when googled it says something about the sata drive settings needing to be changed in the bios chang the setting for the sata operation from Raid auto/achi to raid auto ata but in the bios of the hp g61 there is no option for that, i verified this will work for the error because i just restored a dell vostro with a sata drive and it did work, now i just need to get this hp to work it has insydeH20 bios setup utility,
I'm trying to install from a sata dvd drive onto an ide hard disc. I have the raid drivers for my board, x64 vista drivers to be exact.
During the install sequence I obviously get to the bit that asks me to insert a driver disc for the dvd drive. Currently the drivers are on a floppy, so insert the floppy disc and browse to the drivers. windows 7 then starts to load the drivers them fails with a message stating it can't find find drivers for this drive.
Has anyone else tried installing from a sata drive, and if so how did you get on?
i am not sure it's windwos 7 problem or my configurations
i tried to install windows 7 RC on the below setup (all new), but failed
1. SATA harddisk, WD Cavier 1T
2. mobo, Gigebyte GA-GM-785-S2H
3. SATA optical drive. LG-GGC...
the last two components work fine if i replace the SATA HD to a IDE HD, meaning the existing system (xp) started normally. no windows 7 installation
but, when i try the 3 componenets togehter to install windows 7 (the SATA HD was not even formated). the scenarios were:
1. if i configured the cmos to see the SATA HD as AHIC mode, the system would freeze at "verifying DMI pool", not even bothering to start the windows 7 installation disk (even i defined only one start-up device, my optical sata).
2, if i configured the cmos to see the SATA HD as Native IDE mode, the system would go to the optical sata and found windows 7. THE PROBLEM came during "windows is loading files". after like half min, the error message popped out, saying an I/O error occured, either i had a external usb drive corrupted or a storage fault.
The problem came out when i had no usb devices attached at all. then i also tried to copy SATA mobo driver to a usb stick and connected to the system. but still the same problem.
i also tried clear cmos, load default profie,
My questions:
1, how to solve this....
2, should i set native IDE mode before installing windows 7(also other windows systems?)
3, what is at least the correct way to install this.
4, is this a windows 7 installation issue or what?
i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
I've just finished building my new computer and I'm getting BSOD errors when first formatting a hard drive and secondly (after a successful format) installing a game on it.My boot up SSD drive seems to be fine, it's just my other hard drive.64bit Windows 7 Home premium. Full version I bought a a few days ago. The whole computer is new. If you need any further information, let me no.8GB RAM. Intel Core i5 2500k CPU. Radeon 7850 graphics. 120ish SSD. 1Tb hard drive. Asus P8Z68-V Pro gen3 motherboard.Edit:having just seen a notice, I've updated the post to contain two attachments. Or atleast I think I have
i was using win7 ultimate before and last day i tried to install a new win7 and in wich step that i had to choose a drive to install i sow this message "No drives were found. Click Load Driver to provide a mass storage driver for installation." but in the windows that i was using all of the drives was working.and i installed win vista and no messages like this i sow.
ram:4g video: ati radeon hd 5450 cpu:intel pentium 4 cpu 3.00 ghz 3.01ghz
I was wondering If I have one sata 1 and an new sata 2(or 3) on my PC installed on my PC will cause problems in transfer speeds? My Blue-ray is sata 1 also.Does this mean that all disks will work as sata 1?
Recently I dropped my Acer Aspire 1420-2039 notebook damaging the hard drive.I ordered a new WD Blue WD2500BEVT.Unfortunately the week before I dropped my computer, I installed the Windows 8 Consumer Preview.So I downloaded an .iso file of Windows 7 Home Premium 64 bit, (What was originally installed on the computer when purchased) and downloaded the Windows 7 USB/DVD Download tool to re-install the OS using a USB Flash Drive since my computer does not have an optical disk.hen I get to the install screen, Windows will not let me select the hard drive with error 0x80300001 "Windows is unable to install to the selected location."Usually other forums suggest selecting the proper drivers for the drive, however WD does not have drivers available for download saying it uses windows' default drivers
I want to install win 7 professional x64,i have a Dvd iso...Problem i want to solve is next,i have 1 sata disk ,and 1 ide disk...I want to divide Sata on two partition,c and d,and to install system on c..Next,my Ide disk ,has jumper on cable select,i think it could be the only way that is to pc work properly.Problem is ,when i install win 7 on partition c,next happens ,on My Computer,disk drives are not shown as Sataartitions c: and d: but its mixed somewhat,if i recall,itc c: of sata,and d is given t ide disk... i really want to know is there a solution to have primary sata c: and d: ,and than ide diskProcessorModel : AMD Athlon(tm) 64 X2 Dual Core Processor 4600+Speed : 2.57GHzCores per Processor : 2 Unit(s)Threads per Core : 1 Unit(s)Type : Dual-CoreIntegrated Data Cache : 2x 64kB, Synchronous, Write-Back, 2-way, Exclusive, 64 byte line sizeL2 Cache : 2x 512kB, ECC, Synchronous, Write-Back, 16-way, Exclusive, 64 byte line size[CODE]
I have Win 7 x86 Enterprise through the company I work with. I was in charge of beta testing it on partition in the SATA raid array on our SunFire v20z server. It installs like it would on any other computer, does not hang up, and reboots to finish install. when it boots however, it shows win7 boot screen, then goes blank, then restarts computer. when i boot into safe mode it hangs on disk.sys and then BSODs. can someone please tell me what is going on?? I have invested over 2 weeks of work into setting it up.
I have tried numerous times on my PC to install Windows 7 onto my Sata Drive to no avail. Yet as soon as I plug in my IDE HD it installs fine.I have unplugged all external peripherals USB and internal Card Reader. Set my Bios ok as it sees both the Hard Drive and DVD fine (Both in the bios and during selection of hard drive during windows 7 installation). Yet when I come to install it, it craps out at a random percentage saying cannot read from source or worse yet it crawls so slow through the percentages (I really don't think Windows 7 should take 6 hours to get to 15%!!) Yet both the hard drive and dvd are fine and the disc works great on my other PC without the sata drive in.
My motherboard is a Biostar G31-M7 TE with latest bios now what is odd is that I recently updated the BIOS to the latest one so does my problem come from here or was it always going to be a problem on this board? Also when I do have Windows 7 installed on the IDE drive when I plug in ther sata drive inside the whole system goes belly up (from freezes when transferring large files to just not seeing the drive)
I need to reinstall my Windows 7 from cracked to legal. My PC has 3 HD in it. 200 GB SATA, 200 GB Primary IDE and 160 GB Secondary IDE. It is currently loaded on the 200gb Primary IDE and the other 2 are for backup and saving data. Would I be better off installing Windows 7 on the SATA drive and using both IDE drives for backup and saving data? If so is the easiest way to just disconnect the IDE drives until Windows 7 is installed then format the original OS drive to use for backup?
that the system doesn't recognize the Sata HDD on which Windows 7 is installed. I first thought the the HDD was done, because the system recovery couldn't be started and every action was followed with "disk read error". The next step I took was booting with Ubuntu live and there was the surprise, Ubuntu recognized the HDD and all the folders were there, so it seems the problem is not with the HDD but with the OS. What next step should I take
I have built a new system with a 60GB SSD to install the OS on and a 2TB hard drive for everything else. The 2TB drive can be seen in the BIOS but cant be accessed from windows.
I have a custom built HTPC with a Seagate SATA drive. Media Center halted, and Win7 would not reboot. When I attempt to reinstall Win7 it cannot find the drive (C) - "No drive were found. Click Load Driver to provide a mass storage driver for installation."
My research tells me SATA drives don't have drivers. I've changed BIOS SATA drivers from "Enhanced" to "Compatible" with no effect. Don't know what to try next.
Have XP on C drive and looking to install Win 7 on 2nd Sata drive for dual boot. However, when installing a 2nd Sata drive my XP bios identifies it correctly as a Sata drive but my PC Disk management recognises it as a Removeable disk preventing me from installing Win 7. I have tried a couple of different Sata disks with the same result.
I am running Windows 7 Pro. Have a external dual dock connected to a estata port. One of the drives assigned letter K often comes up as E and I have to change as application is looking for K. Another disk in this dock works fine. No problems. why this might be happening or anyway to prevent? Seems like when I go to disk management and assign K it should stay that way.
I've recently purchased two 30GB SSDs which I have set up in a RAID 0 array and I have installed Windows onto these drives. I have a second, 2TB Seagate Barracuda Green HDD that I have used to put my user profiles and additional programs/games on as it wouldn't fit on the SSD.Everything was fine for a few days after installation. Then this morning I rebooted the computer and it just stalled on the flashing cursor (underscore) in the top left corner of the screen. I did the basic fixes (Windows repair, checking RAM) and nothing worked.Then I thought that I should try disconnecting all but the SSD with the OS on it. SUCCESS! It booted to Windows but couldn't find any programs/user data so it created a new "profile". I shutdown the computer and tried reconnecting just the data hard drive.I have two additional hard drives (used for backups) that don't affect anything at all when I plug them in.Does anybody know what could be the problem? I'm at a loss and I need the computer
I recently bought a mobo and gfx card from a friend therefore decided to treat myself and bought a 1TB Hitachi SATA HDD.
As i had a dodgy DVD RW before i installed Windows 7 from my current PATA HD as a custom Installation onto the new Drive after assigning it in Disk manager, formatted and began installation.
All installed fine booted up and asked me which windows to use. selected the new OS and all good, but then, I removed the old PATA drive assuming there would be a Boot block on the new drive allowing boot up with the fresh windows installation and all i got was No boot disc found, please.. bla de bla... so i checked all BIOS settings to make sure all boot sequences were in the right order.. which they were..
I then resorted to put the old PATA HD back in and as soon as i hit the power button there was a spark from the PATA HD i'd just wired back up... Nothing for it to short on as it was laying flat on top of my case. now this wont boot either and im just getting the same message as before whatever i do.
I thought maybe this had blown the IDE slots on the motherboard, so i put my old mobo in and all components, i now get the selection for Windows 7 / Windows 7 (PATA) or Older version of windows. but now when i try and boot the fresh installation of Windows 7 on the SATA drive, it gets to the logo startup screen and restarts.
I need to move the sata connection for my drive "D" on the motherboard, however after moving it Windows 7 won't boot.
Gateway LX6820, 8GB Ram Windows 7 HOMEPREMIUM 64 bit Drive "C"- Intel X25V SATA SSD 40GB, has 200MB System Partiton for MBR and the rest is for the OS Drive "D"- WD Raptor SATA 150GB, has User folders, Program Data, and Programs installed
I have a fresh install of Windows 7 HOMEPREMIUM 64 bit that was done with drive "D" in one of the hotswap bays. All my tweaks, and settings changes are done and Windows operates with no problems. Now I wan't to move the drive to an internal bay. The set up and install was done using sata 4 on the motherboard but due to cable routing I need to use sata 2 for the move.
After the physical move and cable change Windows sees the Raptor as drive "E" not "D", it can't access the user profile and loads a default profile instead. This default profile won't allow access to disk management so I can change the drive letter. I have tried using Diskpart to reassign the drive letters but when I boot into Windows it changes it back to "E" again (must be due to the sata port 2 being assign "E" in an earlier configuration?). I tried using Windows repair but it changes the boot sector to"C", the "C" drive to "D" and the Raptor to "E", had to change the cables to the original locations and do a system restore to fix that one.
I need to move the sata connection for my drive "D" on the motherboard, however after moving it Windows 7 won't boot.
Gateway LX6820, 8GB Ram Windows 7 HOMEPREMIUM 64 bit Drive "C"- Intel X25V SATA SSD 40GB, has 200MB System Partiton for MBR and the rest is for the OS Drive "D"- WD Raptor SATA 150GB, has User folders, Program Data, and Programs installed
I have a fresh install of Windows 7 HOMEPREMIUM 64 bit that was done with drive "D" in one of the hotswap bays. All my tweaks, and settings changes are done and Windows operates with no problems. Now I wan't to move the drive to an internal bay. The set up and install was done using sata 4 on the motherboard but due to cable routing I need to use sata 2 for the move. After the physical move and cable change Windows sees the Raptor as drive "E" not "D", it can't access the user profile and loads a default profile instead. This default profile won't allow access to disk management so I can change the drive letter. I have tried using Diskpart to reassign the drive letters but when I boot into Windows it changes it back to "E" again (must be due to the sata port 2 being assign "E" in an earlier configuration?). I tried using Windows repair but it changes the boot sector to"C", the "C" drive to "D" and the Raptor to "E", had to change the cables to the original locations and do a system restore to fix that one.
Interaction (interface?) between a Sabrent USB 2.0 to SATA/IDE Hard Drive Adapter Product Code: USB-DSC5 and my Windows 7 Home Premium 64-bit?When connected to IDE Drives Maxtor and Western Digital, and through the usage of Windows 7 it tellls me that the Hard Drive "is not ready". Is that a message originated by the Windows 7 software?If so how do I go about "getting the disk ready" so i could change disk type or number or sizes of each partition and/or reformat?unexpected report from the Windows 7 interaction with this adapter and the Hard Drives it holds, 40 GB and 80 GB IDE drives Maxtor and Western Digital. I am trying to use Windows (or some other third party software) to resize the partitions, change the disk type and eventually reformat.
i installed a sata controller because the sata controller on the motherboard went out. I can easily install ubuntu but when i try installing win 7 it asks for a cdrom driver, when i try booting from usb it asks for hdd driver.
Having just bought a new PC i was left with a perfectly good SATA HDD which I intended for use in backups. The drive seemed to work ok until it cane to backing up! The drive was 320gb but when trying to back up it shows as only 47gb (not much good for a full backup).
Before I made the commitment to use Windows 7 as my primary OS, I figured I'd experiment in a dual boot environment. My current setup is Windows XP (x32) installed on a 500GB SATA drive. This drive has a partition for the OS and a separate partition for all of my files and data. To install Windows 7 I removed my SATA drive and (successfully) installed Windows 7 (64-bit) onto an 80GB IDE drive (controller 0, disk 0).
After the installation I shut down my system, reconnected my SATA drive, changed the BIOS boot order to look at my IDE and Windows 7 booted without a hitch. My motherboard is a Gigabyte GA-K8U-939
Now, with Windows 7 running and my SATA drive connected, Windows 7 does *not* recognize the drive. It is completely missing from the disk manager. I loaded the drivers for my motherboard ((however since the MoBo is a couple years old, it doesn't have Vista or Windows 7 drivers)), it loaded quasi-successfully but spat out some error about it not being totally successful. Now, after I log into Windows 7 I receive an error that goes like,
Code: Initial ALiRAID error!!Please Check:
1) ALiRAID driver is installed 2) ALiRAID controller is connected to disk drive(s)
When I reboot my computer and switch the boot order in the BIOS to boot from my IDE drive, my system will boot into Windows XP without any problem at all. I've also switched the BIOS setting from "RAID" to "IDE" for the SATA drive and that appears to have done nothing towards Windows 7 being able to access it.
There's gotta be some way to get Windows 7 to see my SATA drive, doesn't there?
I have installed windows 7 ultimate x64 and i am really impressed by it.
but i have a question for you, i have a second 500 gb sata hard drive which i have connected after the install which is formatted with ntfs file system from my original windows xp o/s , it shows up in device manager but will not work , windows ask me to format the drive which i dont want to do because has loads of files on which i dont want to lose.
am i missing something they both use the ntfs file system .
This seems to be such a frequent issue that it could/should be a FAQ but I haven't found my answer yet.
I am (currently) running Windows 7 64 ULT on my home PC. I purchased an Intel X25M 80GB SATA drive and connected it in order to benefit from the speed. The issue is that setup hangs during the "expanding files" on this drive. Looking back I have *never* been able to install windows (XP Vista or 7) on a SATA drive on my mobo.
In order to avoid confusions I did the following.Removed the 2x400GB striped drives. Removed the old PATA-IDE drive, therefore only drives available were the Optiarc DVD and the new Intel SSD.
