and restart again and again.Even when i decided to install a new version or repair it,the installation found no drive to install on.\

View 1 Replies View Related

Laptop Acer Aspire Doesn't Recognize External Hard Drive In Windows 7

Mar 28, 2011

my laptop acer aspire doesnt recognize my external hard drive in windows7. I will be great ful to them. it doesn't show any external hard drive but it shows pen drive and mobile usb cable but not external hard disk

View 1 Replies View Related

Win7 Doesn't Recognize All Of My Ram

Oct 27, 2009

i just installed win7 64-bit. i have a core i5 with 8GB RAM. the computer doesn't seem to recognize all 8GB. it says there is only 4GB installed. i thought that win7 could go way beyond the 4GB limit of vista. does anyone have any suggestions on how i can get my pc to recognize and utilize all my RAM?

another thing i noticed, is that win7 seems to run my GPU (Nvidia gtx 260) hotter. its running at idle with limited apps at ~38 C compared to vista which ran at 33-35 C. anyone know why win7 runs "hotter" than vista? i thought it was supposed to be more efficient?

View 13 Replies View Related

Install Sata Hard Drive As A Slave Where The Master Is Also A Sata?

Aug 10, 2011

i want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7

View 4 Replies View Related

Install Win7 On SATA Drive

Sep 29, 2009

I have a HP m7667c, which has two SATA drives. The motherboard is ASUS P5BW-LA (or Basswood-UL8E). I've never successfully installed vista before because of it kept asking for SATA drive. I wonder if there is a solution for this problem with Window 7?

I think I have RAID on in the BIOS configuration but I don't really want to turn it off because in that way my old WinXP would die. I just wanted to give Windows 7 a try before I completely change to it. Could anyone help me? I could provide more information about the desktop if necessary.

View 0 Replies View Related

Partitioning A Single Sata Drive With Win7 On It

May 28, 2009

I got a question for you maybe you can answer for me. I have a single 1terabyte sata drive with windows 7 on it. I used to have Windows xp pro on it but i upload Windows 7, i just delete the "old windows" that Windows 7 left me. Now i have accumulated alot of files in my documents file which i use for video purposes which take up about 530 gigs.

i can't wipe my hard drive clean to install the new update rc which i recieved as a beta tester. Is there any way to partition the drive only where Windows 7 is at leaving my 530 gigs in a seperate partition so that i can install dual os's. The two os's will be Windows 7 rc and Xp Pro. the only reason i made the switch is because i built my new computer with 4 gigs of memory running core 7 processor but xp only sees 3 gigs.

View 8 Replies View Related

Dual Boot - XP On First Drive (SATA) Win7 Second (IDE)

Dec 5, 2009

I am running XP on a SATA HDD. I have installed Win 7 on a second partition with some problems. The main problem was random BSOD's. This I believe, I have traced back to the fact that the MoBo runs Nvidia chips. Have downloaded the updated Nvidia Win 7 chip drivers. So, I uninstalled Win 7 and removed boot loader via BCDEDIT.

What I would now like to try is to install Win 7 on a separate IDE HDD connected to the primary IDE controller. This is so I can sort out the Nvidia driver problem.

I can see problems with this. My questions are the following:
What will I set the IDE HDD to be, Master or Slave? Then boot off DVD/ROM and then install Win 7 as normal onto IDE HDD. If yes, I take it that the Windows 7 bootloader will not be installed on the XP SATA HDD. If this is the case then I should be able to use EasyBCD to add the XP on the SATA HDD. Most critical part of the whole deal will be to set the SATA HDD (with XP) to boot FIRST. I have been down this track before and the MoBo sets the IDE as Drive 0 (FIRST boot HDD).

I know that there is a simple answer to this. I just cannot see the forest for the trees at present.

View 5 Replies View Related

Transfer Files From Bad Sata Hard Drive To New Hard Drive?

Dec 24, 2011

I have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?

View 4 Replies View Related

DVD RW Drive Doesn't Recognize Some CDs And DVDs?

Nov 29, 2012

Most of CDs and DVDs are working fine, but there are some which my DVD RW doesn't recognize. When I insert them, it doesn't react at all or it says that CD/DVD is blank. These CDs and DVDs are working without any problems on my old computer with Windows XP and also on my brother's laptop with Windows XP.

View 4 Replies View Related

Windows 7 Doesn't Recognize Usb 2.0 To Ide Cd/dvd/rw Drive?

Oct 5, 2011

have an acer veriton, trying to hook up an external cd/dvd drive.

View 4 Replies View Related

Add A 3rd SATA Hard Drive?

Jan 19, 2012

I am wanting to add a 3rd drive to my dell GX620. It has only 2 ports for SATA. Any good ideas on how to do this? Maybe convert an EIDE port?

I have a sata dvd writer, and two sata hard drives. Hoping to use them all. DVD writer is a lightscribe that's why I wanted to keep it.

View 3 Replies View Related

Hard Drive IDE SATA

Nov 27, 2009

My setup: XP on my C-drive with 2x SATA drives as slaves.

My requirement: I want to take my drives out and just use one of my SATA drives to install WINDOWS 7. If i tell my BIOS that my new C-Drive is that SATA drive, will i have to tell it again that my old drive is an IDE when i put that back in without the new SATA drive plugged in.

My reason: I have got the new WINDOWS 7 and want to install everything and update all my programs also have a good look and learn before i start having my work on it. It is easier for me to just unplug the power leads on each drive before i start then to have to redo all my work if i mess WINDOWS 7 up and have to format. I cant afford to loose everything.

Yes i could back everything up but i need to work while this is happening if you know what i mean.

View 5 Replies View Related

Install Windows 7 With Sata Hard Drive And IDE DVD ROM Drive

Oct 8, 2010

I have tried numerous times on my PC to install Windows 7 onto my Sata Drive to no avail. Yet as soon as I plug in my IDE HD it installs fine.I have unplugged all external peripherals USB and internal Card Reader. Set my Bios ok as it sees both the Hard Drive and DVD fine (Both in the bios and during selection of hard drive during windows 7 installation). Yet when I come to install it, it craps out at a random percentage saying cannot read from source or worse yet it crawls so slow through the percentages (I really don't think Windows 7 should take 6 hours to get to 15%!!) Yet both the hard drive and dvd are fine and the disc works great on my other PC without the sata drive in.

My motherboard is a Biostar G31-M7 TE with latest bios now what is odd is that I recently updated the BIOS to the latest one so does my problem come from here or was it always going to be a problem on this board? Also when I do have Windows 7 installed on the IDE drive when I plug in ther sata drive inside the whole system goes belly up (from freezes when transferring large files to just not seeing the drive)

View 9 Replies View Related

SATA Hard Drive Not Detected

Nov 26, 2010

I am trying to install windows 7 for a friend but the hard drive isn't detected within windows setup or within the bios. I have tried installing SATA drivers to try and get windows to recognise the hard drive but to no avail. Is there anything else I can try before assuming that the hard drive may be faulty?

View 2 Replies View Related

SATA Hard Drive Connections

Oct 11, 2012

My SATA hard drive has three connectors, power, SATA and to the right is an additional male four pin connector. What connects to that connector?

View 16 Replies View Related

Cannot Recognize Hard Drive

Aug 20, 2011

Today I did a clean install of Windows 7 on a 64 GB SSD. While it was installing my 1 TB secondary drive was not connected.

After everything was finished I connected the Second Drive. It can be seen in devices, but I am not allowed to access it. I have checked disk managment under Adminstrative tools and it is also not there.

View 3 Replies View Related

SSD Hard Drive - Use SATA As IDE Or AHCI In BIOS

Sep 28, 2012

I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.

But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.

I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.

View 4 Replies View Related

Windows 7 Won't Boot With Second SATA Hard Drive?

Jun 28, 2011

I've recently purchased two 30GB SSDs which I have set up in a RAID 0 array and I have installed Windows onto these drives. I have a second, 2TB Seagate Barracuda Green HDD that I have used to put my user profiles and additional programs/games on as it wouldn't fit on the SSD.Everything was fine for a few days after installation. Then this morning I rebooted the computer and it just stalled on the flashing cursor (underscore) in the top left corner of the screen. I did the basic fixes (Windows repair, checking RAM) and nothing worked.Then I thought that I should try disconnecting all but the SSD with the OS on it. SUCCESS! It booted to Windows but couldn't find any programs/user data so it created a new "profile". I shutdown the computer and tried reconnecting just the data hard drive.I have two additional hard drives (used for backups) that don't affect anything at all when I plug them in.Does anybody know what could be the problem? I'm at a loss and I need the computer

View 3 Replies View Related

Win 7 Unable To Detect SATA Hard Drive

Dec 20, 2009

I recently embarked on the journey of building my first custom PC. Everything was going well, until I hit a speed bump of installing Windows 7 64 bit. So like usual I boot from the CD drive, and stick Windows 7 in. When it gets to the point where I'm going to install, it is unable to find my SATA drive to install Windows 7 on.

It then asks me to "locate drivers." So it gives me an option to browse, and when it does so I put in the disk that came with my mobo, but it's unable to find any drivers. I tried downloading drivers from my motherboard's web site, sticking them on an external HD, and locating them from there, but that still didn't work.

I checked in my BIOS, and my SATA type is under Native IDE. I tried switching it to AHCI, and my HD was no longer detected in the BIOS, switched back to Native IDE and it found it again. Also, Onchip IDE Channel is set to Disabled, and Onchip SATA Control is set to Enabled, does this matter any?

I was wondering,though, is it possible that if I set the SATA type to AHCI, move the SATA cables into ports so that the drive is recognized by my BIOS, use the AHCI drivers I downloaded, Windows 7 will detect it?

View 5 Replies View Related

SATA Hard Drive - How To Install And Setup

Mar 1, 2010

How to Install and Setup a SATA Hard Drive ?

View 0 Replies View Related

Can A 2tb Sata Hard Drive Be Installed On Optiplex 745

Jun 1, 2012

No success getting windows 7 to install with 2 TB sata hard drive. It reads on BIOS but when installer setup for W7 it stops in the beginning with "required cd/dvd driver missing"; asking you to go ahead and remove your installer disk for that particular step only.

View 1 Replies View Related

Windows 7 Won't Recognize The Hard Drive

Mar 5, 2011

I am building a computer fort the first time and I am having trouble getting Windows 7 to recognize my hard drive. My har drive and mother board are as follows: Hard drive-Seagate Barracuda 7200.12 ST3500418AS 500GB 7200 RPM 16MB Cache SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive, Mother Board-GIGABYTE GA-870A-UD3 AM3 AMD 870 SATA 6Gb/s USB 3.0 ATX AMD Motherboard when I go to install windows 7 I eventually get to a screen where it ask for an install location, unfortunately it doesn�t seem to recognize my hard drive. It gives me an option of installing driver so I went to the gigabyte website and downloaded the drivers that it said I required. I believe there was an ACHI driver and a Raid driver. After I stalled both of these drivers the hard drive still was not detected. One strange thing I noticed was that when I browse for a driver my hard drive is listed as a place I can search. I then proceeded to the Bios to try and match the drivers. The hard drive is detected in the Bio. When the HD is set to IDE my BluRay play is able to read the windows install disc. But windows won�t recognize my HD. If I set it to ACHI or Raid I can�t seem to get the windows CD to load. Do I need an IDE driver? Out of frustration I tried installing a windows XP to see if it would be able to recognize my hard drive. It seemed to load on the hard drive fine but entered this weird loop where windows would install itself but wouldn�t actually load as the operating system. In other words when I try to restart my computer and run the OS off of my hard drive it gave me an error message. Something like (windows OS could not be located) When I went to go install windows 7 again my hard drive still was not detected as a place to intall windows but when I search the hard drive (as if I was searching for a driver) I can see the Windows files that were loaded from when I tried to install XP.

View 5 Replies View Related

Windows 7 Won't Recognize IDE Hard Drive & DVD Drive

Apr 1, 2012

I recently installed windows 7 home premium 64 bit, previous OS was Vista home premium 32 bit. My desktop is an HP pavilion d4650y. I have the OS loaded on my main HD which is a SATA.

HD & DVD drive worked perfectly before on vista. I tested both devices on another pc with XP and they work fine. I've triple checked the connections but still the devices are not recognized by Windows 7. I've also tried renaming the HD & changing the drive letter, but still no luck.

Both drives are connected to a PCI E card, and are set to cable select, on separate cables. In the BIOS both drives show up. In disk management they do not show up at all.

My HD is a western digital 250 gb EIDE, and the DVD drive is a IDE Pioneer DVD burner (secondary disc drive).

View 5 Replies View Related

2TB Hard Drive Won't Work On Marvell 6GB SATA Port

Jun 8, 2011

Intel Core i7-960 3.20GHz LGA1366 CPU BX80601960
MB Intel BOX DX58OG
PSU Corsair 600W
MEM 4G KST KVR1333D3/4GR x3
EVGA GeForce GTX 560 Ti
Western Digital 500 GB SATA 6.0 GB-s Internal OEM Drive WD5000AAKX
Western Digital 2 TB Caviar Black SATA 6GB/s Internal OEM Drive WD2002FAEX

Just built this machine. Installed Windows 7 on the 500GB drive. Both drives are plugged into the blue SATA 6GB ports on my board. My drivers for these controllers are Marvell 91xx SATA 6G v1.2.0.1002 (Dated 3/7/2011). The second 2TB drive shows up in BIOS as well as Drive Management in Windows, but it will not be recognized as an accessible drive that can be formatted, partitioned, or anything. I get an error each time I attempt to format or partition through Drive Management. When I plug the 2TB drive into one of the other (black, Intel) SATA ports, the drive works fine, but in the blue ports it just won't seem to work. The 500GB drive, however, works perfectly as the boot disk in these ports.

View 9 Replies View Related

SATA USB Adapter With Macbook Formatted Hard Drive?

Apr 28, 2012

I am trying to access my wife's macbook hard drive via my Windows computer using the Vantec SATA/IDE to USB 2.0 Adapter. The Apple techs said they could not get the drive to register when they hooked it up. However, we gave it a good drying with blow dryerThe adapter works fine and all the correct drivers installedI am in disk management and the 250GB drive seems to be showing up. However, it is not showing up in My Computer and right click shows "assign a letter" is grayed out.

View 2 Replies View Related

Open Sata Slave And Master Hard Drive?

Sep 20, 2012

find a solution to how open sata slave and master hard drive on a desktop

View 1 Replies View Related

Computer Won't Recognize External Hard Drive?

Jul 22, 2011

I'm having some trouble getting an external hard drive to be recognized by my computer. I have quite a few already, but I got another one because one of them won't read on my comp, although it will read on my netbook. The new drive I got has the same issue, no go on the comp, but works fine on the netbook.

I tried unplugging all of the other drives and even using the other cables to connect the new drive, but Windows 7 simply won't recognize it being plugged in. No "badump" sound and no icon in My Computer. Tried restarting, nothing. I tried it in all six of my computer's USB ports, but got no better result.

View 10 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved