2TB Hard Drive Won't Work On Marvell 6GB SATA Port
Jun 8, 2011
Intel Core i7-960 3.20GHz LGA1366 CPU BX80601960
MB Intel BOX DX58OG
PSU Corsair 600W
MEM 4G KST KVR1333D3/4GR x3
EVGA GeForce GTX 560 Ti
Western Digital 500 GB SATA 6.0 GB-s Internal OEM Drive WD5000AAKX
Western Digital 2 TB Caviar Black SATA 6GB/s Internal OEM Drive WD2002FAEX
Just built this machine. Installed Windows 7 on the 500GB drive. Both drives are plugged into the blue SATA 6GB ports on my board. My drivers for these controllers are Marvell 91xx SATA 6G v1.2.0.1002 (Dated 3/7/2011). The second 2TB drive shows up in BIOS as well as Drive Management in Windows, but it will not be recognized as an accessible drive that can be formatted, partitioned, or anything. I get an error each time I attempt to format or partition through Drive Management. When I plug the 2TB drive into one of the other (black, Intel) SATA ports, the drive works fine, but in the blue ports it just won't seem to work. The 500GB drive, however, works perfectly as the boot disk in these ports.
I bought a cable with ESATA on one end and SATA on the other end. What am I supposed to do with it? I connected a standard SATA drive to one end and the other end to the ESATA port on the back of the computer, and used an external power supply for the drive. The BIOS does not see the drive. Suspecting the drive needed to be powered from the same power supply as the computer, I plugged the drive into a normal power connector in the computer, but used the new cable to connect it to the external ESATA port. Still the BIOS sees nothing. The drive works perfectly as a SATA drive in the normal SATA connection.
Intel D975XBX2 Marvell SATA driver needed for Windows 7
Installed Windows 7 (62 bit) onto Intel D975XBX2 ATX Motherboard.
I can not get windows to recognize the SATA drives attached to the internal Marvell card.
BIOS see the drives, just not windows.
Attempted to install both Windows XP 64 and Vista 64 Intel drivers (STOR_allOS_8.7.0.1007_PV), but the install fails with "system does not meet the minimum requirements)
I have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?
My setup: XP on my C-drive with 2x SATA drives as slaves.
My requirement: I want to take my drives out and just use one of my SATA drives to install WINDOWS 7. If i tell my BIOS that my new C-Drive is that SATA drive, will i have to tell it again that my old drive is an IDE when i put that back in without the new SATA drive plugged in.
My reason: I have got the new WINDOWS 7 and want to install everything and update all my programs also have a good look and learn before i start having my work on it. It is easier for me to just unplug the power leads on each drive before i start then to have to redo all my work if i mess WINDOWS 7 up and have to format. I cant afford to loose everything.
Yes i could back everything up but i need to work while this is happening if you know what i mean.
I have tried numerous times on my PC to install Windows 7 onto my Sata Drive to no avail. Yet as soon as I plug in my IDE HD it installs fine.I have unplugged all external peripherals USB and internal Card Reader. Set my Bios ok as it sees both the Hard Drive and DVD fine (Both in the bios and during selection of hard drive during windows 7 installation). Yet when I come to install it, it craps out at a random percentage saying cannot read from source or worse yet it crawls so slow through the percentages (I really don't think Windows 7 should take 6 hours to get to 15%!!) Yet both the hard drive and dvd are fine and the disc works great on my other PC without the sata drive in.
My motherboard is a Biostar G31-M7 TE with latest bios now what is odd is that I recently updated the BIOS to the latest one so does my problem come from here or was it always going to be a problem on this board? Also when I do have Windows 7 installed on the IDE drive when I plug in ther sata drive inside the whole system goes belly up (from freezes when transferring large files to just not seeing the drive)
I am trying to install windows 7 for a friend but the hard drive isn't detected within windows setup or within the bios. I have tried installing SATA drivers to try and get windows to recognise the hard drive but to no avail. Is there anything else I can try before assuming that the hard drive may be faulty?
I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.
But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.
I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.
I've recently purchased two 30GB SSDs which I have set up in a RAID 0 array and I have installed Windows onto these drives. I have a second, 2TB Seagate Barracuda Green HDD that I have used to put my user profiles and additional programs/games on as it wouldn't fit on the SSD.Everything was fine for a few days after installation. Then this morning I rebooted the computer and it just stalled on the flashing cursor (underscore) in the top left corner of the screen. I did the basic fixes (Windows repair, checking RAM) and nothing worked.Then I thought that I should try disconnecting all but the SSD with the OS on it. SUCCESS! It booted to Windows but couldn't find any programs/user data so it created a new "profile". I shutdown the computer and tried reconnecting just the data hard drive.I have two additional hard drives (used for backups) that don't affect anything at all when I plug them in.Does anybody know what could be the problem? I'm at a loss and I need the computer
I recently embarked on the journey of building my first custom PC. Everything was going well, until I hit a speed bump of installing Windows 7 64 bit. So like usual I boot from the CD drive, and stick Windows 7 in. When it gets to the point where I'm going to install, it is unable to find my SATA drive to install Windows 7 on.
It then asks me to "locate drivers." So it gives me an option to browse, and when it does so I put in the disk that came with my mobo, but it's unable to find any drivers. I tried downloading drivers from my motherboard's web site, sticking them on an external HD, and locating them from there, but that still didn't work.
I checked in my BIOS, and my SATA type is under Native IDE. I tried switching it to AHCI, and my HD was no longer detected in the BIOS, switched back to Native IDE and it found it again. Also, Onchip IDE Channel is set to Disabled, and Onchip SATA Control is set to Enabled, does this matter any?
I was wondering,though, is it possible that if I set the SATA type to AHCI, move the SATA cables into ports so that the drive is recognized by my BIOS, use the AHCI drivers I downloaded, Windows 7 will detect it?
No success getting windows 7 to install with 2 TB sata hard drive. It reads on BIOS but when installer setup for W7 it stops in the beginning with "required cd/dvd driver missing"; asking you to go ahead and remove your installer disk for that particular step only.
I have a Router with ethernet and usb ports on it, and want to use the usb port to plug an external hard drive into it. Is this possible or is the usb port only for connecting to a PC.
I am trying to access my wife's macbook hard drive via my Windows computer using the Vantec SATA/IDE to USB 2.0 Adapter. The Apple techs said they could not get the drive to register when they hooked it up. However, we gave it a good drying with blow dryerThe adapter works fine and all the correct drivers installedI am in disk management and the 250GB drive seems to be showing up. However, it is not showing up in My Computer and right click shows "assign a letter" is grayed out.
I built a new computer. Rather expensive, but it should perform well. -Anyway-, I bought a brand new hard drive with the expectation of installing windows 7 on it and then working from there. The hard drive is recognized in the BIOS, the CMOS, and anything at all I've checked, but when I put the windows 7 64 bit disk in and try to do a custom install, seeing as I have nothing on the disk from which to upgrade, my hard drive does not show up in the section in which 7 asks where I want to install.
Motherboard is GIGABYTE GA-X58A-UD3R LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard, hard drive is Western Digital Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive.
The hard drive is plugged into the top SATA port (It has like, 10).
My D 200gb SATA hard drive disappears around 1-90 mins while on windows 7. I have tried registry repairs and alot of things. Its not faulty cables because i used to have win Xp on exact same computer but reformatted to windows 7. Rebooting makes the hard drive reappear but it still disappears after a while. It still shows up in the bios though. When it disappears, it is completely gone, even in device manager.
my important data is on my 200gb D drive and i only use C for my os and some other things like Firefox because its only 80gb
Interaction (interface?) between a Sabrent USB 2.0 to SATA/IDE Hard Drive Adapter Product Code: USB-DSC5 and my Windows 7 Home Premium 64-bit?When connected to IDE Drives Maxtor and Western Digital, and through the usage of Windows 7 it tellls me that the Hard Drive "is not ready". Is that a message originated by the Windows 7 software?If so how do I go about "getting the disk ready" so i could change disk type or number or sizes of each partition and/or reformat?unexpected report from the Windows 7 interaction with this adapter and the Hard Drives it holds, 40 GB and 80 GB IDE drives Maxtor and Western Digital. I am trying to use Windows (or some other third party software) to resize the partitions, change the disk type and eventually reformat.
i am trying to connect my internal harddrive for my dead laptop via a usb port of a working one, but i get the message that the device is not recognized
I have a Dell Inspiron 1545 laptop. I recently developed hard drive trouble and have had to order a replacement.Instead of installing Windows 7 all over again, with all the drivers, etc., I want to clone my existing hard drive to the new one.I intend to connect one of the hard drives to my system via a USB SATA cable with the other drive connected inside my system.
I formatted and installed windows 7 64 bit in a pc which previously had windows 7 32 bit. When i booted my 1tb dynamic disk was not detected. So I went into disk management and it had listed my disk as "Foreign Disk". So i imported the foreign disk.
The drive was detected and opened. So i rebooted the pc but now the drive is still not appearing in my computer. When i go to disk management the 1tb appears but there is no drive letter assigned. When i try to assign drive letter it statest that "Specified File cannot be found"
i installed a sata controller because the sata controller on the motherboard went out. I can easily install ubuntu but when i try installing win 7 it asks for a cdrom driver, when i try booting from usb it asks for hdd driver.
As you probably know the issue is that the HDD shows as removable device in the taskbar.
I have the lastest drivers available from Asmedia and it does not remove the icon from the taskbar.
I also try the MS register fix My internal SATA device appears in Devices and Printers and in the - Microsoft Answers
1- Since the sata port is not Intel , would the register location be the same for the proposed solution above to work?
2- I tried channels 0..5 , should I try any other number? The solution says that the channel in device manager it is not always the correct one. Under device manager , general tab it displays "Location 0 (Channel 1, Target 0, Lun 0)"
I am building a htpc but cannot seem to get windows to install onto my SSD.The SSD is visible in BIOS and on the 'where do you want to install windows' screen.I am wondering if that is because the OS cannot install to my mobos sata 3 portsI havecrucial m4 SSD 4GBMSI H61MA-E35 with usb3/sata3The sata 3 ports are ASmedia according to the manual.i think i know where this is heading and will be fairly annoyed if so because i bought this board specifically for the sata 3 boot drive option.
