Working on my friends desktop computer and the BIOS doesn't detect the hard drive all the time. If I cold boot or reset the machine the hard drive is not detected. However if I pull the CMOS battery and power cord then drain the capacitors (by pressing the power button) and replug the power the drive is detected by the BIOS and starts booting windows (then freezes). The Computer can boot from CDs fine (from IDE cd drives). When I power up the machine without draining all of it's power/ removing the power cord the BIOS gets stuck detecting the SATA drive. I tried the Hard drive in my machine it and worked fine so I don't think its a drive/cable problem. I also tried one of my known good WD drives in the machine and it doesn't detect it. I have tried replacing the signal cable. Default settings (no options for IDE/AHCI just enable or disable SATA). I'm not sure if windows freezing is a 2nd problem or part of the first.
Motherboard: Gigabyte GA-k9ns Version F9
Drive: seagate 500gb sata (also tried a WD green 500gb & black 1TB)
On my old secondary computer my setup was Motherboard: Chaintech VNF2-350 Master 0: HDS722516VLAT80 with Windows installation Slave 0: WD800BB-53CCB0
But then I started getting Machine Check Exceptions and my motherboard ultimately perished. So I replaced that with a Foxconn K8S755A-6ELRS. But this new motherboard won't detect the hard drive.
It will hang at the part that says "Detecting IDE drives", sometimes it will give up and display "0" where the drive is supposed to be, other times it will hang until you unplug the cable.
If it's on the same channel as the Hitachi drive with XP on it, the BIOS recognizes the other drive, but fails to boot from it. If they are on different channels, it boots the XP drive but will see no hint of the drive on the other channel., even in Disk Management or Device Manager.
I also tried connecting it to my other computer's Intel DP35DP mobo, and it was able to detect/read/write and all that, though it does have a few bad sectors.
My hard drive, a WD Scorpio 200GB, is not being detected in bios. AHCI mode is enabled. When I go into the Advanced BIOS Features, all the master and slave configs are none; however, my SSD is recognized as I am on my computer right now using it. I tried every SATA Port, EVEN THE SATA PORT MY SSD IS INSTALLED ON, and it doesn't work; I tried 2 different cables and still no recognition; I tried 4 different hard drives and still no recognition, so it is not a problem with my motherboard, hard drives, or cables. What should I do? I have been trying to figure this out for 4 hours.
i need to completely remove all from my hard drive so that i can run my restore discs i purchased from gateway- my computer is 6 mos old and came without dics as it had restore capabilities pre installed from factory.
I have had an expensive time with my computer recently but i am now beyond the brink and turning the tide of war to my favour.I have recently kitted my ailing PC out with a new SSD for the OS install.This is working great; i have just tonight had to plug in a brand new GFX card for my gaming pc.(My GFX card burned out due to overheating, so i have now got a new case and proper cooling)Basically, my secondary hard disk (Files Storage etc) is not working, when plugged into my sata port my computer hangs at the Windows Loading screen, also i cannot get into the BIOS.If i unplug the hard drive (Not SSD, 500GB Hitachi) my computer boots in 14 seconds, and the bios works fine.I have concluded my secondary hard disk may be broken.if i can fix it as i can barely afford to buy a new one (even knowing they are cheap).Basically if it had broken i would expect my PC would say so, seems to me that it is just waiting for a response and sitting around for hours to get it
I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.
But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.
I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.
I just installed the RC last night and everything was going okay until I restarted my computer and my backup drive disappeared. It was accessible until I restarted, I didn't install any new drivers.
It's an IDE drive.. it doesn't show up in Disk Management either so I'm kind of stuck at what to do. Any ideas?
hard drive registers in BIOS, but not in the windows 7 Ultimate 64 bit installation screen. Any questions I will answer RIGHT away. Oh dear God please help me. I took it in to a repair shop and I think I knew more than they did and left without any substantive help (but a $40 bill ). Do I need to format the HD? Would drivers help? All the websites say everything should be compatible - no problem - but nothing here.
WD Blue 640 GB (single HDD) AMD Phenom ii GA-MA785GM-US2H Gigabyte motherboard OS: Windows 7 Ultimate 64 bit
recently had a few parts die on me so i have started to rebuild a whole new comp my motherboard is a asrock 970 extreme3 cpu is a fx 8-core black edition and gpu is a gigabyte hd7850 2g gddr5 with a seagate 1tb barricuda 7200 hdd now thats out of the way my problem is im trying to reinstall win7 but neither my bios or win 7 rrecognising my hard drive i get stuck at where it asked me where i want to install it to i try load drive but as i said
My Acer netbook has developed some kind of fault and I am unsure as to what I ought to do. The netbook does boot to BIOS and also will boot up from an external drive...but will not boot normally. I am thinking of replacing the hard drive but don't know if there could be something else wrong. It says sometimes that it can't read it and from this I am not sure if there is something else wrong. If I change the drive does it sound as though things will work? There are also a couple of other intermittent faults such as certain letters and numbers not working and then everything is fine for a while...
I'm currently using a Windows 7 PC built by a friend of mine, but starting yesterday, its been acting up. The problem is there used to be two hard drives I can access, Drive B and Drive C. When I boot up the computer, BIOS only detects Drive C (if I'm not mistaken), and Disk Managements as well. I realized this when all the programs whose targets are on that drive are all broken on the desktop.So Drive B doesn't show up anywhere at all.
Lots of BSOD, lock ups, hard drive not being detected by bios, is it failing? Let me start by saying my PC is custom built, most parts are only a year old. The oldest parts are the harddrive (about 5 years) and the soundcard (about 7 years). I have never had major problems until now (a year after building it).
It all started with a blue screen. KERNEL_DATA_INPAGE_ERROR Reboot windows and it seems to start up fine, gets to the desktop and locks up.
Reboot windows and I get another blue screen. BAD_SYSTEM_CONFIG_INFO
I try to start windows from the last good configuration. Error. Registry file failure. Cannot load hive file. I try booting from the windows cd and running a chkdsk. Hard drive starts making a buzzing sound. It gets to step 3 of 5 and stops. Failed to transfer logged messages. Status 50. Now the bios rarely even "sees" the drive. When I can get it to boot and see it, any attempt at diagnostics and repairs produces errors, locks up, or fails.
Is this a bad hard drive? I would hate to spend the money on a new one only to find it is a bad mobo or virus. How can I diagnose this? If it is a bad drive I would like to save what juice is left in it and try to recover a few files before it dies. Most of the important data has been backed up but I would like to try and get a few game save files if I can. But its not a disaster if the drive data is not recoverable.
I have just installed Windows 7 Home Premium on an HP Pavillion a1629.uk, and the second internal drive is sometimes not present on booting up. The failure rate is about one time in ten. Originally the machine had C: and D: drives with XP installed on C:. The original C: drive was discarded, and a clean installation of Windows 7 was made on on a new 500 GB disk. The original D: 500 GB drive (Seagate ST3500320AS) was left in place, but as stated is sometimes not detected. The drive is always present in the BIOS, before windows boots. On the occasions that it is not detected in Windows 7
So What i am saying is whenever i boot up my computer there is a black with white text screen that says something about an unconfigured hard drive that is in my computer. But then again whenever i am on my desktop doing whatever i can use it perfectly fine. Also it does not show up in the bios. it just has my boot up drive and my optical drive.
I have a hard drive I want to backup to a 64gb flash drive and then restore it to another different hard drive than where it came from. I have windows 7 and office on my laptop and I want it on my desktop pc. There isn't close to 64gb of info on my laptop so it should be fine even though the hard drive says I have 160gb. It is all free space except for those programs.
So, I have a i7 2600K system with a solid state disk as the boot drive, and an older (c2008) Samsung Spinpoint F3 500GB drive as the data drive for programs (that I deem as not worthy of the quick load times). The hard drive has given me some errors over time, and I bought a hard disk to replace it (a Hitachi 1TB). The issue I'm having is that the fact that Windows 7 puts a small (100MB) partition on the F3, and for some reason, even though I'm running Acronis 2012, it doesn't seem to be able to clone the F3 over to the Hitachi. I've also tried Drive XML, and for my 2 hour wait, I only managed to acquire a boot error. Thankfully, I've not done anything rash to destroy the data on the F3, but given the fact that I've seen corrupted files in Steam from that drive, I'm not will to trust it long term with my data. I really need to get the data onto that Hitachi, though... Anyone have any advice for upgrading the HDD in a SSD/HDD system? I don't really feel like it should be so hard, especially if I've bought Acronis True Image, but maybe they haven't designed their product to handle this scenario quite yet?
I have a HP Touchsmart IQ500. Turning my computer PC on today, all I got was a blue HP invent screen with setup, boot menu, system recovery, and system diagnosis, and I could not get past it. I entered the BIOS and figured out that the hard drive was listed as "not installed." Pretty sure that is the main problem.I tried a system restore (with the Windows 7 install disc), but I guess the computer couldn't read the hard drive enough to enter safe mode (I tried restarting and F8ing several times). I put in an external hard drive, and the BIOS read it; however, windows does not allow you to partition an OS on a hard drive.
I have an internal hard disk not in use ,and I would like to make it as external disk !I looked on the net and I found I should have the " encelsure " butt I think I wont find it here in my city .So is there another way ? like usb -esata cable
Me and my brother built me a new computer from scratch (he did the building - i did the watching). I purchased an internal hard drive from Overclockers UK. It's a Samsung 1TB drive. I also have a 64 Solid-state drive in there as my primary hard drive that Windows was installed on and a couple of programs are installed on. My storage disk (the 1TB disk) is for all my music/films etc. Whenever I drag and drop a file into the Samsung hard-drive - it copies it rather than moves it instantly.When I had a laptop, I had 3 external hard drives and this is the way it copied files onto them.how I can get the internal drive to stop acting like an external drive?
I have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?
I have a USB Webcam 6.1.7601.17514 from Microsoft installed on a Fujitsu Laptop (Windows 7 ) and I want to copy and install it on another Fujitsu laptop (Windows 7).The other laptop the camera is not working and there is no webcam driver installed.
I have Windows 7 Ultimate installed on a Dell Optiplex GX620 P4 hyperthread, approx 6 years old. Bios is most current Phoenix ROM Bios Plus 1.10 A11. I have 2 sata drives and 2 IDE drives installed. Boot is from SATA 0. SATA drives 2&3 are not present. All is well with this part of the equation.I had been running a Seagate 250GB IDE drive (ST3250824A) as BIOS drive 4, master drive, jumper selected. I just installed a second 120gb Seagate IDE (ST3120026A) as a slave, BIOS drive 5. That was when things got interesting. When I rebooted BIOS took a long time to load, and then reported that neither IDE drive was present. I then did all the obvious things: Disconnected one drive at a time - BIOS would recognize the connected drive. Switched master & slave drive positions. Changed jumpering from master/slave to cable select. Installed a new ribbon cable. Checked that BIOS drive recognition was set to 'Auto' for both drives. Results are always the same: either drive is recognized when only one is connected but BIOS does not recognize them when both are installed. On boot I receive a warning that IDE Drives 4 & 5 are not present and have to press F1 to continue. When I enter Setup BIOS reports the drives as unknown drive type. When only one is connected BIOS accurately reports the drive model # & capacity.After going through all this,I decided to bring WIn 7 up and see what would happen. To my surprise, Windows 7 showed both drives and worked fine. Device Manager properly reported drive model & capacity. I have used the system in this configuration for several days and everything has worked fine.This is not a problem, per se, since other than slow booting and having to press F1 every time I boot to bypass the BIOS "error" notice the system works fine but I am curious if anyone else has had this problem, and if they found a solution. I have considered forcing a reinstall of the BIOS but since it isn't really broken I don't want to try to fix it and make things worse. I googled this problem before coming here and could not find anyone with an identical situation on any tech site. Can I be the only one who's ever had this happen?
I have a compaq CQ60 104TU laptop, my previous harddrive crashed and i has an external 500GB hardrive lying around. So, I opened it up and took the Harddrive out and inserted into my laptop.When I am trying to load windows into it I get the errorWindows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menuThe Hard disk has no data, and i don't have a CD-Rom, have made my USB bootable manually using DISKPART (this method of installation has worked for me before)[CODE]
I have two 250gb drives that are connected to my one Eide connection on my Asus P5Q deluxe Mobo. They show in the bios and on startup, but not in my computer or drive manager? How can I get them to show up so I can format and use them as extra space.
in the past i had a seperate personal hd for my work laptop I would take my work HD out then install my personal drive in and it worked great. But now on new laptop there is a biosandhard drive can I still switch hard drives or will it not work or will my work know I swap. Them.
make a dualboot comp by adding windows XP to a new partition. I created the new partition with 20gb. (From the 500 of my actual harddrive)But before I actually installed on that, I got distracted with a second harddrive that my dad got(for no reason). It had a full copy of Windows XP backed up on it from another computer, so I figured I would just use that for the dualboot. I plugged it in (wired the same way as my old harddrive, but different data slot), restarted, checked the harddrive in explorer - all the data was there / reading correctly / etc, and I used 'easyBCD' to add the new harddrive to the boot list.(Which, of course, crashes if I try to start it. I just wanted to see what it would do). For a reason I can't remember, I unplugged the second harddrive for a bit, started the computer on accident (I don't know if anything loaded before I shut it off), and then when I plugged it back in.Windows 7 would not launch. It goes to a DOS-like window, except it's just a flashing _ and it never does anything even after a few minutes. XP didn't work still.. so I decided to reinstall XP (as I couldn't tell which harddrive was which on the list, I unplugged the main harddrive while installing onto the new).. and when I did this.. it formatted and installed fully... then restarted.. then restarted.. and restarted.. and just kept restarting, never showing any thing past the manufacturer logo/BIOS load-button-message-thing. So, I then try to use my 3-disk Windows7Recovery disk(burned myself with a program apparently included by the manufacturer.) It installed fully, appearing to work.. but when I launched it, it said "Invalid Partition Table" and wouldn't boot past that. When I insert my driver installer disk, it gives me a basic DOS window thing. dir A: shows the files in the disk. dir B: for some reason shows the same. C: says "Error reading from drive C: DOS area: general failure". All other letter:'s just say "invalid drive". (I'm doing this with both harddrives in.) I attempted connecting the harddrives to an old computer, but it gave an error for both. (It detected the harddrives, but said it had an error reading from it. Windows Explorer asked me to format it... {i'm willing to format one of the drives if anybody thinks it will help, but the old harddrive has data I'd prefer not to lose.} ) Looking on google, I saw several problems that all have similar problems (less overdescripptive than I am though) but none of the fixes suggested worked for me. Also - as I have two different with different errors, I only need to make one of them work.)Also - my other available computer has a CD burner / floppy drive if either are required. I also have several USB's. The computer can boot from USB's and CD's (tested), and I could easily take the floppy thingy and connect it to the computer.also - this computer is probably still under warranty unless unscrewing the hard drive voids it. .. does that count as modification of the computer?
my pc was working fine last night, switched off before bed as usual, woke up this morning, switched on and the machine would not boot up to windows from post. i accessed bios but my cd/dvd drive does not show up there, my hdd does but it will still not boot from startup :/ this message is displayed on the right hand side of boot section of bios 'A device enclosed in the parenthesis has been disabled in the corresponding type menu'. my hdd is listed in brackets, which from what i have discovered so far is not meant to be the case, lol..im not very pc literate so i'm beginning to pull my hair out over this..i can get into windows but i have to go into bios, then exit it and it boots up that way, altho it seems to boot up a lot slower. i cant for the life of me get my cd/dvd drive to show up or even work,it does however have power etc, it just doesn't register on the pc so no hope of me doing a full reinstall at mo either :/ any help with this would be much appreciated as im slowly going insane, lol last thing the pc did before shut down last night was a windows defender update, i tried restore but hasn't changed a thing
I am running Windows 7 Ultimate on HP Pavilion DV2000 laptop.I found that some DVD's won't play on the machine. In My Computer folder, the F: drive does not change even if I insert a DVD. There is no issue about playing CDs and some DVDs. I found that the DVDs which refuse to get detected are mostly commercial DVDs.Is it an issue about DVD region?The drive is 'hl-dt-st dvdram gsa-t20l ata' and it was by default coded to Region 2 (though I live in Region 5 - India). I tried to change the region but I was not successful. I then installed region killer and now the default region is region 5. However, even this has failed to detect the DVD.
I just did a clean install of 7 Ultimate 64 bit using an upgrade disk on my Dell Inspiron 1545. I had been running XP 32 bit service pack 3. Everything is working fine, except my cd/dvd burner does not appear in devices in the 7 interface, and neither does it appear in BIOS. I may have made a mistake by not using windows easytransfer--I selected the files I wanted to bring over manually with a flash drive. It have power and will open and close fine, if a little slowly but it might be my imagination.
I installed 7 with two monitors hooked up and turned on and it detected both of them just fine. But after the install when I boot to windows if both monitors aren't "on" when I boot it won't detect the second monitor when I turn it on. I have to boot with both monitors on for it to detect both of them.
I just want to see if anyone else has experienced this same problem?
