EIDE Hard Drives Connected And Show In BIOS But Not In Disk Manger
Nov 12, 2012
I have two 250gb drives that are connected to my one Eide connection on my Asus P5Q deluxe Mobo. They show in the bios and on startup, but not in my computer or drive manager? How can I get them to show up so I can format and use them as extra space.
View 3 Replies
ADVERTISEMENT
Sep 13, 2012
I have a brand new Sony SVT13112FXS - hard drive is a hybrid of 500 GB HDD and 32 GB SDD.I was attempting to reformat it to get all of the anti-virus stuff off, except when I tried to reformat no disks were shown in the reformat tool. It asked for drivers, so I assumed I'd need to install the SATA/chipset drivers. I downloaded them from the Sony website but it wouldn't allow me to install them (from a flash drive). Specifically the error is "No drives were found. Click load driver to provide a mass storage driver for installation."In my troubleshooting I (stupidly) marked the wrong partition as active and got the dreaded "bootmgr is missing" upon restart. I attempted to repair using the windows 7 disk as a recovery tool and selected "startup repair" 3 times, but it still does not work.I am able to get into command prompt and I am assuming I can inactivate the (wrong) active partition there. However, when I go into DISKPART and type "list disk", all that shows up is my flash drive that I am attempting to install windows from - the computers hard drive does NOT show up here.I will also happily completely reformat instead of repairing, but I cannot do that since I can't get the disks to show up in the reformat tool.
View 7 Replies
View Related
Oct 14, 2011
just completed a first-time new Windows 7 PC build. Successful installation of Windows 7 Pro on WD 600GB 10000 system drive. Went back and installed 4 additional HDD. (2) WD Caviar Black 1TB 7200 RPM and (2) WD Caviar 7200 500GB HDD from XP system that were used for storage.
BIOS sees all HDDs, but are not viewable in Disk Management.
System Specs:
Antec Nine Hundred
ASUS P6X58D-E MOBO
[Code].....
However, only three are visible in Disk Management. Missing (1) WD 500GB (previously used on WinXP system) and (1) new WD 1T.
View 2 Replies
View Related
Nov 13, 2012
I recently noticed an issue when trying to connect to external hard drives. Initially noted that it wasn't showing in 'my computer' and so assumed I had driver issues and sought to update them from Dell's site. After doing so there was still no change, but noted that It was appearing in 'device manager'.I even tried updating the USB hubs from the Device Manager, and it states that they are all up-to-date with the correct drivers. Both external hard drives that i have tried has worked on other PC's so i assume that mine is the issue.
View 1 Replies
View Related
Mar 30, 2011
Does disk manger only shrinks a drive to so much? I have a 1tb. I want to shrink the c partition down to 200 or 300 gb. Disk manger will only shrink the drive down to 550gb.
View 6 Replies
View Related
Aug 8, 2012
in the past i had a seperate personal hd for my work laptop I would take my work HD out then install my personal drive in and it worked great. But now on new laptop there is a biosandhard drive can I still switch hard drives or will it not work or will my work know I swap. Them.
View 2 Replies
View Related
Oct 17, 2009
Background:-
System Gigabyte X48T, 4G ram, usual bits. Video
Sata Port 0&1 - Gigaraid 2x 750G Raid 0 - Scsii disk Boot.
Sata ports 2&3, 4&5, 6, - 5x 500G 2TB dynamic GPT Raid 5
Sata Port 7 -1x 750G Roms & software disk.
Rocket Raid Scsii 0_1, 5x1TB in raid 5.
Scsii 0_0, 1x500G JBOD.
Problem is here.
I have been trying to get this system ready to do extensive HD video editing and multimedia work so thumbnails are critical to sorting out 1000's of clips. Vista just doesnt show thumbnails. I have been waiting years for Windows 7.
This system is fast. Boot drive reads at over 160MB/s sec. The 2 Raid 5 arrays can copy to each other at 250MB/s plus (for multi GB files). Interesting HDTach 3.0.1 only shows 160MB's for the Highpoint array.
They will have to fix their software..
In the last few weeks the system had become very flakey - Windows 7 x64 & vista x64 system -video thumbnail display & codec errors etc, windows explorer hangs, system corruption, bad software & codecs.
The boot manager from the latest (Paragon i think) partition manager for windows 7 got stuck on resize partition and it doesnt time out. I want my pc to be always on for remote access..
Anyway the system finally crashed. I lost one of the Raid0 boot disk array IDs when I tried to delete the boot manager. One disk offline and array gone. 60 hours, 400G of newly imported video from 8mm tapes..
So I decided on clean install just windows 7 after I recovered the data on the raid array.
To that end I removed all the other disks, took a single clean disk and installed vista on it.
Then I went to Bios and deleted the GigaRaid array and recreated it with the original 2 disks.
Changed the boot order in Bios to the first Sata.
Back into windows, initialise the GigaRaid array in windows disk management -Do not partition or format it. Load GetBackDataNTFS and
scan and copy all of the data back to the spare space on the new boot disk.
When I was totally happy I had everything back I loaded Windows Disk management and partitioned the GigaRaid into 250G and 1200G. Formatted the only the 1200G and copied on all of the drivers..
I then shutdown and removed the Vista hard disk and restarted with the Windows 7 DVD. Loaded the Gigaraid drivers and proceded to install Windows 7.
On first reboot, error 80xxxx .
Back to setup and disk management. Delete the new 250G partition and let Install do its stuff. So it creates a 100MB "system" as the first partition then 260G for the C drive and installs itself.
Whoo hoooo! it works.
I shutdown and add the GPT array and the single Roms drive.
Into Bios to set the boot to the Scsii Gigaraid & restart and the dynamic array and Roms disk is there.
Shutdown and install the RocketRaid Card with its 5 disks attached.
Back to bios to set Boot to Scsii Gigaraid.
It always puts Sata 0 first.
Or Scsii 0_1 (the RocketRaid).
Boot back into windows and everything is where it should be.
Clean and fast too. Install all of the software I need.
Now I have a nice system. Time to copy the video I recovered onto the Raid5 array.
So I plug the sata cable into the disk and go into the Highpoint management to scan the disk. Come up ok and is visible in windows.
I copy the data over to the raid.
The I decide to see it the computer will reboot back into windows unattended.. Nope! Screen fills with rubbish that looks like Linux. Says changing boot disk, then stops.
I go back into Bios and reset the boot disk back to Scsii 1_0 (GigaRaid)
Reboot and press F12 for the boot menu. Select the last item - GigaRaid.
Boots back into that Linux looking system (says debian).
I disconnect RocketRaid disk 6, Scsii 0_1 and back to bios and set to Scscii 1_0, Gigaraid, reboot back into windows..
Plug the Rocketraid Scsii 1_0 and reboot - back into Linux?
Question is..
1 What is the purpose of the 100MB that windows installed onto the boot disk.
2 how do i find the boot manager that screws the system when I connect a new drive (including USB key).
3 How do I force the boot to the correct disk array regardless of which drives are installed or not.
4. Is there a boot "something" I can install on every disk to point to Scsii Gigaraid
View 3 Replies
View Related
Oct 22, 2011
winrar installed to get my files in hard drive. I can see the files in winrar but not in windows explorer. how to get this in windows explorer
View 3 Replies
View Related
Dec 21, 2012
I would like to connect my 2.5" external USB hard drive permanently to store my files. However, it seems like my USB hard disk doesn't show up every time I reboot my windows 7. I will need to unplug the usb and then replug it back it for it to be detected, which is a bit of a hassle.
View 4 Replies
View Related
Jun 23, 2011
i am trying to connect my internal harddrive for my dead laptop via a usb port of a working one, but i get the message that the device is not recognized
View 1 Replies
View Related
Jul 14, 2012
my windows does not show contents of my hard disk but linux mint do.i doubt if there is any presence of virus and i deleted all .ini files.(unwanted files).and it does not contain any softwares or any executable files. it contain only media,and pdf files.
View 4 Replies
View Related
Oct 22, 2011
how put password for "MyComputer"
View 2 Replies
View Related
Oct 1, 2011
My external hard disk up until a few weeks ago had been working perfectly. The next time I used it - windows 7 will not recognise it. I have tried different USB ports and computers. But it doesn't seem to work. It doesn't show up in device manager or disk manager. Its like nothing is plugged in. I tried switching hard disk cases and power supplies. But still nothing. The hard disk seems to try and run every so often, the light flashed red and it makes whirring noises as if it was connecting to the computer.
I dont know what else to do ? And it has almos 1500 GB of data.
View 1 Replies
View Related
May 8, 2009
how to change icons for dvd drives? hard disk drives? I used to do that with Tune Up Utilities under Vista but it doesn't work on Windows 7...
View 5 Replies
View Related
Jun 4, 2009
i installed windows 7 and i don't know what i did wrong, but this is what i end up with
C: 1.66 GB free of 9.44 , where as i have total of 80 GB hard drive. and then i have drive "E" which has 64 GB hard drive.
so how can i merge this two drive?
View 2 Replies
View Related
Feb 20, 2012
Set up did not find any hard disk drives during installation?
View 1 Replies
View Related
Aug 27, 2011
I'm currently using a Windows 7 PC built by a friend of mine, but starting yesterday, its been acting up. The problem is there used to be two hard drives I can access, Drive B and Drive C. When I boot up the computer, BIOS only detects Drive C (if I'm not mistaken), and Disk Managements as well. I realized this when all the programs whose targets are on that drive are all broken on the desktop.So Drive B doesn't show up anywhere at all.
View 29 Replies
View Related
Jul 23, 2012
I don't know what is my problem because is not the first time that usb external hard drive is working fine until get damage and said " it need to be formatted " and lost all the INFO because I have to format again the disk to be usefull. Also it is not the same hard disk.
View 1 Replies
View Related
Jun 11, 2010
I have completely formatted my hard disk with seagate seatool. Then I have installed windows xp sp3. I have made 4 partitions at that time i.e. c,d,e,f. After that I have installed windows 7 now I can't see my hdd in disk management or in device manager. Both device manager & disk management are showing me my external drives like pen drive.
View 9 Replies
View Related
Aug 23, 2012
I have a compaq CQ60 104TU laptop, my previous harddrive crashed and i has an external 500GB hardrive lying around. So, I opened it up and took the Harddrive out and inserted into my laptop.When I am trying to load windows into it I get the errorWindows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menuThe Hard disk has no data, and i don't have a CD-Rom, have made my USB bootable manually using DISKPART (this method of installation has worked for me before)[CODE]
View 1 Replies
View Related
Sep 8, 2011
i have brand a new Gateway NV50A with Windows 7 Professional 64 bit. I tried to partition the C Drive with 450GB to make another partition using Spotmau 2009. It displayed a window --that the system needs to restart for partioning. So I clicked on yes. After that it tried to restart and just stops on a blank Spotmau screen doing nothing(Spotmau Powersuite 2009 --Is a computer software used for partitioning and cloning). I tried to restart and bypass this window and start windows. But it doesn't work. I don't want to lose any data. I don't have a Windows 7 Installation CD.
View 8 Replies
View Related
Jun 21, 2010
I am running windows 7 home 64 bit (build 7600). I have a gateway fx7026. It has two internal hard drives. When I look under device manager they are both listed and they are both listed under the bios menu. When I look in my computer though under hard disk drives it only shows the one that I have the OS on. When I had Vista it showed both of them. Is this something I should be worried about. The drives are listed as WDC WD3200AAJS-22B4A0 DRIVE 1 and WDC WD3200AAJS-22B4A0 DRIVE 0.
View 7 Replies
View Related
Sep 6, 2012
I have a HP Probook 4530swith Windows 7 Home Premium 64 bit. When I turn on the PC the windows does'nt start and give a option of starting windows manually, which does'nt work, and repair windows. Repairing windows with windows 7I then decided to reinstall windows 7, but while installing, on the select disk page, it shows a error saying no drives found.I then performed a Hard Disk Test which resulted in failure saying:Failure ID : UC7WX0-5NB67S-XD6V5G-60TF03
View 2 Replies
View Related
Aug 14, 2011
I use a lot of different usb hard drives in my shop. I have two basic enclosures, a generic one that uses pata drives on a usb 2.0 cable and an Apricon USB SATA 2.0 adapter.Suddenly when I plug in a new drive device manager does see the drive and installs it in device manager. I can see the drive in Disk Management but it has no drive letter assigned, and therefore doesn't show up in Computer. I can easily just assign a letter in Disk Management and the drive immediately becomes usable. However, I would like to get Windows 7 to resume automatically assigning a drive letter.
I have tried a program called USB DriveCleanup. What it appears to have done is remove all installations of prior USB drives and when I plug in a drive that has been in the machine previously it then goes thru the install again. Yet still no drive letter. I think the program is doing what would manually be done by going into safe mode and cleaning out all the entries that build up there that don't appear in normal mode, then removes them. Basically it seems like a shortcut to manually doing it.
I also tried a registry fix that essentially asked me to delete the upper and lower filters. This seems similiar to fix for CD/DVD drives that no longer appear in Computer. This fix also didn't work.I tried removing and reinstalling the chipset drivers. Still no go.Running Windows 7 Pro SP1, H55 chipset.
View 1 Replies
View Related
Sep 19, 2012
I have to harddrives, drive :C/ and drive D :/ drive c has the basic miniums and came with 16 gbs of space which is completely full with windows , then drive d has 136gbs and is 103gb of free space left ANYTHING i try to download i try to make it go to Drive D but none the less i keep getting the error "not enough disk space"
this is a brand new system, that a friend whos good with computers built for me for my gaming needs, i have a intel r core tom 2 quad cpu 6600 @ 2.40GHz 4 gb ram 64 bit operating system..
View 2 Replies
View Related
Aug 14, 2012
trying to install Windows 7 on sony laptop with a copy that is different from the original copy of Windows 7.did partdisk, clean all, create partition, and dvd install gave the "can't install to disk, turn on disk controller in BIOS" error. there is no disk controller function in my BIOS.if partdisk clean all was successful, does that mean the HDD and its controller board are ok, that is, not physically damaged, and the problem is with software/installation/setup etc.?what should i do next, in order to have a successful install?
View 9 Replies
View Related
Jan 17, 2009
i have two external hardrives, well a laptop hardrive and a desktop hardrive in enclosures, and they were working fine with windows 7, but then i installed a virtual disc program virtual clone drive and now they won't show up at all.
anyone else have a similar problem or know what may have happened, i already uninstalled the virtual clone disc program but it still won't load.
View 2 Replies
View Related
Nov 11, 2011
i'm working with a new pc build that uses a 60 gb ssd for its boot drive, and which is also reusing some "old" sata hdds for storage.
at the time i installed windows 7 ult 64, i had only a new ssd plugged in, and the bios was set to ahci mode. the installation went fine and i was able to boot into windows afterwards without issue.
then, i connected a wd caviar black sata hdd to use as storage, with the ssd being the boot drive. with both of them connected, windows will not get past the starting windows screen.
i made this video of the program before i understood that it was a drive controller issue: startup problem - Internet in it, you can see that windows boots fine in ahci mode with just the ssd plugged in, but that when the backup sata drive is also connected it doesn't get past the starting windows screen.
for the record, this caviar black hdd was my previous boot os, and it also has a windows 7 install on it (which i've renamed the base folder of), but it is not booting from that hdd. also, i have tried the same thing with other "old" sata hdds that do not have any previous windows install on them, and the result is the same thing which is shown in the video.
View 9 Replies
View Related
Dec 15, 2011
How do I get my external drives to show up in my computer as a letter and not in the printer and devices.... Some of my external drives works fine. Everything was working fine 3 months ago. Everything works fine on my laptop...
View 1 Replies
View Related
Aug 13, 2009
I just installed the new Windows 7. Until I deconnected my second HDD, a 120 GB IDE does not wanted to install. Now when is installed, I reconnected the second HDD. When turn on the windows, it´s not seen and my second DVD-RW, which is IDE also is not seen.
Also none of those 2 is not seen is the BIOS. At startup it hangs 30-40 seconds, freezing, before displaying BIOS Post message notes.
Before Windows 7 I had Vista and all was working fine.
What can I do? Please, a hint to sove that.
View 1 Replies
View Related
May 30, 2011
am trying to do a backup of my Win 7 system drive (C, but the backup utility is saying that it must backup by non-system drives (E: and H, which happen to have "System Volume Information" folders on them. They are not system drives. E: is my main utilities drive and H: is my games drive.Somehow, Windows thinks they are system drives, when in reality they aren't.Any ideas on how to change them? When I go in to Disk Management, they are not showing as system drives. They are all partitions on the same hard drive, but there are other partitions not included in the backup.
View 3 Replies
View Related