THE TITLE IS MY QUESTION...DRIVE HAD VISTA ON IT FOR YRS BOOTED WIN 7 CD AND CHOOSE TO DELETE PARTITIONS..I LET IT CREATE THE BACK UP PARTITIONS WITH 12GBG A 100mb AND THEN THE NISTALLATION PORTION..I INSTALLED..AFTER A REBOOT..DRIVE NEVER DETECTED AGAIN...WHEN ITS PLUGGED IN IOT FREEZES MY BOOT UP..CANT ACCCESS BIOS WHEN DRIVE PLUGGED IN..UNPLUG SERIAL CABLE..ALL IS WELL.
View 4 Replies
i have Acer computer,was working fine ,yesterday frozen while iam at net, and i turnoff by pressing holding the power buttom, after that comes message: reboot and select proper device i couldnt open the recovery by pressing f10 and the hard drive and the dvd missing from bios not detected.
View 5 Replies View RelatedI have a Z68 AP D3 gigabyte mother board with Smart Responce capable. I have a 1 t sata HD and a 64 SSD. Trying to set up Smart Response.
Gigabyte show a simple video to make it work. But not working for me. As soon as the bios are set to xHD, my windows no longer works. It say operation system is missing. But after change back to AHCI, windows works again.
Installing Intel Smart Response also cause Windows to crash. At boot up, the intial 4 lights that forms the window logo at boot up freeze, then the death blue screen shows up. Need to repair windows again.
Tried setting bios to xHD and install new windows, but windows cannot recogize any of the HD while on xHD. Drivers for RAID found on my motherboard CD does not work either.
Tried to change cables to Sata 3 port only, also not working. Sata port 2 also not working. why cant' my system read xHD configuration? Am I missing a module or hardware?
So I am here because I am having some hard drive problems. Firstly for my Primary drive i am still running my old 250gb Hard drive (with windows already installed on this drive). Secondly, for my slave drive i have a Samsung Spinpoint 1TB Hard drive that wont display in my bios or in disk management. The 1TB drive seems to spin up fine etc. but i just can get it to display. i can format this new disk. Also i must add that my motherboard is an ASUS p8z68-v-pro board.
View 9 Replies View RelatedJust built a moderate spec gaming PC from scratch, and all has went according to plan except when I try to install Windows 7, my hard drive won't show up. My new motherboard doesn't have any IDE slots, but I only have an IDE hard drive. I am using a 'Pluscom Serial ATA PCI Adapter' to connect my hard drive to the computer as it has 1 IDE slot on it. I don't have a disc for drivers and don't know where to start. I am running Ubuntu on it at the moment so I can download any drivers I may need.
View 9 Replies View RelatedI recently embarked on the journey of building my first custom PC. Everything was going well, until I hit a speed bump of installing Windows 7 64 bit. So like usual I boot from the CD drive, and stick Windows 7 in. When it gets to the point where I'm going to install, it is unable to find my SATA drive to install Windows 7 on.
It then asks me to "locate drivers." So it gives me an option to browse, and when it does so I put in the disk that came with my mobo, but it's unable to find any drivers. I tried downloading drivers from my motherboard's web site, sticking them on an external HD, and locating them from there, but that still didn't work.
I checked in my BIOS, and my SATA type is under Native IDE. I tried switching it to AHCI, and my HD was no longer detected in the BIOS, switched back to Native IDE and it found it again. Also, Onchip IDE Channel is set to Disabled, and Onchip SATA Control is set to Enabled, does this matter any?
I was wondering,though, is it possible that if I set the SATA type to AHCI, move the SATA cables into ports so that the drive is recognized by my BIOS, use the AHCI drivers I downloaded, Windows 7 will detect it?
I assembled a new computer using:
Windows 7 64bit Pro SP1 OEM System Builder Pack
Gigabyte H77M-D3H
1TB SATA HDD WD Caviar Black
Intel Core i3 2125
DDR3 8GB 1600 Intel Viper
SATA LG Blue Ray DVDRW
Clean install of Windows reveals an error not detecting any drives, does not allow partitioning or formatting. BIOS identifies the drives.I've attempted installs of updated drivers from the motherboard's website (as well as the CD that came with the motherboard). WD claims not to have any drivers on their website. Still nothing.
windows 7 pro 64 bit does not detect any hard drives - i have 4 sata - new install?
View 1 Replies View RelatedI use Transcend external DVDwriter Modell TS8X DVDR-K on Dell Inspiron 1520 In Windows, there is no problem and i use it easily, but the bios does not recognize it and i can t boot any cd from it. I am saying that bios does not detect my external hard drive, but only my original dvd- rom.And as i said, windows detects it easily , but not Bios !
View 5 Replies View RelatedOn my old secondary computer my setup was
Motherboard: Chaintech VNF2-350
Master 0: HDS722516VLAT80 with Windows installation
Slave 0: WD800BB-53CCB0
But then I started getting Machine Check Exceptions and my motherboard ultimately perished. So I replaced that with a Foxconn K8S755A-6ELRS. But this new motherboard won't detect the hard drive.
It will hang at the part that says "Detecting IDE drives", sometimes it will give up and display "0" where the drive is supposed to be, other times it will hang until you unplug the cable.
If it's on the same channel as the Hitachi drive with XP on it, the BIOS recognizes the other drive, but fails to boot from it. If they are on different channels, it boots the XP drive but will see no hint of the drive on the other channel., even in Disk Management or Device Manager.
I also tried connecting it to my other computer's Intel DP35DP mobo, and it was able to detect/read/write and all that, though it does have a few bad sectors.
I installed an old 160GB Seagate Barracuda into my Win7Pro64 machine for some extra storage room. At first it worked fine. I cleaned it out and did a quick format in Windows.
Now Windows does recognize it at all. I see it in the BIOS but it won't show up in Windows.
My pc had suddenly decided to not recognising any of my Sata drives. Win 7 32 bit, 4 gig ram, asus psn d motherboard,ati sapphire 1g pci card, 1 250g western digital Sata drive 1 x 1tb seagate hdd. Sata DVD drive
Yesterday my pc froze up while surfing the web, so reset it and that where the problems started
It only recognised one of the hdd then wouldn't boot got a bsod uncountable boot volume. So opened up the case to check if the cables where loose, nope, so decided to run a repair via the recovery console. Didnt detect my o/s at all ask me to install the correct drivers grrrrr. So stripped the pc down swapped the Sata cables to see if that was the problem, no joy at all would only find one Sata drive and DVD drive. Then it wouldnt recognise any of them, so swapped out the Sata DVD drive for an IDE drive. The booted up nothing bar the DVD drive. Have now come to a cross roads don't know what else's to try. Managed to boot via a USB drive with Linux and everything system wise, pcu, gpu etc works, but still no Sata drives.
Done some digging online and some ideas are not a big enough psu, faulty Sata cables, but swapped in an IDE hdd and nothing again.
it was working before the BIOS Update My Board is Intel DG31PR Updated to the [URL] and i dont remember the old BIOS version?
View 2 Replies View RelatedIt was working before the BIOS Update My Board is Intel DG31PR Updated to the (http://downloadcenter.intel.com/Deta...=2839&lang=eng) and i dont remember the old BIOS version
View 2 Replies View RelatedWhen I open the PC, my hardrive and DVD rom was detected in bios but when the operating system started it shows the windows logo then after a second it shows a message that "the driver not found. Im confuse because i have only one hardrive which is the win7 installed on it. How can possibly that the PC did not find this driver but it shows the logo of win7?
View 1 Replies View RelatedI have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.
But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.
I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.
Synopsis: PSU died, replaced PSU with different model, system boots to bios successfully but does not recognize any devices in SATA ports, nor do those devices appear to be getting power. Now can't even get to BIOS, entire PC flicks on and off repeatedly as soon as I turn the PSU on regardless of whether I hit the power button on the front of the computer.
System Specifications
Original PSU that died: SeaSonic M12II 750 SS-750AM 750w PSU
CPU: Intel Core i5-3570K Ivy Bridge 3.4GHz
GPUs: ASUS 670 non-top version, SLI (2x)
MOBO: ASRock Z77 extreme 6
RAM: Mushkin Enhanced Blackline 8GB (2 x 4GB) SDRAM DDR3 2133
Optical drive: Sony AD-7280S-0B 24x SATA Internal DVD+/-RW Drive
SSD: SanDisk Extreme 240GB SATA 6.0 Gb-s 2.5-Inch (OS is installed here)
Storage drive: Western Digital Caviar Black 1 TB SATA III (This was not connected when power supply died)
Detailed explanation:About a week ago my PSU (Seasonic 750w) died randomly while the computer was left running in sleep . I RMA'd the dead seasonic. In the mean time I happened to come accross an extremely good deal on a new PSU, so I bought it (Thermaltake smart m850w PSU) to have a backup and to get my machine working again. I hooked up the new PSU to GPUs, CPU, fans, ATX power connector, and to all of the SATA devices, (the SSD, the HDD, and the Optical drive). I made sure to connect the data cables to the SATA devices in the same configuration they were in when working properly. The computer boots successfully to the ASROCK BIOS, all fans spinning. However, I get the error code "A6" on "dr debug" (the led display on the mobo). The manual says this means "SCSI detect". I have no idea what that means.
I was able to load the UEFI, and bios recognized all components except for any of the SATA devices--(SSD, the HDD, and optical drive not recognized). The RAM, GPUs, processor, and fans were detected. At this point I was stuck in BIOS because I couldn't boot off anything.I did not have the HDD connected when the PSU failed, but now the BIOS won't read that either. I don't think any of the SATA devices are actually receiving power. Again, the UEFI showed that there were no SATA devices connected to any port, when in reality they clearly were connected both by power and data cable. Then things get really strange. I unhooked all of the SATA devices except the HDD (the one that wasn't hooked up when the original PSU died). I plug the AC into the PSU, then turn on PSU (not the power switch for the computer, the switch on the PSU). The computer starts flicking on and off in this weird rhythmic pulsating pattern "click...click...click...click..." with about a 1/2 second between each click. Each time the power flicks on, the LEDs come on and the fans spin briefly. The strangest part is that I don't need to hit the power button on the front of the case for this to happen, it just starts as soon as the PSU is turned on. In fact, I can't get the computer to turn on at all--the switch on the front of the computer appears to be dead.
1. Unplug the power cables from everything and re-seated them.
2. Reseated the data cables to the optical drive and the SSD on the drive end, not on the MOBO side as they are covered by my GPUs and I would have to take them out in order to do that.
3. Tried hooking up a SATA power cable from my old modular PSU and using that in the new PSU in an attempt to power the optical drive (didn't work, I know, bad idea--I learned you aren't supposed to do this shortly after I tried it)
4. Setting all preferences to default in the UEFI.
5. Disconnecting the power cables from one or both of the GPUs.
I think that this is either a problem with (1) the motherboard, (2) the new PSU, (3) all 3 SATA devices (unlikely). The fact that I can't even get into Bios anymore tells me that this may be a MOBO or PSU issue.My main question is how to procede from here? I suppose I can wait for my Seasonic to come back from RMA--perhaps that will clear up the issue. I just can't shake the feeling that this is a MOBO issue though. I am worried that if I keep screwing around with it I may end up frying my CPU and GPUs. I can eat the cost of a MOBO or PSU if necessary, but I can't afford to buy a new processor and two new 670s.
I'm going to install RC1 in the next few days.
I was looking to test the stability within RC1 of an adaptec 1220SA card I have to control the system drives. I have the Vista 64bit driver for the card as this is the newest listed.
I have created a recovery disc in beta build 7000 and hope to use this to boot into a DOS shell and follow the instructions given on the adaptec site:
This is the BIOS release v6.0-0 Build 2330 for the Adaptec SATA II RAID 1220SA Controller.
This BIOS should only be used together with Driver v1.6.12086 in Windows Server 2008 or Windows Vista.
This self-extracting archive includes the flash utility, the BIOS image file and the Release Notes.
Caution: If the BIOS update fails with an error message "unable to find file" or "target controller does not match", please see ASK Answer ID 15241
Installation Instruction: This file is self extracting and will unzip to the directory adaptec1220sa. Copy the expanded files to a floppy diskette. The expanded files can also be copied to a USB device or CD-R.
Shut down the operating system and reboot to DOS from a bootable floppy disk, USB device or CD-R. Insert the media with the update files. Run the flash utility program named AFU.EXE included in this download to backup the current BIOS and flash the new BIOS image.
I'm hoping to expand the bios update file onto a cd for the second drive or alternatively stick it on a USB stick.
My question is this, when I am in the dos shell, what do I do!
I suddenly realised that i've never had a need to use the command line
I just changed my disk setup from:
1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
I was on vacation for 1 month and after that my PC suddenly did a check to 1 of my HDD's (Samsung 1000GB HDD - My storage drive that sometimes I just don't see in system anymore and system restore fixes the problem usually). After that check, my PC worked fine whole day, but the next day i Turn it on (After installing about 7-8 Important windows updates) I don't see my Samsung HDD, So I thought it's a usual problem that I have, I notice that the only restore points I have are from year 2011... That didn't suit me and I thought why do I have restore points so far behind ? But then I notice 1 more important update if I shut down my PC, So I thought it might fix the problem and maybe create another restore point for me. That's where I shut down my PC and start it again. Now it takes a lot longer in my BIOS and I notice that it doesn't detect any of my HDD's and asks for boot disk after that. Now I'm clueless what to do, since the problem I had was only with 1 HDD that had lesser rpm than my other one that i use for my system (Also it was the cheapest 1000GB HDD that I have seen long time ago and seems to have a lot of problems)
OS Windows 7 32-bit RAM 3GB (1GB + 2GB) Mobo (I don't know exact module but i write what was written in BIOS) Intel I945 for 945GZM-S2 F2 also i Know its from GIGABYTE HDD's: 1x 120GB 7200rpm with 3 partitions, 1x SAMSUNG 1TB (1000GB) HDD with 5400rpm CPU Intel Dual core 2.00GHZ
I haven't tried anything much other than pressing delete key and configuring BIOS... they were set to default nothing helped there + It doesn't detect multiple HDD's. the PSU is new and probably had same Voltage or even more I don't remember exactly which one of those.
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?
View 9 Replies View Relatedi want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7
View 4 Replies View Relatedi purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
View 5 Replies View RelatedMy MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?
View 5 Replies View Relatedi'm looking to upgrade from a HDD to SSD. I've been reading online about my board and apparently the marvell 9128 controller sucks speed wise. I was looking at the Corsair Force 3 because of the read/write speeds. Upon doing more digging though it looks like id be better off running a drive on the SATA 2 ports.
View 2 Replies View RelatedThe hard drive in my son's laptop has died, it's a SATA 1 (1.5Gb/s) drive. Can I upgrade it to a SATA 2 (3.0 Gb/s) hard disk?? It's in a Toshiba laptop.
View 7 Replies View RelatedI was wondering If I have one sata 1 and an new sata 2(or 3) on my PC installed on my PC will cause problems in transfer speeds? My Blue-ray is sata 1 also.Does this mean that all disks will work as sata 1?
View 2 Replies View RelatedI've got an Acer Model As5742 Laptop with an i5 480M processor and 8 GB of good Ram. I'm running Win 7 Pro 64 Bit. It's only about 5 months old and this started about a month ago. I have no other problems. IE: Blue Screens or Lockups or anything, just the Bios clock changes to a random date and time after every restart. I replaced the Bios battery twice and it only effects the chore of having to reset the time in Windows every time I boot.
I'm going to send it to Acer to be repaired within a week or two, but maybe it's not a bad timing mechanism in the motherboard and one of you people have a correct solution to it. Which will save me the trouble of sending it in for a motherboard replacement.
I do have all the drivers and bios updates installed. Oh yes I've ran about 15 different virus Etc. Malware scans with several different products and they all come back clean. I ran System File Checker SFC /scannow from the command prompt several times that also comes back OK.
so i did a bios update, and it wont boot after the update.its a asus m4a79xtd evo (rev 1.01g)i dont have a backup of the bios
View 3 Replies View RelatedIt worked fine on Windows Vista. I just formated the first and installed Windows Seven on it. Now when loading up Seven, it says the 2nd is installed and working, but its not accessible and doesnt even appear.
View 1 Replies View Related
