Intel Sata Controler ICH10R AHCI + Jmicron AHCI Error
Jul 16, 2009
I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.
As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.
View 3 Replies
ADVERTISEMENT
Oct 1, 2011
I'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..
View 6 Replies
View Related
Aug 10, 2010
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
View 9 Replies
View Related
Jun 7, 2009
In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.
If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.
Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.
View 4 Replies
View Related
Sep 15, 2009
I would like the good and bad about running your SATA drives in IDE and AHCI modes.
I have 3 drives. 1 SSD and 2 normal hard drives.
Does it even make a difference? I have an Esata bracket that I want to run in AHCI mode but how about the normal system and data drives? What is the best way to set up drives?
View 0 Replies
View Related
May 11, 2011
I'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.
My questions are:
1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?
2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)
3. I intend to run XP mode, will AHCI mode pose any problems for this?
View 2 Replies
View Related
Aug 27, 2012
I have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.
My question:
SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s.
TDK DVD+R disks tested OK (on other PC) for 16X capability.
Why is Nero reporting of only 2.4X and 4X writting speeds?
View 7 Replies
View Related
Sep 28, 2012
I have just fitted a SSD drive in my computer windows 7 64 bit system, when I installed windows onto the new SSD I just unplugged my old hard drive and fitted the SSD and just installed windows 7 and all worked ok. But after the new install was working I was told I needed to make a change in the BIOS to alter the settings from treat Sata as IDE to treat Sata as AHCI. I did this and all was ok with the new drive the installation worked and the new drive is running ok.
But now I have since read that I should have made the bios change before installing windows nad should not be done after the install, So do I need to reinstall windows 7 with the bios changes to treat sata as AHCI before I install or will it work ok it seems to be ok but im not sure now. I was also under the impression that I could still have my old hard drive fitted and just select the hard drive I wanted to boot from as the computer started, I wanted to do this so.
I could still has access to all my old stuff if I needed it. But now my old hard drive will not boot until I change the Bios back to treat Sata as IDE, so is this not going to work or will I have to change the bios each time I need access to my old drive. Also I have an Asus P6T SE motherboard so can I plug the SSD into any Sata port or is it better to plug it into number 1 if so how do I find which one is number one.
View 4 Replies
View Related
Oct 18, 2011
I'm installing Seven on a WinXP machine and completed the install, but forgot to change the SATA setting in the bios from "compatibility mode" to AHCI. Now when I change it, windows gives me bluescreen on boot.I'm dumbfounded that Windows Seven startup repair can't fix a problem this simple, but it completely failed, wasn't even able to find a problem.I was thinking it might be easier to just reformat and begin the install over again, or startup in safemode and install the intel SATA drivers... assuming it will let me boot into safemode with AHCI enabled.ps. On the other computer (different thread), I'm going to wait till I have several hours of uninterrupted time, in case I need to begin over installing all the windows versions one at a time. I'll reply with any success/failure on that thread later in the week.
View 4 Replies
View Related
Jul 13, 2012
I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.
View 1 Replies
View Related
Apr 30, 2011
A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.
View 9 Replies
View Related
Dec 18, 2010
Reinstall w7 Upgrade on new Sata III as c: with AHCI support?
View 9 Replies
View Related
May 17, 2012
i have an m17 r2 alienwAre laptop.in the bios menu the sata option HCAI is selected but when the comp boots it says no operating system is found when booting for bios sata option RAID it runs fine. But the comp should be on HCAI in order to run features that a specific to that computer . I have tryed reformatting but in HCAI it on finds the second of 2 500g hard drives but the partition with the boot is on hdd1 not hdd2 . Boot up again with RAID it finds both and and I can reformat have tryed to reset the registry and have tryed using drivermax to find out if I'm missing sata drivers I've also tryed reinstalling my bios from the dell
View 6 Replies
View Related
Aug 15, 2011
Can you teel me some intel motherboards that support AHCI mode?
View 3 Replies
View Related
Jan 6, 2009
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
View 0 Replies
View Related
Nov 27, 2012
I have recently installed a Crucial M4 256 GB SSD in an Acer Aspire 5742 laptop as a replacement for it's aging HDD. This was followed by a clean install of Windows 7 Home Premium 64 bit on the new drive.
So my next step is to ensure that the system has all of the appropriate and up to date drivers installed. Most of the relevant information I found on the Acer website:
[URL]
I am familiar with most of the device drivers listed here and don't expect to have any trouble tracking down the best versions currently available but I am not sure about the "Intel SATA AHCI" driver in particular. It has been my understanding that to enable TRIM on an SSD dedicated as the system drive you just have to set SATA mode in BIOS to AHCI and windows will take care of the drivers during install of the OS.
So my question is will I see any benefit in installing the latest Intel AHCI driver (ver 11.6.0.1030) over the MS one originally installed with Windows?
Alternatively is it a better idea to leave the configuration as it is (working pretty well) and avoid potential software conflicts?
View 4 Replies
View Related
Mar 30, 2012
I just changed my disk setup from:
1 SATA HDD Primary OS Disk
2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk
1 SATA HDD Backup Disk
[No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID
--> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome
Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
View 8 Replies
View Related
Aug 8, 2011
When i turn my laptop on it comes up with: AHCI port0 device error. At the moment i am trying to re install windows 7 but it (after changing the BIOS) it gets to a screen where it states that it is starting?
View 2 Replies
View Related
Jun 26, 2012
When I start up my pc I my screen stops at the POST screen where down to the bottom it says AHCI Port 0 error...I never had that error before as normally I won't even see the POST screen.
View 14 Replies
View Related
Jun 9, 2011
AHCI Port Error 0 Press F2 to continue. This error shows on my Gateway zx4800 but when I press F2 nothing happens. S.M.A.R.T capable and status BAD.....it also show this above the AHCI error. My hdd works with other PC.
View 2 Replies
View Related
Jun 24, 2009
I was going to install W7, and cant find the Windows 7 driver for the Intel ICH10R for the motherboard GIGABYTE GA-EP45-UD3P LGA 775 Intel P45.
I cant find on Gigabyte site (though they say the motherboard is W7 ready), and not on the Intel site.
Would using the Vista driver, installing with flash drive during installation, work?
View 15 Replies
View Related
Sep 21, 2011
I recently swapped out my motherboard for a Gigabyte GA-970A-UD3. I was trying to overclock my CPU and after a crash and CMOS reset I was no longer able to complete WEI. This was fixed by reinstalling the BIOS firmware but when I ran WEI again, I was now getting a 5.9 score for my SSD (OCZ Agility) when it was previously 7.2.
Now I can no longer get Windows to use the AHCI driver (neither MS nor AMD) for the drive. I am running in AHCI mode but the driver being used for the SSD is a generic "disk drive" (disk.sys and partmgr.sys). When I try to update this driver, it tells me I am using the latest one; it also does not let me manually select the AHCI driver.
After multiple attempts at switching back and forth between IDE and AHCI in the BIOS, uninstalling and reinstalling AMD AHCI drivers, nothing changes. Still the same 5.9 WEI score and generic driver.
View 2 Replies
View Related
Apr 8, 2012
i have an ASUS M5A88-M motherboard, and a Western Digital WD2503ABYX HDD. i am trying to make that drive work in AHCI mode, but when I try, the disk won't boot. i think the HDD is AHCI compatble, tho not certain. i went into the registry to set a value=o for the relevant AHCI parameter, but no luck. if i need a full re-installation of Windows 7 64-bit, does it prompt me along the way to set the mode to IDE or AHCI?.
View 2 Replies
View Related
Aug 8, 2012
I have SSD as primary system drive and 2x512GB HDDs as RAID 1 for storage.In bios i have options to set them as AHCI, IDE and one more that i forgot...
View 9 Replies
View Related
Jun 24, 2010
Is there any real noticable benefit from having a SATA mechanical HDD use AHCI or IDE? Also, if there is any benefit, is it related to the rpm speed that the drive is capable of?I keep reading conflicting reports on this, some say AHCI is best, others say there is no real difference unless the disk is an SSD.I am about to do a clean install of Windows 7 on a laptop 5400rpm mechanical HDD so thought I may as well set the mode before proceeding with the install.
View 2 Replies
View Related
Nov 26, 2012
I recently installed Windows 7 Home Premium on a new blank SATA hard drive which I had formatted using the default settings under Windows XP Disk Management.Prior to installing Windows 7 on this PC, I disconnected my other SATA hard drives to preclude any issues during formatting/installation.What I would like to know is whether changing the BIOS disk access mode from IDE to AHCI will impact my ability to access my old hard drives (once I reconnect them)?
View 6 Replies
View Related
Jan 14, 2013
I recently purchased a HP 8440p laptop with Windows 7 Pro. installed. I dicided to partition the drive and install XP-Sp3 on the newly partitioned drive. Before I could load XP I had to change the configuration to IDE. Once I did that all went fine. Now in order to run betwwen OS's I have to set my configuration AHCI for W7 and IDE for XP.
Is there a better way of doing this beside alway re-configuring the bios for AHCI or IDE?
View 8 Replies
View Related
Sep 13, 2010
Driver update program says new driver available 1.0. Any issues regarding updating this driver. No problems needed. Dell Inspirion laptop Win 7 Home Prem. 64bit 4gb ram
View 7 Replies
View Related
Oct 21, 2009
I have found on 4 different boards if I install in AHCI mode, Windows 7 seems to "find" the drivers for running in AHCI/RAID mode at install. If I install in IDE mode, it does not and I have no option to switch to AHCI/RAID if needed. In the past you had to press F6 (or whatever) and install them from a floppy. I think this is no longer the case with Windows 7. Can anyone confirm this. I don't even have a floppy and never will. I will install in AHCI so I have the choice in the future. Is there any down side to doing this and am I right?
Also - I know there is a registry "hack" you can use to boot into AHCI after installing in IDE but why does everyone not install in AHCI so they have the choice? Am I way off here? Are you planning to install in AHCI to have this benefit?
View 5 Replies
View Related
Aug 7, 2012
Everytime i want to swap hard disk with different OS, WinXp(IDE) to Windows 7(AHCI), i need to do change some hard disk setting on BIOS. Is there any way that i can do to make both hard disk with different OS compatible on the desktop PC without change any setting on BIOS everytime i change hdd? Is there a way to make WinXP IDE mode to run under AHCI mode?
View 1 Replies
View Related
Oct 27, 2009
me as the most of you is using Windows 7 with so much fun! I do have a little problem,don't know why actually,this is why i'm here asking for help. First of all here is my hardware configuration:
Asus P5Q PRO (latest bios,waiting if Asus is ever going to release the EFI also for my motherboard lol just like happened with P5Q Deluxe,anyway).
In bios options if I select AHCI i get faster performance and system responsiveness,but from time to time,it could happen anytime,i get complete hangs up so i have to hard reboot my pc. I tried EVERYTHING,also Intel sata ahci latest driver for my motherboard and nothing works. This happens with both 32 and 64 bit of Windows 7,and it doesn't seem to happen if it's set to IDE (which definitely makes my computer less responsive). Thanks in advance to anyone that will help me
I'm beginning to thing that it's the hardisk getting insane,it's the oldest hardware component in my pc now.
View 5 Replies
View Related
