Win 7 Unable To Detect SATA Hard Drive
Dec 20, 2009
I recently embarked on the journey of building my first custom PC. Everything was going well, until I hit a speed bump of installing Windows 7 64 bit. So like usual I boot from the CD drive, and stick Windows 7 in. When it gets to the point where I'm going to install, it is unable to find my SATA drive to install Windows 7 on.
It then asks me to "locate drivers." So it gives me an option to browse, and when it does so I put in the disk that came with my mobo, but it's unable to find any drivers. I tried downloading drivers from my motherboard's web site, sticking them on an external HD, and locating them from there, but that still didn't work.
I checked in my BIOS, and my SATA type is under Native IDE. I tried switching it to AHCI, and my HD was no longer detected in the BIOS, switched back to Native IDE and it found it again. Also, Onchip IDE Channel is set to Disabled, and Onchip SATA Control is set to Enabled, does this matter any?
I was wondering,though, is it possible that if I set the SATA type to AHCI, move the SATA cables into ports so that the drive is recognized by my BIOS, use the AHCI drivers I downloaded, Windows 7 will detect it?
View 5 Replies
ADVERTISEMENT
Dec 18, 2011
windows 7 pro 64 bit does not detect any hard drives - i have 4 sata - new install?
View 1 Replies
View Related
Mar 4, 2012
I have a Dell Inspiron 1545 laptop. I recently developed hard drive trouble and have had to order a replacement.Instead of installing Windows 7 all over again, with all the drivers, etc., I want to clone my existing hard drive to the new one.I intend to connect one of the hard drives to my system via a USB SATA cable with the other drive connected inside my system.
View 2 Replies
View Related
May 26, 2012
I formatted and installed windows 7 64 bit in a pc which previously had windows 7 32 bit. When i booted my 1tb dynamic disk was not detected. So I went into disk management and it had listed my disk as "Foreign Disk". So i imported the foreign disk.
The drive was detected and opened. So i rebooted the pc but now the drive is still not appearing in my computer. When i go to disk management the 1tb appears but there is no drive letter assigned. When i try to assign drive letter it statest that "Specified File cannot be found"
View 1 Replies
View Related
Aug 10, 2011
i want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7
View 4 Replies
View Related
Dec 24, 2011
I have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?
View 4 Replies
View Related
Jan 19, 2012
I am wanting to add a 3rd drive to my dell GX620. It has only 2 ports for SATA. Any good ideas on how to do this? Maybe convert an EIDE port?
I have a sata dvd writer, and two sata hard drives. Hoping to use them all. DVD writer is a lightscribe that's why I wanted to keep it.
View 3 Replies
View Related
Nov 27, 2009
My setup: XP on my C-drive with 2x SATA drives as slaves.
My requirement: I want to take my drives out and just use one of my SATA drives to install WINDOWS 7. If i tell my BIOS that my new C-Drive is that SATA drive, will i have to tell it again that my old drive is an IDE when i put that back in without the new SATA drive plugged in.
My reason: I have got the new WINDOWS 7 and want to install everything and update all my programs also have a good look and learn before i start having my work on it. It is easier for me to just unplug the power leads on each drive before i start then to have to redo all my work if i mess WINDOWS 7 up and have to format. I cant afford to loose everything.
Yes i could back everything up but i need to work while this is happening if you know what i mean.
View 5 Replies
View Related
Oct 8, 2010
I have tried numerous times on my PC to install Windows 7 onto my Sata Drive to no avail. Yet as soon as I plug in my IDE HD it installs fine.I have unplugged all external peripherals USB and internal Card Reader. Set my Bios ok as it sees both the Hard Drive and DVD fine (Both in the bios and during selection of hard drive during windows 7 installation). Yet when I come to install it, it craps out at a random percentage saying cannot read from source or worse yet it crawls so slow through the percentages (I really don't think Windows 7 should take 6 hours to get to 15%!!) Yet both the hard drive and dvd are fine and the disc works great on my other PC without the sata drive in.
My motherboard is a Biostar G31-M7 TE with latest bios now what is odd is that I recently updated the BIOS to the latest one so does my problem come from here or was it always going to be a problem on this board? Also when I do have Windows 7 installed on the IDE drive when I plug in ther sata drive inside the whole system goes belly up (from freezes when transferring large files to just not seeing the drive)
View 9 Replies
View Related
Dec 18, 2011
I have tried to use this IOMAX USB 2.0 to SATA/IDE Adapter Kit with Power: Amazon.co.uk: Electronics to connect an old 250 gb Samsung sata hard drive to my PC.Windows won't recognise it as a hard drive/partition - the USB adapter device is recognised, and via Devices & Printers, it shows the drive, but not as a USB External Drive, (see image) so I cannot access it.
View 3 Replies
View Related
Dec 30, 2011
On my old secondary computer my setup was
Motherboard: Chaintech VNF2-350
Master 0: HDS722516VLAT80 with Windows installation
Slave 0: WD800BB-53CCB0
But then I started getting Machine Check Exceptions and my motherboard ultimately perished. So I replaced that with a Foxconn K8S755A-6ELRS. But this new motherboard won't detect the hard drive.
It will hang at the part that says "Detecting IDE drives", sometimes it will give up and display "0" where the drive is supposed to be, other times it will hang until you unplug the cable.
If it's on the same channel as the Hitachi drive with XP on it, the BIOS recognizes the other drive, but fails to boot from it. If they are on different channels, it boots the XP drive but will see no hint of the drive on the other channel., even in Disk Management or Device Manager.
I also tried connecting it to my other computer's Intel DP35DP mobo, and it was able to detect/read/write and all that, though it does have a few bad sectors.
View 4 Replies
View Related
Jul 22, 2012
Recently I change my Os from windows vista to 7. Because I can't find a way to make the original OS to become genuine.From there, my laptop can't read external hard drive but it can only read flash drives.I don't know what my laptop is missing, if it is updates or drivers.
View 8 Replies
View Related
Nov 8, 2011
i was installing window 7 and so far i have ubuntu installed but the set up could not detect any hard drive
View 3 Replies
View Related
Nov 26, 2010
I am trying to install windows 7 for a friend but the hard drive isn't detected within windows setup or within the bios. I have tried installing SATA drivers to try and get windows to recognise the hard drive but to no avail. Is there anything else I can try before assuming that the hard drive may be faulty?
View 2 Replies
View Related
Oct 11, 2012
My SATA hard drive has three connectors, power, SATA and to the right is an additional male four pin connector. What connects to that connector?
View 16 Replies
View Related
Jan 12, 2012
I opened my external drive case and took the 3.5" hard drive out so that I could connect to the computer internally with a SATA cable because I don't have an external SATA cable and internal SATA interface. I started the Windows 7 Ultimate system. The computer screen remained on "Starting Windows" forever.If my memory serves me right, I remember I did manage to access it with another computer before. That computer has been out of service. At present I can access it while the drive is in the case connected with a USB cable. The Windows explorer shows all the partitions in the drive.
View 4 Replies
View Related
May 14, 2009
Install everything, the bios detect the hard drive (it's a new hard drive, never been use) but when installing the Windows 7 64, the hard drive list is empty.
Here my spec
Phenom II 940BE | Gigabyte 790X-UD4P | Seagate Barracuda 7200.12 500GB | XFX HD4770 512MB | OCZ StealthXStream 600W | NZXT Tempest
View 2 Replies
View Related
Feb 17, 2011
Here's my hard drive: Seagate Constellation ES ST3500514NS
I haven't been able to get Windows 7 installation to detect this drive for about two months now. I'm running on a Gigabyte GA-880GA-UD3H mobo, revision 2.1.
I recently found a list of drivers for my motherboard on Gigabyte. I also found some downloads for my hard drive.
Oh, and I can use this drive if I'm running Windows 7 on a different hard drive, but I just can't install Windows 7 on it.
View 5 Replies
View Related
Oct 17, 2012
When i connect Seagate 1 TB external harddisk to my computer ,initially the light is blinking up and then its stopped and note showingdetecting anywhere in computer(diskamanager too),is there anyway to make detect and recover my datas.?
View 2 Replies
View Related
Oct 17, 2012
when i connect Seagate 1 TB external harddisk to my computer ,initially the light is blinking up and then its stopped and note showingdetecting anywhere in computer(diskamanager too),is there anyway to make detect and recover my datas.?
View 1 Replies
View Related
Sep 28, 2012
I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.
But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.
I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.
View 4 Replies
View Related
Jun 28, 2011
I've recently purchased two 30GB SSDs which I have set up in a RAID 0 array and I have installed Windows onto these drives. I have a second, 2TB Seagate Barracuda Green HDD that I have used to put my user profiles and additional programs/games on as it wouldn't fit on the SSD.Everything was fine for a few days after installation. Then this morning I rebooted the computer and it just stalled on the flashing cursor (underscore) in the top left corner of the screen. I did the basic fixes (Windows repair, checking RAM) and nothing worked.Then I thought that I should try disconnecting all but the SSD with the OS on it. SUCCESS! It booted to Windows but couldn't find any programs/user data so it created a new "profile". I shutdown the computer and tried reconnecting just the data hard drive.I have two additional hard drives (used for backups) that don't affect anything at all when I plug them in.Does anybody know what could be the problem? I'm at a loss and I need the computer
View 3 Replies
View Related
Mar 1, 2010
How to Install and Setup a SATA Hard Drive ?
View 0 Replies
View Related
Jun 1, 2012
No success getting windows 7 to install with 2 TB sata hard drive. It reads on BIOS but when installer setup for W7 it stops in the beginning with "required cd/dvd driver missing"; asking you to go ahead and remove your installer disk for that particular step only.
View 1 Replies
View Related
May 10, 2012
i've been having some really weird freezes, sometimes its just the windows but multimedia keyboard keys / mouse still work, other times it completely freezes (cant even move the mouse.).Usually if i wait a little bit the computer goes back to normal by itself, other times i get BSOD.Im pretty sure its hardware related because i've tried formatting and got a bsod right after installing windows, i suspect the hard drive because when the computer freezes all HDD activity stops, when the computer manages to recover the hard drive activity comes back exactly at the same time the system unfreezes, sometimes if i run chkdsk there are lots and lots of errors, windows fixes them but they come back sooner or later, also, sometimes the computer doesn't detect the hard drive after a BSOD, turning the computer off and then on always "fixes" that tho.
The only reason im not 100% sure its the HDD its because all HDD utilities i've tried (incluiding western digital diagnostics software) say the disk is fine, can SMART be wrong I've also ran memtest and no errors (just one pass tho)Things seem to have gotten worse when i changed the graphic card, however i remember getting these freezes with the old one, just not as serious, prolly just a coincidence.I remember getting 3 kinds of BSOD errors: driver_power_state_failure, pagefault_in_nonpaged_area and kernel_data_inpage_error.A week ago i turned my pc on and windows was broken, startup repair thing would show up and try to repair but failed no matter how many times i tried, this never happened to me before so it must be related.
View 9 Replies
View Related
Aug 1, 2010
I installed Windows 7 32 bit ultimate edition to my acer notebook today. After taking my laptop to my office it didnt boot up. Taking so long to detect a hard drive. But when i press any key, it detect hardisk and boot up properly..
View 6 Replies
View Related
Jan 4, 2012
So my trusty old 40 GB Maxtor HDD finally died, and I'm trying to install Windows 7 on a 250 GB Western Digital Caviar SE 16 (SATA II). Windows will boot off of the DVD, load the setup, ask me if I want to perform an install or a repair, and then it asks if I want to upgrade or do a "custom" setup. I choose custom since it's a clean drive, but then it shows me a blank list of drives with the option to load a driver. My motherboard is a Gigabyte GA-G41M-ES2H, so I went to Gigabyte's website and downloaded the drivers and put them on a USB thumb drive. I spent hours trying to load different drivers to no avail. I tried the CD that came with the motherboard; no dice. I tried 32 and 64 bit installations; neither worked.
But you know what did work? My 180-day trial copy of Windows Server 2003. It detected that hard drive like Western Digital made it just for 2003.
View 9 Replies
View Related
Jun 8, 2011
Intel Core i7-960 3.20GHz LGA1366 CPU BX80601960
MB Intel BOX DX58OG
PSU Corsair 600W
MEM 4G KST KVR1333D3/4GR x3
EVGA GeForce GTX 560 Ti
Western Digital 500 GB SATA 6.0 GB-s Internal OEM Drive WD5000AAKX
Western Digital 2 TB Caviar Black SATA 6GB/s Internal OEM Drive WD2002FAEX
Just built this machine. Installed Windows 7 on the 500GB drive. Both drives are plugged into the blue SATA 6GB ports on my board. My drivers for these controllers are Marvell 91xx SATA 6G v1.2.0.1002 (Dated 3/7/2011). The second 2TB drive shows up in BIOS as well as Drive Management in Windows, but it will not be recognized as an accessible drive that can be formatted, partitioned, or anything. I get an error each time I attempt to format or partition through Drive Management. When I plug the 2TB drive into one of the other (black, Intel) SATA ports, the drive works fine, but in the blue ports it just won't seem to work. The 500GB drive, however, works perfectly as the boot disk in these ports.
View 9 Replies
View Related
Apr 28, 2012
I am trying to access my wife's macbook hard drive via my Windows computer using the Vantec SATA/IDE to USB 2.0 Adapter. The Apple techs said they could not get the drive to register when they hooked it up. However, we gave it a good drying with blow dryerThe adapter works fine and all the correct drivers installedI am in disk management and the 250GB drive seems to be showing up. However, it is not showing up in My Computer and right click shows "assign a letter" is grayed out.
View 2 Replies
View Related
Jan 30, 2010
I built a new computer. Rather expensive, but it should perform well. -Anyway-, I bought a brand new hard drive with the expectation of installing windows 7 on it and then working from there. The hard drive is recognized in the BIOS, the CMOS, and anything at all I've checked, but when I put the windows 7 64 bit disk in and try to do a custom install, seeing as I have nothing on the disk from which to upgrade, my hard drive does not show up in the section in which 7 asks where I want to install.
Motherboard is GIGABYTE GA-X58A-UD3R LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard, hard drive is Western Digital Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive.
The hard drive is plugged into the top SATA port (It has like, 10).
What can I do?
View 27 Replies
View Related
Sep 20, 2012
find a solution to how open sata slave and master hard drive on a desktop
View 1 Replies
View Related