BIOS Won't Detect IDE Hard Drive
Dec 30, 2011
On my old secondary computer my setup was
Motherboard: Chaintech VNF2-350
Master 0: HDS722516VLAT80 with Windows installation
Slave 0: WD800BB-53CCB0
But then I started getting Machine Check Exceptions and my motherboard ultimately perished. So I replaced that with a Foxconn K8S755A-6ELRS. But this new motherboard won't detect the hard drive.
It will hang at the part that says "Detecting IDE drives", sometimes it will give up and display "0" where the drive is supposed to be, other times it will hang until you unplug the cable.
If it's on the same channel as the Hitachi drive with XP on it, the BIOS recognizes the other drive, but fails to boot from it. If they are on different channels, it boots the XP drive but will see no hint of the drive on the other channel., even in Disk Management or Device Manager.
I also tried connecting it to my other computer's Intel DP35DP mobo, and it was able to detect/read/write and all that, though it does have a few bad sectors.
View 4 Replies
ADVERTISEMENT
Dec 18, 2011
I have tried to use this IOMAX USB 2.0 to SATA/IDE Adapter Kit with Power: Amazon.co.uk: Electronics to connect an old 250 gb Samsung sata hard drive to my PC.Windows won't recognise it as a hard drive/partition - the USB adapter device is recognised, and via Devices & Printers, it shows the drive, but not as a USB External Drive, (see image) so I cannot access it.
View 3 Replies
View Related
Jul 22, 2012
Recently I change my Os from windows vista to 7. Because I can't find a way to make the original OS to become genuine.From there, my laptop can't read external hard drive but it can only read flash drives.I don't know what my laptop is missing, if it is updates or drivers.
View 8 Replies
View Related
Nov 8, 2011
i was installing window 7 and so far i have ubuntu installed but the set up could not detect any hard drive
View 3 Replies
View Related
May 14, 2009
Install everything, the bios detect the hard drive (it's a new hard drive, never been use) but when installing the Windows 7 64, the hard drive list is empty.
Here my spec
Phenom II 940BE | Gigabyte 790X-UD4P | Seagate Barracuda 7200.12 500GB | XFX HD4770 512MB | OCZ StealthXStream 600W | NZXT Tempest
View 2 Replies
View Related
Feb 17, 2011
Here's my hard drive: Seagate Constellation ES ST3500514NS
I haven't been able to get Windows 7 installation to detect this drive for about two months now. I'm running on a Gigabyte GA-880GA-UD3H mobo, revision 2.1.
I recently found a list of drivers for my motherboard on Gigabyte. I also found some downloads for my hard drive.
Oh, and I can use this drive if I'm running Windows 7 on a different hard drive, but I just can't install Windows 7 on it.
View 5 Replies
View Related
Dec 20, 2009
I recently embarked on the journey of building my first custom PC. Everything was going well, until I hit a speed bump of installing Windows 7 64 bit. So like usual I boot from the CD drive, and stick Windows 7 in. When it gets to the point where I'm going to install, it is unable to find my SATA drive to install Windows 7 on.
It then asks me to "locate drivers." So it gives me an option to browse, and when it does so I put in the disk that came with my mobo, but it's unable to find any drivers. I tried downloading drivers from my motherboard's web site, sticking them on an external HD, and locating them from there, but that still didn't work.
I checked in my BIOS, and my SATA type is under Native IDE. I tried switching it to AHCI, and my HD was no longer detected in the BIOS, switched back to Native IDE and it found it again. Also, Onchip IDE Channel is set to Disabled, and Onchip SATA Control is set to Enabled, does this matter any?
I was wondering,though, is it possible that if I set the SATA type to AHCI, move the SATA cables into ports so that the drive is recognized by my BIOS, use the AHCI drivers I downloaded, Windows 7 will detect it?
View 5 Replies
View Related
Oct 17, 2012
When i connect Seagate 1 TB external harddisk to my computer ,initially the light is blinking up and then its stopped and note showingdetecting anywhere in computer(diskamanager too),is there anyway to make detect and recover my datas.?
View 2 Replies
View Related
Oct 17, 2012
when i connect Seagate 1 TB external harddisk to my computer ,initially the light is blinking up and then its stopped and note showingdetecting anywhere in computer(diskamanager too),is there anyway to make detect and recover my datas.?
View 1 Replies
View Related
May 10, 2012
i've been having some really weird freezes, sometimes its just the windows but multimedia keyboard keys / mouse still work, other times it completely freezes (cant even move the mouse.).Usually if i wait a little bit the computer goes back to normal by itself, other times i get BSOD.Im pretty sure its hardware related because i've tried formatting and got a bsod right after installing windows, i suspect the hard drive because when the computer freezes all HDD activity stops, when the computer manages to recover the hard drive activity comes back exactly at the same time the system unfreezes, sometimes if i run chkdsk there are lots and lots of errors, windows fixes them but they come back sooner or later, also, sometimes the computer doesn't detect the hard drive after a BSOD, turning the computer off and then on always "fixes" that tho.
The only reason im not 100% sure its the HDD its because all HDD utilities i've tried (incluiding western digital diagnostics software) say the disk is fine, can SMART be wrong I've also ran memtest and no errors (just one pass tho)Things seem to have gotten worse when i changed the graphic card, however i remember getting these freezes with the old one, just not as serious, prolly just a coincidence.I remember getting 3 kinds of BSOD errors: driver_power_state_failure, pagefault_in_nonpaged_area and kernel_data_inpage_error.A week ago i turned my pc on and windows was broken, startup repair thing would show up and try to repair but failed no matter how many times i tried, this never happened to me before so it must be related.
View 9 Replies
View Related
Aug 1, 2010
I installed Windows 7 32 bit ultimate edition to my acer notebook today. After taking my laptop to my office it didnt boot up. Taking so long to detect a hard drive. But when i press any key, it detect hardisk and boot up properly..
View 6 Replies
View Related
Jan 4, 2012
So my trusty old 40 GB Maxtor HDD finally died, and I'm trying to install Windows 7 on a 250 GB Western Digital Caviar SE 16 (SATA II). Windows will boot off of the DVD, load the setup, ask me if I want to perform an install or a repair, and then it asks if I want to upgrade or do a "custom" setup. I choose custom since it's a clean drive, but then it shows me a blank list of drives with the option to load a driver. My motherboard is a Gigabyte GA-G41M-ES2H, so I went to Gigabyte's website and downloaded the drivers and put them on a USB thumb drive. I spent hours trying to load different drivers to no avail. I tried the CD that came with the motherboard; no dice. I tried 32 and 64 bit installations; neither worked.
But you know what did work? My 180-day trial copy of Windows Server 2003. It detected that hard drive like Western Digital made it just for 2003.
View 9 Replies
View Related
Nov 17, 2011
I've had a sudden loss of my hard drive space. I've deleted alot of stuff, like over 20GB, more then just a few times and it just disappeared in less then 2 days. I've read some topics here with the about same problem and tried what they sugested there: to use software like WinDirStat, TreeSize Free and SpaceSniffer. But they just won't show me my whole hard drive. The stop at 50% and show it as if they have scan the whole 100%.
View 3 Replies
View Related
Feb 20, 2012
Me and my fiance just finished putting together her first real gaming computer and we wanted to use a Patriot 64g SSD to put win 7 on and use a 1TB Seagate drive for all the rest of the storage. The installation of Win 7 onto the SSD went nice and smooth but when we get into windows it is not detecting the 1TB HD at all. Funny thing is that when I go in to the SSD properties, I can see the Seagate under the sharing options. The only info I have found is how to clone off an existing hard drive with Win 7 on it not how to do a fresh install on 2 new drives.
View 1 Replies
View Related
Dec 18, 2011
windows 7 pro 64 bit does not detect any hard drives - i have 4 sata - new install?
View 1 Replies
View Related
Feb 14, 2012
how do I disable message that come while booting s m a r t hard drive detect error!
View 3 Replies
View Related
Apr 30, 2012
My hard drive, a WD Scorpio 200GB, is not being detected in bios. AHCI mode is enabled. When I go into the Advanced BIOS Features, all the master and slave configs are none; however, my SSD is recognized as I am on my computer right now using it. I tried every SATA Port, EVEN THE SATA PORT MY SSD IS INSTALLED ON, and it doesn't work; I tried 2 different cables and still no recognition; I tried 4 different hard drives and still no recognition, so it is not a problem with my motherboard, hard drives, or cables. What should I do? I have been trying to figure this out for 4 hours.
View 7 Replies
View Related
Jul 24, 2012
i need to completely remove all from my hard drive so that i can run my restore discs i purchased from gateway- my computer is 6 mos old and came without dics as it had restore capabilities pre installed from factory.
View 2 Replies
View Related
Oct 12, 2011
I have had an expensive time with my computer recently but i am now beyond the brink and turning the tide of war to my favour.I have recently kitted my ailing PC out with a new SSD for the OS install.This is working great; i have just tonight had to plug in a brand new GFX card for my gaming pc.(My GFX card burned out due to overheating, so i have now got a new case and proper cooling)Basically, my secondary hard disk (Files Storage etc) is not working, when plugged into my sata port my computer hangs at the Windows Loading screen, also i cannot get into the BIOS.If i unplug the hard drive (Not SSD, 500GB Hitachi) my computer boots in 14 seconds, and the bios works fine.I have concluded my secondary hard disk may be broken.if i can fix it as i can barely afford to buy a new one (even knowing they are cheap).Basically if it had broken i would expect my PC would say so, seems to me that it is just waiting for a response and sitting around for hours to get it
View 4 Replies
View Related
Jul 5, 2011
Working on my friends desktop computer and the BIOS doesn't detect the hard drive all the time. If I cold boot or reset the machine the hard drive is not detected. However if I pull the CMOS battery and power cord then drain the capacitors (by pressing the power button) and replug the power the drive is detected by the BIOS and starts booting windows (then freezes). The Computer can boot from CDs fine (from IDE cd drives). When I power up the machine without draining all of it's power/ removing the power cord the BIOS gets stuck detecting the SATA drive. I tried the Hard drive in my machine it and worked fine so I don't think its a drive/cable problem. I also tried one of my known good WD drives in the machine and it doesn't detect it. I have tried replacing the signal cable. Default settings (no options for IDE/AHCI just enable or disable SATA). I'm not sure if windows freezing is a 2nd problem or part of the first.
Motherboard: Gigabyte GA-k9ns Version F9
Drive: seagate 500gb sata (also tried a WD green 500gb & black 1TB)
View 5 Replies
View Related
Sep 28, 2012
I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.
But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.
I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.
View 4 Replies
View Related
Aug 29, 2009
I just installed the RC last night and everything was going okay until I restarted my computer and my backup drive disappeared. It was accessible until I restarted, I didn't install any new drivers.
It's an IDE drive.. it doesn't show up in Disk Management either so I'm kind of stuck at what to do. Any ideas?
View 2 Replies
View Related
Dec 9, 2009
hard drive registers in BIOS, but not in the windows 7 Ultimate 64 bit installation screen. Any questions I will answer RIGHT away. Oh dear God please help me. I took it in to a repair shop and I think I knew more than they did and left without any substantive help (but a $40 bill ). Do I need to format the HD? Would drivers help? All the websites say everything should be compatible - no problem - but nothing here.
WD Blue 640 GB (single HDD)
AMD Phenom ii
GA-MA785GM-US2H Gigabyte motherboard
OS: Windows 7 Ultimate 64 bit
View 4 Replies
View Related
Nov 16, 2012
recently had a few parts die on me so i have started to rebuild a whole new comp my motherboard is a asrock 970 extreme3 cpu is a fx 8-core black edition and gpu is a gigabyte hd7850 2g gddr5 with a seagate 1tb barricuda 7200 hdd now thats out of the way my problem is im trying to reinstall win7 but neither my bios or win 7 rrecognising my hard drive i get stuck at where it asked me where i want to install it to i try load drive but as i said
View 1 Replies
View Related
Oct 11, 2012
My Acer netbook has developed some kind of fault and I am unsure as to what I ought to do. The netbook does boot to BIOS and also will boot up from an external drive...but will not boot normally. I am thinking of replacing the hard drive but don't know if there could be something else wrong. It says sometimes that it can't read it and from this I am not sure if there is something else wrong. If I change the drive does it sound as though things will work? There are also a couple of other intermittent faults such as certain letters and numbers not working and then everything is fine for a while...
View 4 Replies
View Related
Aug 27, 2011
I'm currently using a Windows 7 PC built by a friend of mine, but starting yesterday, its been acting up. The problem is there used to be two hard drives I can access, Drive B and Drive C. When I boot up the computer, BIOS only detects Drive C (if I'm not mistaken), and Disk Managements as well. I realized this when all the programs whose targets are on that drive are all broken on the desktop.So Drive B doesn't show up anywhere at all.
View 29 Replies
View Related
Apr 13, 2012
Lots of BSOD, lock ups, hard drive not being detected by bios, is it failing? Let me start by saying my PC is custom built, most parts are only a year old. The oldest parts are the harddrive (about 5 years) and the soundcard (about 7 years). I have never had major problems until now (a year after building it).
It all started with a blue screen.
KERNEL_DATA_INPAGE_ERROR
Reboot windows and it seems to start up fine, gets to the desktop and locks up.
Reboot windows and I get another blue screen.
BAD_SYSTEM_CONFIG_INFO
I try to start windows from the last good configuration. Error. Registry file failure. Cannot load hive file. I try booting from the windows cd and running a chkdsk. Hard drive starts making a buzzing sound. It gets to step 3 of 5 and stops. Failed to transfer logged messages. Status 50. Now the bios rarely even "sees" the drive. When I can get it to boot and see it, any attempt at diagnostics and repairs produces errors, locks up, or fails.
Is this a bad hard drive? I would hate to spend the money on a new one only to find it is a bad mobo or virus. How can I diagnose this? If it is a bad drive I would like to save what juice is left in it and try to recover a few files before it dies. Most of the important data has been backed up but I would like to try and get a few game save files if I can. But its not a disaster if the drive data is not recoverable.
View 3 Replies
View Related
Jul 28, 2011
i have Acer computer,was working fine ,yesterday frozen while iam at net, and i turnoff by pressing holding the power buttom, after that comes message: reboot and select proper device i couldnt open the recovery by pressing f10 and the hard drive and the dvd missing from bios not detected.
View 5 Replies
View Related
Nov 13, 2011
I use Transcend external DVDwriter Modell TS8X DVDR-K on Dell Inspiron 1520 In Windows, there is no problem and i use it easily, but the bios does not recognize it and i can t boot any cd from it. I am saying that bios does not detect my external hard drive, but only my original dvd- rom.And as i said, windows detects it easily , but not Bios !
View 5 Replies
View Related
Jul 17, 2011
THE TITLE IS MY QUESTION...DRIVE HAD VISTA ON IT FOR YRS BOOTED WIN 7 CD AND CHOOSE TO DELETE PARTITIONS..I LET IT CREATE THE BACK UP PARTITIONS WITH 12GBG A 100mb AND THEN THE NISTALLATION PORTION..I INSTALLED..AFTER A REBOOT..DRIVE NEVER DETECTED AGAIN...WHEN ITS PLUGGED IN IOT FREEZES MY BOOT UP..CANT ACCCESS BIOS WHEN DRIVE PLUGGED IN..UNPLUG SERIAL CABLE..ALL IS WELL.
View 4 Replies
View Related
Jan 6, 2013
So What i am saying is whenever i boot up my computer there is a black with white text screen that says something about an unconfigured hard drive that is in my computer. But then again whenever i am on my desktop doing whatever i can use it perfectly fine. Also it does not show up in the bios. it just has my boot up drive and my optical drive.
View 1 Replies
View Related
