Install everything, the bios detect the hard drive (it's a new hard drive, never been use) but when installing the Windows 7 64, the hard drive list is empty.
Here my spec
Phenom II 940BE | Gigabyte 790X-UD4P | Seagate Barracuda 7200.12 500GB | XFX HD4770 512MB | OCZ StealthXStream 600W | NZXT Tempest
Here's my hard drive: Seagate Constellation ES ST3500514NS
I haven't been able to get Windows 7 installation to detect this drive for about two months now. I'm running on a Gigabyte GA-880GA-UD3H mobo, revision 2.1.
I recently found a list of drivers for my motherboard on Gigabyte. I also found some downloads for my hard drive.
Oh, and I can use this drive if I'm running Windows 7 on a different hard drive, but I just can't install Windows 7 on it.
i've been having some really weird freezes, sometimes its just the windows but multimedia keyboard keys / mouse still work, other times it completely freezes (cant even move the mouse.).Usually if i wait a little bit the computer goes back to normal by itself, other times i get BSOD.Im pretty sure its hardware related because i've tried formatting and got a bsod right after installing windows, i suspect the hard drive because when the computer freezes all HDD activity stops, when the computer manages to recover the hard drive activity comes back exactly at the same time the system unfreezes, sometimes if i run chkdsk there are lots and lots of errors, windows fixes them but they come back sooner or later, also, sometimes the computer doesn't detect the hard drive after a BSOD, turning the computer off and then on always "fixes" that tho.
The only reason im not 100% sure its the HDD its because all HDD utilities i've tried (incluiding western digital diagnostics software) say the disk is fine, can SMART be wrong I've also ran memtest and no errors (just one pass tho)Things seem to have gotten worse when i changed the graphic card, however i remember getting these freezes with the old one, just not as serious, prolly just a coincidence.I remember getting 3 kinds of BSOD errors: driver_power_state_failure, pagefault_in_nonpaged_area and kernel_data_inpage_error.A week ago i turned my pc on and windows was broken, startup repair thing would show up and try to repair but failed no matter how many times i tried, this never happened to me before so it must be related.
So my trusty old 40 GB Maxtor HDD finally died, and I'm trying to install Windows 7 on a 250 GB Western Digital Caviar SE 16 (SATA II). Windows will boot off of the DVD, load the setup, ask me if I want to perform an install or a repair, and then it asks if I want to upgrade or do a "custom" setup. I choose custom since it's a clean drive, but then it shows me a blank list of drives with the option to load a driver. My motherboard is a Gigabyte GA-G41M-ES2H, so I went to Gigabyte's website and downloaded the drivers and put them on a USB thumb drive. I spent hours trying to load different drivers to no avail. I tried the CD that came with the motherboard; no dice. I tried 32 and 64 bit installations; neither worked.
But you know what did work? My 180-day trial copy of Windows Server 2003. It detected that hard drive like Western Digital made it just for 2003.
My mother asked me to fix her computer, his window XP is badly corrupted, so I tried to install Window 7 on her computer. However, the hard drive didn't show on the screen. I found it quite odd because BIOS detected it as IDE driver, and it's a SATA driver. I tried to install with old Window XP installation CD. Same thing, doesn't show on the window XP installation screen either.
I tried to hook hard drive on other computer, and was testing with Window 7 XD and see if it was working, and it did. It shown on the disk screen. My guess that it's probably the BIOS that occurred, or perhaps other things. I have one hard drive, nothing more.
I have a 2.8 Ghz, P4 processor with 768 (512 + 256) MB ram and an Asus p5rd1-vm motherboard with a 128 MB ATI-Radeon Graphics Card. I have been running Windows XP for years. I have decided to upgrade to Windows 7 finally after reading all the reviews. However, During installation, my hard disk is not being detected (There is no drive on screen which I can format or set up on.) Can anyone help? Do I need to update my BIOS?Also, I recently changed my hard disk (upgraded it) and XP has been installed and is running fine.
View 3 Replies View RelatedI got a laptop that's called a hp pavilion entertainment PC (dv67000) and it doesn't detect the hard drive nor the CD drive. I disconnected and reconnected them and reset BIOS to load default settings. And still nothing.
View 2 Replies View RelatedI have a 8 GB Transcend flash drive. I works properly on other systems (at least one system), but when I plug it in my Laptop, it is not even detected. Other USB devices work perfectly with my laptop, the only problem is with my Flash drive AND my laptop. I have tried to re install USB Hubs etc. of the laptop, but it did not help.
View 6 Replies View RelatedI am installing windows 7. but the installation cd won't recognized the hard drives but my bios does. i went to the website and looked up drivers for the wd2500s but they don't have them. they said that they use the software in windows to work. so is there any way to get the drives to work? i have three set up on raid 0
View 5 Replies View RelatedI have tried to use this IOMAX USB 2.0 to SATA/IDE Adapter Kit with Power: Amazon.co.uk: Electronics to connect an old 250 gb Samsung sata hard drive to my PC.Windows won't recognise it as a hard drive/partition - the USB adapter device is recognised, and via Devices & Printers, it shows the drive, but not as a USB External Drive, (see image) so I cannot access it.
View 3 Replies View RelatedOn my old secondary computer my setup was
Motherboard: Chaintech VNF2-350
Master 0: HDS722516VLAT80 with Windows installation
Slave 0: WD800BB-53CCB0
But then I started getting Machine Check Exceptions and my motherboard ultimately perished. So I replaced that with a Foxconn K8S755A-6ELRS. But this new motherboard won't detect the hard drive.
It will hang at the part that says "Detecting IDE drives", sometimes it will give up and display "0" where the drive is supposed to be, other times it will hang until you unplug the cable.
If it's on the same channel as the Hitachi drive with XP on it, the BIOS recognizes the other drive, but fails to boot from it. If they are on different channels, it boots the XP drive but will see no hint of the drive on the other channel., even in Disk Management or Device Manager.
I also tried connecting it to my other computer's Intel DP35DP mobo, and it was able to detect/read/write and all that, though it does have a few bad sectors.
Recently I change my Os from windows vista to 7. Because I can't find a way to make the original OS to become genuine.From there, my laptop can't read external hard drive but it can only read flash drives.I don't know what my laptop is missing, if it is updates or drivers.
View 8 Replies View Relatedi was installing window 7 and so far i have ubuntu installed but the set up could not detect any hard drive
View 3 Replies View RelatedI recently embarked on the journey of building my first custom PC. Everything was going well, until I hit a speed bump of installing Windows 7 64 bit. So like usual I boot from the CD drive, and stick Windows 7 in. When it gets to the point where I'm going to install, it is unable to find my SATA drive to install Windows 7 on.
It then asks me to "locate drivers." So it gives me an option to browse, and when it does so I put in the disk that came with my mobo, but it's unable to find any drivers. I tried downloading drivers from my motherboard's web site, sticking them on an external HD, and locating them from there, but that still didn't work.
I checked in my BIOS, and my SATA type is under Native IDE. I tried switching it to AHCI, and my HD was no longer detected in the BIOS, switched back to Native IDE and it found it again. Also, Onchip IDE Channel is set to Disabled, and Onchip SATA Control is set to Enabled, does this matter any?
I was wondering,though, is it possible that if I set the SATA type to AHCI, move the SATA cables into ports so that the drive is recognized by my BIOS, use the AHCI drivers I downloaded, Windows 7 will detect it?
When i connect Seagate 1 TB external harddisk to my computer ,initially the light is blinking up and then its stopped and note showingdetecting anywhere in computer(diskamanager too),is there anyway to make detect and recover my datas.?
View 2 Replies View Relatedwhen i connect Seagate 1 TB external harddisk to my computer ,initially the light is blinking up and then its stopped and note showingdetecting anywhere in computer(diskamanager too),is there anyway to make detect and recover my datas.?
View 1 Replies View RelatedI installed Windows 7 32 bit ultimate edition to my acer notebook today. After taking my laptop to my office it didnt boot up. Taking so long to detect a hard drive. But when i press any key, it detect hardisk and boot up properly..
View 6 Replies View RelatedI've had a sudden loss of my hard drive space. I've deleted alot of stuff, like over 20GB, more then just a few times and it just disappeared in less then 2 days. I've read some topics here with the about same problem and tried what they sugested there: to use software like WinDirStat, TreeSize Free and SpaceSniffer. But they just won't show me my whole hard drive. The stop at 50% and show it as if they have scan the whole 100%.
View 3 Replies View RelatedMe and my fiance just finished putting together her first real gaming computer and we wanted to use a Patriot 64g SSD to put win 7 on and use a 1TB Seagate drive for all the rest of the storage. The installation of Win 7 onto the SSD went nice and smooth but when we get into windows it is not detecting the 1TB HD at all. Funny thing is that when I go in to the SSD properties, I can see the Seagate under the sharing options. The only info I have found is how to clone off an existing hard drive with Win 7 on it not how to do a fresh install on 2 new drives.
View 1 Replies View Relatedwindows 7 pro 64 bit does not detect any hard drives - i have 4 sata - new install?
View 1 Replies View Relatedhow do I disable message that come while booting s m a r t hard drive detect error!
View 3 Replies View RelatedI just installed windows 7 on a home built desktop. Everything seems to be running fine except my 3rd hard drive won't show up. In device manager it shows all 3 hard drives, but in My Computer it only shows 2.
The hard drive that isn't showing up in My Computer (but showing up in Device Manager), is a Seagate Barracuda 7200.12 1 TB.
The hard drives that are showing up are both Seagate Barracuda 7200.11 but one is a 500 GB the other is a 750 GB.
I had Windows XP, then installed Windows 7 32bit Ultimate on IDE hard drive.
HOW CAN I FORMAT THE IDE HARD DRIVE SO AS TO DO A CLEAN INSTALL?
When putting CD in and pressing Intall. I wanted to Format my 40Gig IDE hard drive (that I use for windows intallation only). So as to start CLEAN install.
The CD recognised my hard drives. 250Gig SATA and 40Gig IDE....however would not let me format either or change in any way.....something about load driver?? VIA 6140 something.
So instead I thought to boot the disk and try that way. It didnt recognise the IDE hard drive at all. anyway I chose to do it the first way once I found that driver I mentioned.
I installed windows on woindows, then deleted the windows.old file afterwords.
I set the hard drive to stop spinning after 4 hours of idle activity but it doesn't ever go to sleep. If I set the time interval to < 1 hour like 45 min then it will go to sleep.
I'm not talking about the computer going to sleep/hibernating, I mean the spinning of the hard drive.
I have a laptop that is about a year old. Recently, my system rebooted and I was no longer able to view my Programs, files on the Hard drive or any other document. Here is the twist. I am still able to log into windows, use the Internet Explorere. If I happen to know the location of the file I can pull it up. It seems like i have no viewable rights to my C: drive at all. but can still work on files and programs.
View 1 Replies View RelatedI had an internet problem with windows 7 ultimate 64bit, so i decided to format it. I had one windows drive (SAMSUNG 250GB) and one storage drive (HITACHI 1TB) which has 900GB of important data on it. I chose custom installation onto my old windows drive (samsung) and it installed with no problems. I didn't touch my other drive. now, i can't see my 1tb storage drive in computers or in drive manager, but i can still see it in device manager! What should i do?? i really don't want to format it, but if the data is gone then i will have to.
View 5 Replies View RelatedI have a Seagate External Hard drive, Desk Goflex 3 TB.I'm using it for sevral mounth in windows 7 and it's working fine.Now, I bought a new latop using windows 7 as well, and it's not recognizing my hard drive.The hard drive doesn't appear in the Disk Management at all.The computer does recognize other USB devices (disk-on-keys, mouse).
View 1 Replies View RelatedI bought a new hard drive but toshiba said it isn't formatted correctly and now my drivers don't load
View 1 Replies View RelatedAny way i got this question i want to reinstall and i was wondering i got install files on D: ready and on C: i still got 7100 RC i want to install it on same drive if im not wrong old windows will be moved to folder windows.old right? so later i just delete windows.old and it will be fine right?
In earlier windows i could enter dos and click on setup exe and install from hd why its no longer possible
I have a WD My Book 110 External Hard Drive and when I plug it in and go to my computer to access the files on it the drive doesn't show, but if I go to the start menu and type b: in the search box it shows the files and the drive also shows in Disk Management, so why isn't it showing in My Computer and how can I get it to show?
View 9 Replies View RelatedMy only Windows DVD was an upgrade disk I used before on the same computer a few months before. I used the command prompt on the DVD to create a NTFS partition for the OS to load onto. After that everything installed and worked fine until I tried to activate use the upgrade key, it says that it can only be for upgrading and not clean installations. I was under the impression that since I already used the key to upgrade on the computer, I would be able to use it again. Will I need to buy a new install disk or will I be able to activate the OS another way? If I do need to buy a new install disk, would it be possible for me to simply find a X16-96072 Windows 7 Home Premium iso and use the activation code that my computer came with to provide the upgrade code with?
View 9 Replies View Related