I was wondering If I have one sata 1 and an new sata 2(or 3) on my PC installed on my PC will cause problems in transfer speeds? My Blue-ray is sata 1 also.Does this mean that all disks will work as sata 1?
View 2 Replies
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?
View 9 Replies View Relatedi want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7
View 4 Replies View Relatedi purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
View 5 Replies View RelatedMy MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?
View 5 Replies View Relatedi'm looking to upgrade from a HDD to SSD. I've been reading online about my board and apparently the marvell 9128 controller sucks speed wise. I was looking at the Corsair Force 3 because of the read/write speeds. Upon doing more digging though it looks like id be better off running a drive on the SATA 2 ports.
View 2 Replies View RelatedI'm trying to install from a sata dvd drive onto an ide hard disc. I have the raid drivers for my board, x64 vista drivers to be exact.
During the install sequence I obviously get to the bit that asks me to insert a driver disc for the dvd drive. Currently the drivers are on a floppy, so insert the floppy disc and browse to the drivers. windows 7 then starts to load the drivers them fails with a message stating it can't find find drivers for this drive.
Has anyone else tried installing from a sata drive, and if so how did you get on?
i have a HP g61 with a 500 gig SATA drive when i try to install windows XP on it i get a windows stop messsage
Stop: 0x0000007b (0xf78d663c, 0x00000034, 0x00000000,0x00000000)
when googled it says something about the sata drive settings needing to be changed in the bios chang the setting for the sata operation from Raid auto/achi to raid auto ata but in the bios of the hp g61 there is no option for that, i verified this will work for the error because i just restored a dell vostro with a sata drive and it did work, now i just need to get this hp to work it has insydeH20 bios setup utility,
I want to install win 7 professional x64,i have a Dvd iso...Problem i want to solve is next,i have 1 sata disk ,and 1 ide disk...I want to divide Sata on two partition,c and d,and to install system on c..Next,my Ide disk ,has jumper on cable select,i think it could be the only way that is to pc work properly.Problem is ,when i install win 7 on partition c,next happens ,on My Computer,disk drives are not shown as Sataartitions c: and d: but its mixed somewhat,if i recall,itc c: of sata,and d is given t ide disk... i really want to know is there a solution to have primary sata c: and d: ,and than ide diskProcessorModel : AMD Athlon(tm) 64 X2 Dual Core Processor 4600+Speed : 2.57GHzCores per Processor : 2 Unit(s)Threads per Core : 1 Unit(s)Type : Dual-CoreIntegrated Data Cache : 2x 64kB, Synchronous, Write-Back, 2-way, Exclusive, 64 byte line sizeL2 Cache : 2x 512kB, ECC, Synchronous, Write-Back, 16-way, Exclusive, 64 byte line size[CODE]
View 2 Replies View RelatedI have Win 7 x86 Enterprise through the company I work with. I was in charge of beta testing it on partition in the SATA raid array on our SunFire v20z server. It installs like it would on any other computer, does not hang up, and reboots to finish install. when it boots however, it shows win7 boot screen, then goes blank, then restarts computer. when i boot into safe mode it hangs on disk.sys and then BSODs. can someone please tell me what is going on?? I have invested over 2 weeks of work into setting it up.
View 2 Replies View RelatedThe hard drive in my son's laptop has died, it's a SATA 1 (1.5Gb/s) drive. Can I upgrade it to a SATA 2 (3.0 Gb/s) hard disk?? It's in a Toshiba laptop.
View 7 Replies View RelatedI'm getting ready to remove Windows 7 RC and install my legit copy of Windows 7 on my PC. My version of Windows 7 is a XP Pro -> Windows 7 Pro upgrade. When I did this upgrade on my laptop, I ran into a bunch of SATA issues because Windows XP does not support SATA on the default installation disk. Needless to say, a few hours later of messing with nLite, my laptop is good to go.
I want to avoid this mess with my PC and already be prepared. I'm trying to figure out what SATA drivers I need to use with nLite for my main PC. Is there somewhere I can go to get this information? Are the drivers based off my motherboard? CPU? Hard drive? Not sure where to start. My laptop's SATA drivers seemed to be based off the CPU (AMD) going by the name of the driver file.
Mobo: GIGABYTE GA-EP45-UD3P LGA 775 Intel P45 ATX Intel Motherboard
CPU: Intel Core 2 Quad Q9550 Yorkfield 2.83GHz LGA 775 95W Quad-Core Processor Model BX80569Q9550
RAM: G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory Model F2-8500CL5D-4GBPK
VGA: EVGA 896-P3-1255-AR GeForce GTX 260 Core 216 896MB 448-bit GDDR3 PCI Express 2.0 x16 HDCP Ready SLI Supported Video Card
HDD: Western Digital Caviar Black WD6401AALS 640GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive
as far as i can tell i have an amd 780g chipset (intergrated with the motherboard ,the hd3200 package)
The problem im having is my pc wont recognize my sata ide controller and uses "Standard Dual Channel PCI IDE Controller"
Can anyone point me in the direction for the drivers?
Cpu i5 or AMD 1090t or whatever. I can pick out a motherboard that will support USB3 and SATA3 and of course I will have the 2 HD for them. I don't know crap about motherboards but when I pick one out to build my new computer what should I be looking at bus speed and so forth because I don't want to pick out a motherboard that will support them but is slow as mud so why bother so I want to do this right and another hundred here or there don't matter but I don't need a dragster just a Corvet. what I might want to take a hard look at on a motherboard?
View 5 Replies View RelatedI have a Panasonic Toughbook CF-30 MK3. Myself and many others are trying to figure out why we can't get SATA II speeds. There is nothing in the BIOS that helps, nor the manual. The only thing that the BIOS says in the System Info is SATA-AHCI. I have tried several different SSD's and they all max out at around 130Gbps. Someone mentioned that it might not support S-II, but I have a very hard time believing that with the computer only being 2 years old.
View 2 Replies View RelatedI want to add another HD to my PC but all my sata ports are used up, the only other option would be to buy an IDE to SATA converter.
If I buy a converter will the HD behave as if it were using SATA, will the transfer speeds remain the same? Or will it degrade?
Someone told me it would be possible to add 2 devices using the PATA/IDE ports, but so far I've only seen converters that only have an option for 1 IDE device. How many devices can the PATA port support?
what is the difference between the sata 1 and 2?
View 1 Replies View Relatedwhen the computer goes to sleep and then later shuts down, and then when I go to wake it up, it won't boot. The message is Cannot find SATA-0 (Which is the primary boot disc). A physical re-start solves the problem, as it will then boot normally. Is the disc going south? The Check Disk feature says that it is OK.
It is a Dell E520 running Windows 7. It has the latest BIOS upgrade.
i use the USB TO SATA ADABTOR but that dose not work my windows is 7
View 1 Replies View RelatedI need to reinstall my Windows 7 from cracked to legal. My PC has 3 HD in it. 200 GB SATA, 200 GB Primary IDE and 160 GB Secondary IDE. It is currently loaded on the 200gb Primary IDE and the other 2 are for backup and saving data. Would I be better off installing Windows 7 on the SATA drive and using both IDE drives for backup and saving data? If so is the easiest way to just disconnect the IDE drives until Windows 7 is installed then format the original OS drive to use for backup?
View 1 Replies View RelatedI had a new external HDD WD My Book Essential USB 3.0 (2TB) 6 month ago. All was good until two days ago. I rebooted my computer and I won't boot up. After disconnecting WD HDD it work perfectly But after I turned my PC off, and tried to turn it on, again it won't boot up with the HDD connected AND some weird ticking noise started in HDD itself. I sounds like it's trying to boot but failing and trying again. So I disconnected, boot up the system and then plugged it in. Nothing Not in explorer, not in disk management not in Acronis program, nothing.I rebooted and it showed and Local Disk R, but I can't even start disk management or open it with explorer, or even open any program to be able to see/fix it. In the end, HDD wasn't even turning on.So the next day I called tech support of WD. They told me standard stuff, like "Disconnect, Reconnect Try another port, etc ". Nothing. By warranty they can replace it, BUT I don't care about the drive itself, I need data. In this case they can't help me. All they told me is to contact special company for that, and it's gonna cost me up to 1000$.After that call, I noticed a burning smell from HDD. It was connected to power and USB. I disconnected and I opened the case of my HDD. SATA HDD itself seams to be fine, but the connection board (with USB and power) burned.So, I connected directly via SATA to my PC. And that's when the fun starts: BIOS did not recognized it. I switched the SATA port. BIOS showed the model and everything but it gives me "Ultra DMA Mode-5 S.M.A.R.T Capable but Command Failed." Reboot.In different software... NOTHING. Reboot again: and again "Ultra DMA Mode-5 S.M.A.R.T Capable but Command Failed". Reboot. S.M.A.R.T. Command Failed... Reboot 5 times, all good. Started LiveBoot CD by Wondershare. It found my HDD and UNKNOWN. Was trying to recover data from it, program freeze. Reboot again. Was trying to fix mbr with Win 7 Boot Cd, nothing cuz it can't see were to fix mbr. Reboot. Started HDAT2. Nothing. Reboot 10 times, and HDAT2 finally can see my HDD. Before I start any test I shows me read error from UNKNOWN DEVICE. Started "hdat2 most powerful test". Nothing. No errors was found. O_o. Also I try Read MBR with the same HDAT2. Everything 0/0/0/0. So what else I can possibly try?? Oh yeah, when I connected my HDD via SATA, that "boot or not to boot" sound was still there.
View 5 Replies View Related2 hours ago,i wanted to install windows7 on my sata disk ,cause i destroyed my old partition with ubuntu 10.10. So i started to install Windows 7 .However it couldnt be normal.Then i get an error: . A partition on the disk''0''could not be formatted .The error occurred while preparing the partition selected for installation .Fault code: 0x80070057
View 1 Replies View RelatedHaving just bought a new PC i was left with a perfectly good SATA HDD which I intended for use in backups. The drive seemed to work ok until it cane to backing up! The drive was 320gb but when trying to back up it shows as only 47gb (not much good for a full backup).
View 3 Replies View RelatedI purchased this add-on card for my older AMD 2400mhz 1gb ram box. This is the computer with Windows 7 on the 500gb Pata IDE hard Drive. I wanted to add a 1TB Sata drive since the MB does not have sata. The card has 2 sata connections, 4 USB ports, & 1 IDE connection. It just plugs into an empty PCI slot. For some reason Windows 7 does not detect the card & when I try to install the drivers Windows 7 says cannot detect any hardware. The card has VIA VT6421A chipsets.
View 4 Replies View RelatedI want to dual boot Win XP and and Win 7 and I need my SATA drivers. I've been searching the internet and the ASUS website but I can't find the SATA drivers.I have an ASUS G73JH. I can't find my MoBo model. I used everest but it says unknown motherboard. My hard drive is a Seagate Momentus St9500420as.
View 8 Replies View Relatedthe board is DFI lanparty DK P45-T2RS PLUS, i'm trying to install the sata driver, but i have no idea which of the controller i need to update driver for:
View 7 Replies View RelatedDoes any one know how to install sata drivers After XP has been installed?
I have a HP DV6150CA and I have to disable my SATA NATIVE from the bios just to be able to load XP.. But when I dual boot to Win 7 I can use it, disabled or enabled it works either way...
Before I made the commitment to use Windows 7 as my primary OS, I figured I'd experiment in a dual boot environment. My current setup is Windows XP (x32) installed on a 500GB SATA drive. This drive has a partition for the OS and a separate partition for all of my files and data. To install Windows 7 I removed my SATA drive and (successfully) installed Windows 7 (64-bit) onto an 80GB IDE drive (controller 0, disk 0).
After the installation I shut down my system, reconnected my SATA drive, changed the BIOS boot order to look at my IDE and Windows 7 booted without a hitch. My motherboard is a Gigabyte GA-K8U-939
Now, with Windows 7 running and my SATA drive connected, Windows 7 does *not* recognize the drive. It is completely missing from the disk manager. I loaded the drivers for my motherboard ((however since the MoBo is a couple years old, it doesn't have Vista or Windows 7 drivers)), it loaded quasi-successfully but spat out some error about it not being totally successful. Now, after I log into Windows 7 I receive an error that goes like,
Code: Initial ALiRAID error!!Please Check:
1) ALiRAID driver is installed
2) ALiRAID controller is connected to disk drive(s)
When I reboot my computer and switch the boot order in the BIOS to boot from my IDE drive, my system will boot into Windows XP without any problem at all. I've also switched the BIOS setting from "RAID" to "IDE" for the SATA drive and that appears to have done nothing towards Windows 7 being able to access it.
There's gotta be some way to get Windows 7 to see my SATA drive, doesn't there?
In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.
If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.
Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.
I have installed windows 7 ultimate x64 and i am really impressed by it.
but i have a question for you, i have a second 500 gb sata hard drive which i have connected after the install which is formatted with ntfs file system from my original windows xp o/s , it shows up in device manager but will not work , windows ask me to format the drive which i dont want to do because has loads of files on which i dont want to lose.
am i missing something they both use the ntfs file system .
