Does Intel Dg41wv Support Ahci?
Aug 15, 2011Can you teel me some intel motherboards that support AHCI mode?
View 3 Replies
ADVERTISEMENT
Intel Sata Controler ICH10R AHCI + Jmicron AHCI Error
Jul 16, 2009I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.
As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.
Reinstall Windows 7 Upgrade On New Sata III As C: With AHCI Support?
Dec 18, 2010Reinstall w7 Upgrade on new Sata III as c: with AHCI support?
View 9 Replies View RelatedCorrect AHCI Driver Setup For M4 SSD - Intel Or MS?
Nov 27, 2012I have recently installed a Crucial M4 256 GB SSD in an Acer Aspire 5742 laptop as a replacement for it's aging HDD. This was followed by a clean install of Windows 7 Home Premium 64 bit on the new drive.
So my next step is to ensure that the system has all of the appropriate and up to date drivers installed. Most of the relevant information I found on the Acer website:
[URL]
I am familiar with most of the device drivers listed here and don't expect to have any trouble tracking down the best versions currently available but I am not sure about the "Intel SATA AHCI" driver in particular. It has been my understanding that to enable TRIM on an SSD dedicated as the system drive you just have to set SATA mode in BIOS to AHCI and windows will take care of the drivers during install of the OS.
So my question is will I see any benefit in installing the latest Intel AHCI driver (ver 11.​6.​0.​1030) over the MS one originally installed with Windows?
Alternatively is it a better idea to leave the configuration as it is (working pretty well) and avoid potential software conflicts?
Cannot Find Intel 5 Series 4 Port SATA AHCI Controller Drivers For Windows 7
Oct 1, 2011I'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..
View 6 Replies View RelatedDoes Intel T8100 Support 64 Bit ?
Dec 1, 2009I have a Sony PCG 8112L with an Intel Core Duo T8100 processor. Will this processor support 64 bit Windows 7?
View 1 Replies View RelatedIntel 865GBF No Native Support
Feb 9, 2009Installed Win 7 over an old Intel 865GBF main board (Intel Extreme on board graphics controller with shared mem). Getting the graphics drivers to work is so frustrating!!
Everything works fine except:
It installs the standard VGA driver by default -- which doesn't allow my LCD/TV to go full res (1680x1050). Also, no updates for the same.
If I install the Intel drivers from the website, (in XP compatibility mode) they work fine, except keep hanging whenever there is any video playing (WMP / Flash / etc) and generally Windows 7 becomes crashy/hangy. There are no drivers for the 865 mobo from Intel (only support till winXP).
Any ideas?
Does Intel Pentium D 2.8ghz Processor Support X64 ?
May 24, 2009I have an Intel Pentium D 2.8ghz.
Can it support x64 or can it only support x32.
I have tried to find out for myself but my search came up cold, i could not find anything.
Intel 82865g Video Card Support
Oct 22, 2009I use the Dell Computer Gx270 and my graphic card intel 82865g. i installed this driver in windows 7 this driver work properly but this not support to windows dvd maker. when i click on windows dvd maker error is video card is not supported please help me how slove this problem.
View 5 Replies View RelatedList Of Intel Processors That Support XP Mode
May 3, 2009It seems some of the most advanced Intel Processors doesnt support XPMode
for eg: Core 2 Quad Q8200 and Core 2 Duo E7400 wont support XPMode
so here is complete list of Intel Processors(both desktop and Mobile) that support XPMode:
Desktop CPUS
Core 2 Duo
E4300/4400/4500/4600/4700 NO
E6300/6320/6400/6420/6540/6550 YES
E6600/6700/6750/6850 YES
E7200/7300/7400/7500 NO
E8190 NO
E8200/8300/8400/8500/8600 YES
Core 2 Extreme
QX6700/6800/6850 YES
QX9650/9770/9775 YES
X6800 YES
Core 2 Quad
Q6600/6700 YES
Q8200/8200S/8300/8400/8400S NO
Q9300/9400/9400S YES
Q9450/9550/9550S/9650 YES
Core i7/Core i7 Extreme
I7-920/940 YES
I7-965/975 YES
I7-9200/9500/9750 YES
Pentium D/Pentium EE
805/820/830/840 NO
915/925/935/945 NO
920/930/940/950/960 YES
955/965 YES
Pentium for Desktop
E2140/2160/2180/2200/2220 NO
E5200/5300/5400 NO
Mobile CPU products
Core 2 Duo Mobile
L7200/7300/7400/7500 YES
P7350/7450 NO P7370 YES
P8400/8600/8700/9500/9600 YES
SL9300/9400/9600 YES
SP9300/9400/9600 YES
SU9300/9400/9600 YES
T5200/5250/5270/5300/5450/5470 NO
T5500/5600 YES
T5550/5670/5750/5800/5850/5870/5900 NO
T6400/6570 NO
T7100/7200/7250/7300/7400 YES
T7500/7600/7700/7800 YES
T8100/8300 YES
T9300/9400/9500/9550/9600/9800 YES
U7500/U7600 YES
Core 2 Extreme Mobile
QX9300 YES
X7800/7900 YES
X9000/9100 YES
Core 2 Quad Mobile
Q9000 YES
Q9100 NO
Core 2 Solo
SU3300/3500 YES
U2100/2200 YES
Core Duo
L2300/2400/2500 YES
T2050/2250 NO
T2300/2400/2500/2600/2700 YES
T2300E/2350/2450 NO
U2400/2500 YES
Core Solo
T1300/1400 YES
T1350 NO
U1300/1400/1500 YES
Source:
http://processorfinder.intel.com/Default.aspx
Intel to Add support for Intel Virtualization for
Core 2 Quad Q8300,
Core 2 Duo E7500,
Core 2 Duo E7400,
Pentium E5400 and
Pentium E5300.
So the Processor bought after June 12 will support Hardware Virtualization
915 Motherboard Intel Support Chipset Motherboard Sound, Vga, Usb Drivers Download
Dec 18, 2011915 motherboard intel support chipset motherboard sound, vga, usb drivers download
View 1 Replies View RelatedSB600 ATI RAID AHCI Drivers? (BSOD On Boot If In RAID/AHCI Mode.)
Jan 6, 2009anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
Intel Corporation Driver Update For Intel(R) Management Engine Interface?
Oct 9, 2011I bought a new laptop now and I am not so well with the technology it says: Intel Corporation driver update for Intel(R) Management Engine Interface so what do I need to do now?
View 2 Replies View RelatedDisable Intel® Turbo Boost Technology Monitor & Intel® Management Engine Components Or Not?
Jan 25, 2011May I know can I disable Intel® Turbo Boost Technology Monitor & Intel® Management Engine Components or not? If I disable both of them will cause any bad effect?
View 7 Replies View RelatedIntel I7 3770k Or AMD 8350 Or Intel I5 3570k?
Jan 1, 2013See, I have a AM3+ motherboard, and currently a FX 6200 clocked at 4.2GHz, thing is, I feel when I try to play say BF3 on a 32 man server, My pc run's smooth, yet come to a 64 man server, My PC feels sluggish and well fails. Now I know Its going to effect my FPS and CPU usage with what settings in game am I running, well Ultra I don't use I mainly use a mix of medium and high, to Me its all about performance before eye candy, but BF3 seems to have no performance boost the lower I turn the settings down, I mean with one card I get 98-99% usage but in SLI I get 50% on each card with v sync disabled and on ultra I have even tried with settings on low and enabling v sync, lol that is just worse! I have been told the higher the settings, the higher the usage, and my cpu seems to be lagging behind.I know there is things to take into consideration like the Ram, Graphics, Hard drives, Lag ect, But I'm running two GTX 480's, 2 Velociraptor Hdd, 16GB Corsair Dominator Ram, a Corsair HX 1050w psu and Windows 8.Come January I'm planning a upgrade, but what My dilemma is should I move to Intel has I feel my issue is a major bottleneck with the 480's and my CPU, I don't want to buy a 200 cpu (8350) and a few months down the line have to invest in a Intel because the Pile driver has failed like the Bulldozer did! Or just upgrade to a Intel i5 or i7, I mainly game but do video work as well, even considering getting a i7 2600k or 2700k,
View 4 Replies View RelatedCannot Use AHCI Driver For SSD
Sep 21, 2011I recently swapped out my motherboard for a Gigabyte GA-970A-UD3. I was trying to overclock my CPU and after a crash and CMOS reset I was no longer able to complete WEI. This was fixed by reinstalling the BIOS firmware but when I ran WEI again, I was now getting a 5.9 score for my SSD (OCZ Agility) when it was previously 7.2.
Now I can no longer get Windows to use the AHCI driver (neither MS nor AMD) for the drive. I am running in AHCI mode but the driver being used for the SSD is a generic "disk drive" (disk.sys and partmgr.sys). When I try to update this driver, it tells me I am using the latest one; it also does not let me manually select the AHCI driver.
After multiple attempts at switching back and forth between IDE and AHCI in the BIOS, uninstalling and reinstalling AMD AHCI drivers, nothing changes. Still the same 5.9 WEI score and generic driver.
How To Get AHCI And IDE Mode
Apr 8, 2012i have an ASUS M5A88-M motherboard, and a Western Digital WD2503ABYX HDD. i am trying to make that drive work in AHCI mode, but when I try, the disk won't boot. i think the HDD is AHCI compatble, tho not certain. i went into the registry to set a value=o for the relevant AHCI parameter, but no luck. if i need a full re-installation of Windows 7 64-bit, does it prompt me along the way to set the mode to IDE or AHCI?.
View 2 Replies View RelatedHow To Set SSD And HDD In The Bios (AHCI, IDE)
Aug 8, 2012I have SSD as primary system drive and 2x512GB HDDs as RAID 1 for storage.In bios i have options to set them as AHCI, IDE and one more that i forgot...
View 9 Replies View RelatedAHCI Or IDE For Mechanical HDD ?
Jun 24, 2010Is there any real noticable benefit from having a SATA mechanical HDD use AHCI or IDE? Also, if there is any benefit, is it related to the rpm speed that the drive is capable of?I keep reading conflicting reports on this, some say AHCI is best, others say there is no real difference unless the disk is an SSD.I am about to do a clean install of Windows 7 on a laptop 5400rpm mechanical HDD so thought I may as well set the mode before proceeding with the install.
View 2 Replies View RelatedMoving From IDE To AHCI?
Nov 26, 2012I recently installed Windows 7 Home Premium on a new blank SATA hard drive which I had formatted using the default settings under Windows XP Disk Management.Prior to installing Windows 7 on this PC, I disconnected my other SATA hard drives to preclude any issues during formatting/installation.What I would like to know is whether changing the BIOS disk access mode from IDE to AHCI will impact my ability to access my old hard drives (once I reconnect them)?
View 6 Replies View RelatedChanging Between AHCI Or IDE?
Jan 14, 2013I recently purchased a HP 8440p laptop with Windows 7 Pro. installed. I dicided to partition the drive and install XP-Sp3 on the newly partitioned drive. Before I could load XP I had to change the configuration to IDE. Once I did that all went fine. Now in order to run betwwen OS's I have to set my configuration AHCI for W7 and IDE for XP.
Is there a better way of doing this beside alway re-configuring the bios for AHCI or IDE?
AHCI Serial ATA Controller?
Sep 13, 2010Driver update program says new driver available 1.0. Any issues regarding updating this driver. No problems needed. Dell Inspirion laptop Win 7 Home Prem. 64bit 4gb ram
View 7 Replies View RelatedAHCI Drivers At Install
Oct 21, 2009I have found on 4 different boards if I install in AHCI mode, Windows 7 seems to "find" the drivers for running in AHCI/RAID mode at install. If I install in IDE mode, it does not and I have no option to switch to AHCI/RAID if needed. In the past you had to press F6 (or whatever) and install them from a floppy. I think this is no longer the case with Windows 7. Can anyone confirm this. I don't even have a floppy and never will. I will install in AHCI so I have the choice in the future. Is there any down side to doing this and am I right?
Also - I know there is a registry "hack" you can use to boot into AHCI after installing in IDE but why does everyone not install in AHCI so they have the choice? Am I way off here? Are you planning to install in AHCI to have this benefit?
Configure SATA As IDE Or AHCI
Jun 7, 2009In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.
If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.
Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.
How To Run Windows XP On AHCI Mode
Aug 7, 2012Everytime i want to swap hard disk with different OS, WinXp(IDE) to Windows 7(AHCI), i need to do change some hard disk setting on BIOS. Is there any way that i can do to make both hard disk with different OS compatible on the desktop PC without change any setting on BIOS everytime i change hdd? Is there a way to make WinXP IDE mode to run under AHCI mode?
View 1 Replies View RelatedAHCI Computer Hangs
Oct 27, 2009me as the most of you is using Windows 7 with so much fun! I do have a little problem,don't know why actually,this is why i'm here asking for help. First of all here is my hardware configuration:
Asus P5Q PRO (latest bios,waiting if Asus is ever going to release the EFI also for my motherboard lol just like happened with P5Q Deluxe,anyway).
In bios options if I select AHCI i get faster performance and system responsiveness,but from time to time,it could happen anytime,i get complete hangs up so i have to hard reboot my pc. I tried EVERYTHING,also Intel sata ahci latest driver for my motherboard and nothing works. This happens with both 32 and 64 bit of Windows 7,and it doesn't seem to happen if it's set to IDE (which definitely makes my computer less responsive). Thanks in advance to anyone that will help me
I'm beginning to thing that it's the hardisk getting insane,it's the oldest hardware component in my pc now.
Enabled AHCI, Not All Hdd In Computer?
Mar 2, 2011So I installed win 7 on a new WD 2TB Sata3 drive, I enabled AHCI before installing. I have two hdd which I use as storage, but after the reinstall only one of them show's up in my computer. I can see the other one on device manager. Does this have something to do with the AHCI? Never enabled it before now.
Setup:
Intel i7 950
Asus Sabertooth x58
3x2GB Crusial ram
AHCI Bios Setup For SSD?
Jan 10, 2012I have a SSD drive & want to use the AHCI Mode & Native Command Quening from Windows 7 Pro X64. I performed the Regedit by setting the START paramater in the registry key: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetservicesmsahci from "3" to "0" - and then making the switch in the BIOS from IDE to AHCI. Windows still would not load! The Bios screen would not load Windows 7.I have a Gigabyte GA-EP45-UD3R Board that has a Intel P45 Chipset & I installed the latest Intel Sata drivers before I tried the change. I had to use my Acronis True Image program to get Windows 7 back up & running.My Board has 6 Intel Sata ports & two Gigabyte ports on the board. I don't use the Gigabyte ports & they were left in the IDE mode in the Bios when it failed.The Bios screen loaded differently but failed as I said to load Windows 7.If I perform a clean install will Windows 7 load & install in the AHCI/Native modes with the bios setting to AHCI & not IDE? I have the SSD for programs & a 1TB HDD for storage & backup.
View 7 Replies View RelatedConfigure AHCI In Bios?
May 31, 2010Anyone who knows how to configure AHCI in bios? I'm confused I must say. I want to have eSATA with a sata slot from my motherboard.
View 4 Replies View RelatedAHCI Bios Not Installed?
Sep 2, 2011I have a new computer. When it boots up, I see AHCI Bios not installed. I do not know much about the workings of a computer. What does AHCI Bios not installed mean? My computer runs on Windows 7 and so far it seems to work just fine.
View 1 Replies View RelatedTweaking P5N-D To Find AHCI
Feb 11, 2012Trying to tweak W7-64. Can't fing AHCI in bios.
View 4 Replies View Related
