SSD Hard Drive - Use SATA As IDE Or AHCI In BIOS

Sep 28, 2012

I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.

But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.

I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.

View 4 Replies


ADVERTISEMENT

Switching BIOS SATA RAID/AHCI Setting Causes BSOD At Windows Start

Mar 30, 2012

I just changed my disk setup from:

1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1

TO:

1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]

Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.


These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.

What am I missing? Why can't I set it to AHCI mode without BSODs?

View 8 Replies View Related

Intel Sata Controler ICH10R AHCI + Jmicron AHCI Error

Jul 16, 2009

I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.

As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.

View 3 Replies View Related

Changed The SATA Controller From AHCI To Raid SATA Result = FAILED?

Aug 10, 2010

Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:

At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED

On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.

View 9 Replies View Related

Install Sata Hard Drive As A Slave Where The Master Is Also A Sata?

Aug 10, 2011

i want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7

View 4 Replies View Related

Flashing Bios On An Adaptec 1220 SATA Drive Controller

May 26, 2009

I'm going to install RC1 in the next few days.

I was looking to test the stability within RC1 of an adaptec 1220SA card I have to control the system drives. I have the Vista 64bit driver for the card as this is the newest listed.

I have created a recovery disc in beta build 7000 and hope to use this to boot into a DOS shell and follow the instructions given on the adaptec site:

This is the BIOS release v6.0-0 Build 2330 for the Adaptec SATA II RAID 1220SA Controller.

This BIOS should only be used together with Driver v1.6.12086 in Windows Server 2008 or Windows Vista.

This self-extracting archive includes the flash utility, the BIOS image file and the Release Notes.

Caution: If the BIOS update fails with an error message "unable to find file" or "target controller does not match", please see ASK Answer ID 15241

Installation Instruction: This file is self extracting and will unzip to the directory adaptec1220sa. Copy the expanded files to a floppy diskette. The expanded files can also be copied to a USB device or CD-R.

Shut down the operating system and reboot to DOS from a bootable floppy disk, USB device or CD-R. Insert the media with the update files. Run the flash utility program named AFU.EXE included in this download to backup the current BIOS and flash the new BIOS image.

I'm hoping to expand the bios update file onto a cd for the second drive or alternatively stick it on a USB stick.

My question is this, when I am in the dos shell, what do I do!

I suddenly realised that i've never had a need to use the command line

View 5 Replies View Related

Transfer Files From Bad Sata Hard Drive To New Hard Drive?

Dec 24, 2011

I have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?

View 4 Replies View Related

AHCI Mode Stopped Reconizing Hard Drive

Oct 3, 2012

If the BIOS setting for the hard drive controller is AHCI it will not recognize the drive. (This was the default setting in the BIOS), If changed to IDE mode it recognizes the drive but come up with an "No operating system detected" message. If the hard drive is installed in a second lap top it works fine. If another hard drive is installed it works fine in AHCI mode. Only the combination of the original hard drive and the original lap top wont work.

View 9 Replies View Related

Configure SATA As IDE Or AHCI

Jun 7, 2009

In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.

If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.

Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.

View 4 Replies View Related

Add A 3rd SATA Hard Drive?

Jan 19, 2012

I am wanting to add a 3rd drive to my dell GX620. It has only 2 ports for SATA. Any good ideas on how to do this? Maybe convert an EIDE port?

I have a sata dvd writer, and two sata hard drives. Hoping to use them all. DVD writer is a lightscribe that's why I wanted to keep it.

View 3 Replies View Related

Hard Drive IDE SATA

Nov 27, 2009

My setup: XP on my C-drive with 2x SATA drives as slaves.

My requirement: I want to take my drives out and just use one of my SATA drives to install WINDOWS 7. If i tell my BIOS that my new C-Drive is that SATA drive, will i have to tell it again that my old drive is an IDE when i put that back in without the new SATA drive plugged in.

My reason: I have got the new WINDOWS 7 and want to install everything and update all my programs also have a good look and learn before i start having my work on it. It is easier for me to just unplug the power leads on each drive before i start then to have to redo all my work if i mess WINDOWS 7 up and have to format. I cant afford to loose everything.

Yes i could back everything up but i need to work while this is happening if you know what i mean.

View 5 Replies View Related

Install Windows 7 With Sata Hard Drive And IDE DVD ROM Drive

Oct 8, 2010

I have tried numerous times on my PC to install Windows 7 onto my Sata Drive to no avail. Yet as soon as I plug in my IDE HD it installs fine.I have unplugged all external peripherals USB and internal Card Reader. Set my Bios ok as it sees both the Hard Drive and DVD fine (Both in the bios and during selection of hard drive during windows 7 installation). Yet when I come to install it, it craps out at a random percentage saying cannot read from source or worse yet it crawls so slow through the percentages (I really don't think Windows 7 should take 6 hours to get to 15%!!) Yet both the hard drive and dvd are fine and the disc works great on my other PC without the sata drive in.

My motherboard is a Biostar G31-M7 TE with latest bios now what is odd is that I recently updated the BIOS to the latest one so does my problem come from here or was it always going to be a problem on this board? Also when I do have Windows 7 installed on the IDE drive when I plug in ther sata drive inside the whole system goes belly up (from freezes when transferring large files to just not seeing the drive)

View 9 Replies View Related

IDE Or AHCI For SATA Drives (SSD And Regular)

Sep 15, 2009

I would like the good and bad about running your SATA drives in IDE and AHCI modes.

I have 3 drives. 1 SSD and 2 normal hard drives.

Does it even make a difference? I have an Esata bracket that I want to run in AHCI mode but how about the normal system and data drives? What is the best way to set up drives?

View 0 Replies View Related

SATA Hard Drive Not Detected

Nov 26, 2010

I am trying to install windows 7 for a friend but the hard drive isn't detected within windows setup or within the bios. I have tried installing SATA drivers to try and get windows to recognise the hard drive but to no avail. Is there anything else I can try before assuming that the hard drive may be faulty?

View 2 Replies View Related

SATA Hard Drive Connections

Oct 11, 2012

My SATA hard drive has three connectors, power, SATA and to the right is an additional male four pin connector. What connects to that connector?

View 16 Replies View Related

Coming From XP, Enable AHCI For SATA Drives?

May 11, 2011

I'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.

My questions are:

1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?

2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)

3. I intend to run XP mode, will AHCI mode pose any problems for this?

View 2 Replies View Related

SATA AHCI Controller, IDE DVD RW Slow Speed

Aug 27, 2012

I have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.

My question:

SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s.
TDK DVD+R disks tested OK (on other PC) for 16X capability.
Why is Nero reporting of only 2.4X and 4X writting speeds?

View 7 Replies View Related

Changing SATA From Compatibility Mode To AHCI?

Oct 18, 2011

I'm installing Seven on a WinXP machine and completed the install, but forgot to change the SATA setting in the bios from "compatibility mode" to AHCI. Now when I change it, windows gives me bluescreen on boot.I'm dumbfounded that Windows Seven startup repair can't fix a problem this simple, but it completely failed, wasn't even able to find a problem.I was thinking it might be easier to just reformat and begin the install over again, or startup in safemode and install the intel SATA drivers... assuming it will let me boot into safemode with AHCI enabled.ps. On the other computer (different thread), I'm going to wait till I have several hours of uninterrupted time, in case I need to begin over installing all the windows versions one at a time. I'll reply with any success/failure on that thread later in the week.

View 4 Replies View Related

Sata Controller From Ahci To Compatible Mode?

Jul 13, 2012

I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.

View 1 Replies View Related

Windows 7 Won't Boot With Second SATA Hard Drive?

Jun 28, 2011

I've recently purchased two 30GB SSDs which I have set up in a RAID 0 array and I have installed Windows onto these drives. I have a second, 2TB Seagate Barracuda Green HDD that I have used to put my user profiles and additional programs/games on as it wouldn't fit on the SSD.Everything was fine for a few days after installation. Then this morning I rebooted the computer and it just stalled on the flashing cursor (underscore) in the top left corner of the screen. I did the basic fixes (Windows repair, checking RAM) and nothing worked.Then I thought that I should try disconnecting all but the SSD with the OS on it. SUCCESS! It booted to Windows but couldn't find any programs/user data so it created a new "profile". I shutdown the computer and tried reconnecting just the data hard drive.I have two additional hard drives (used for backups) that don't affect anything at all when I plug them in.Does anybody know what could be the problem? I'm at a loss and I need the computer

View 3 Replies View Related

Win 7 Unable To Detect SATA Hard Drive

Dec 20, 2009

I recently embarked on the journey of building my first custom PC. Everything was going well, until I hit a speed bump of installing Windows 7 64 bit. So like usual I boot from the CD drive, and stick Windows 7 in. When it gets to the point where I'm going to install, it is unable to find my SATA drive to install Windows 7 on.

It then asks me to "locate drivers." So it gives me an option to browse, and when it does so I put in the disk that came with my mobo, but it's unable to find any drivers. I tried downloading drivers from my motherboard's web site, sticking them on an external HD, and locating them from there, but that still didn't work.

I checked in my BIOS, and my SATA type is under Native IDE. I tried switching it to AHCI, and my HD was no longer detected in the BIOS, switched back to Native IDE and it found it again. Also, Onchip IDE Channel is set to Disabled, and Onchip SATA Control is set to Enabled, does this matter any?

I was wondering,though, is it possible that if I set the SATA type to AHCI, move the SATA cables into ports so that the drive is recognized by my BIOS, use the AHCI drivers I downloaded, Windows 7 will detect it?

View 5 Replies View Related

SATA Hard Drive - How To Install And Setup

Mar 1, 2010

How to Install and Setup a SATA Hard Drive ?

View 0 Replies View Related

Can A 2tb Sata Hard Drive Be Installed On Optiplex 745

Jun 1, 2012

No success getting windows 7 to install with 2 TB sata hard drive. It reads on BIOS but when installer setup for W7 it stops in the beginning with "required cd/dvd driver missing"; asking you to go ahead and remove your installer disk for that particular step only.

View 1 Replies View Related

AHCI Mode No Boot From Sata Optical Drives?

Apr 30, 2011

A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.

View 9 Replies View Related

Reinstall Windows 7 Upgrade On New Sata III As C: With AHCI Support?

Dec 18, 2010

Reinstall w7 Upgrade on new Sata III as c: with AHCI support?

View 9 Replies View Related

2TB Hard Drive Won't Work On Marvell 6GB SATA Port

Jun 8, 2011

Intel Core i7-960 3.20GHz LGA1366 CPU BX80601960
MB Intel BOX DX58OG
PSU Corsair 600W
MEM 4G KST KVR1333D3/4GR x3
EVGA GeForce GTX 560 Ti
Western Digital 500 GB SATA 6.0 GB-s Internal OEM Drive WD5000AAKX
Western Digital 2 TB Caviar Black SATA 6GB/s Internal OEM Drive WD2002FAEX

Just built this machine. Installed Windows 7 on the 500GB drive. Both drives are plugged into the blue SATA 6GB ports on my board. My drivers for these controllers are Marvell 91xx SATA 6G v1.2.0.1002 (Dated 3/7/2011). The second 2TB drive shows up in BIOS as well as Drive Management in Windows, but it will not be recognized as an accessible drive that can be formatted, partitioned, or anything. I get an error each time I attempt to format or partition through Drive Management. When I plug the 2TB drive into one of the other (black, Intel) SATA ports, the drive works fine, but in the blue ports it just won't seem to work. The 500GB drive, however, works perfectly as the boot disk in these ports.

View 9 Replies View Related

SATA USB Adapter With Macbook Formatted Hard Drive?

Apr 28, 2012

I am trying to access my wife's macbook hard drive via my Windows computer using the Vantec SATA/IDE to USB 2.0 Adapter. The Apple techs said they could not get the drive to register when they hooked it up. However, we gave it a good drying with blow dryerThe adapter works fine and all the correct drivers installedI am in disk management and the 250GB drive seems to be showing up. However, it is not showing up in My Computer and right click shows "assign a letter" is grayed out.

View 2 Replies View Related

Win7 Doesn't Recognize SATA Hard Drive

Jan 30, 2010

I built a new computer. Rather expensive, but it should perform well. -Anyway-, I bought a brand new hard drive with the expectation of installing windows 7 on it and then working from there. The hard drive is recognized in the BIOS, the CMOS, and anything at all I've checked, but when I put the windows 7 64 bit disk in and try to do a custom install, seeing as I have nothing on the disk from which to upgrade, my hard drive does not show up in the section in which 7 asks where I want to install.

Motherboard is GIGABYTE GA-X58A-UD3R LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard, hard drive is Western Digital Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive.

The hard drive is plugged into the top SATA port (It has like, 10).

What can I do?

View 27 Replies View Related

Open Sata Slave And Master Hard Drive?

Sep 20, 2012

find a solution to how open sata slave and master hard drive on a desktop

View 1 Replies View Related

Oparating System Not Found When Booting Is Sata Option AHCI?

May 17, 2012

i have an m17 r2 alienwAre laptop.in the bios menu the sata option HCAI is selected but when the comp boots it says no operating system is found when booting for bios sata option RAID it runs fine. But the comp should be on HCAI in order to run features that a specific to that computer . I have tryed reformatting but in HCAI it on finds the second of 2 500g hard drives but the partition with the boot is on hdd1 not hdd2 . Boot up again with RAID it finds both and and I can reformat have tryed to reset the registry and have tryed using drivermax to find out if I'm missing sata drivers I've also tryed reinstalling my bios from the dell

View 6 Replies View Related

How To Set SSD And HDD In The Bios (AHCI, IDE)

Aug 8, 2012

I have SSD as primary system drive and 2x512GB HDDs as RAID 1 for storage.In bios i have options to set them as AHCI, IDE and one more that i forgot...

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved