i have an ASUS M5A88-M motherboard, and a Western Digital WD2503ABYX HDD. i am trying to make that drive work in AHCI mode, but when I try, the disk won't boot. i think the HDD is AHCI compatble, tho not certain. i went into the registry to set a value=o for the relevant AHCI parameter, but no luck. if i need a full re-installation of Windows 7 64-bit, does it prompt me along the way to set the mode to IDE or AHCI?.
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
Everytime i want to swap hard disk with different OS, WinXp(IDE) to Windows 7(AHCI), i need to do change some hard disk setting on BIOS. Is there any way that i can do to make both hard disk with different OS compatible on the desktop PC without change any setting on BIOS everytime i change hdd? Is there a way to make WinXP IDE mode to run under AHCI mode?
I'm trying to do a startup repair of Windows 7 x64 on an SSD but can't boot from the CD-ROM while in AHCI mode. I have set CD-ROM at the top of the boot order in BIOS but this is just ignored and the computer boots from the SSD with the knackered version of W7x64. I read somewhere that when in AHCI mode, the BIOS boot order may include "CD-ROM" but it's not the real device anymore. I tried looking for the CD-ROM by its manufacturer name in the list under Hard Drives but it's not there either.So just how do I go about booting from the CD-ROM in AHCI mode? No problems booting if I set the BIOS back to IDE mode, install Windows 7 and then do the registry hack to install the AHCI drivers, but I'd like to be able to boot from the CD-ROM in AHCI mode.
P.S. I have a Gigabyte GA-MA78GM-US2H motherboard and am using the latest BIOS version (F9D)
My motherboard is a Gigabyte Z68XP-UD3 Revision 1.3, my OS is Windows 7 Professional 64 bit, my HDD is a Seagate 1.5tb, and my SSD is an OCZ Agility 3 60gb.
So i was using Intel Smart Response technology with my SSD for SSD caching, everything was pretty much working fine. The other day i flashed my bios using @BIOS without properly disabling my smart response configuration, which i probably shouldn't have done and i won't do again. When i rebooted, Intel Rapid Storage technology was acting up and when i tried to open it, it said "IAStorUI.exe has stopped working". After that, i uninstalled the program and tried to re-install it, but during the install it said "This computer does not meet the minimum requirements for installing the software." After a little research, i found out that it meant that my bios was set in IDE mode instead of ACHI mode. I am not sure what the mode was before i flashed my bios, but it was probably some sort of raid that it used for SSD caching. When i went into the bios and switched from IDE to AHCI, windows would blue screen after performing a few seconds of the boot logo. I switched back to IDE, and did some research to find out about the "Start" registry in HKEY_LOCAL_MACHINESYSTEMCurrentControlSetservicesmsahci. I switched that from 3 to 0, and windows was able to boot into AHCI mode and automatically got drivers. Then, i tried re-installing Intel Rapid Storage technology. It was able to install, and i rebooted my computer. It blue screened again on the same part of the boot logo as before. I had to switch back to IDE mode to get it working again. Then, i got new chipset drivers from Intel's website, which didn't help. The registry that i changed is still set to zero, but it just won't successfully boot with AHCI like it did the first time i changed the registry. I am very stumped and i dont know what i could do to make it work like it did before i flashed my bios. My friend recommended that i should reinstall windows, but then i would have to go through the trouble of getting everything back and i think there should be some way of doing this without reinstalling the os.
The bottom line is that windows blue screens when the bios is in AHCI mode, even though i have the registry that should fix that and that did fix it on one boot set to zero.
First thing, my build: Board: Gigabyte GA-P55A-UD4 CPU: Core i7 870 @ 2,93 Ghz Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18 Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD Running: Windows 7 Ultimate Trying to install: Windows 7 Ultimate PSU: LC Power Arkangel 850W
I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally.
I didn't know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the HDD? Anyway, I really want to start using the disk. I have tried installing Windows 7 from a dvd as well as from a USB key.
I changed the appropriate setting in the registry. (msachi > start: 0) Then I changed the setting in my motherboard and Windows froze upon starting up, and my system rebooted.
The thing is, I changed it to AHCI before. It worked fine! I then switched back to IDE while trying to fix a problem with eSATA detection (turned out to be a faulty cord), Now I can't switch back! Sigh. I really would like my eSATA to be plug and play.
First thing, my build: Board: Gigabyte GA-P55A-UD4 CPU: Core i7 870 @ 2,93 Ghz Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18 Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD Running: Windows 7 Ultimate Trying to install: Windows 7 Ultimat PSU: LC Power Arkangel 850W Ok so here's the deal. I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally. I didnt know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the disk? Note: I have tried installing Windows 7 from a dvd as well as from a USB key.
I'm installing Seven on a WinXP machine and completed the install, but forgot to change the SATA setting in the bios from "compatibility mode" to AHCI. Now when I change it, windows gives me bluescreen on boot.I'm dumbfounded that Windows Seven startup repair can't fix a problem this simple, but it completely failed, wasn't even able to find a problem.I was thinking it might be easier to just reformat and begin the install over again, or startup in safemode and install the intel SATA drivers... assuming it will let me boot into safemode with AHCI enabled.ps. On the other computer (different thread), I'm going to wait till I have several hours of uninterrupted time, in case I need to begin over installing all the windows versions one at a time. I'll reply with any success/failure on that thread later in the week.
I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.
A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.
If the BIOS setting for the hard drive controller is AHCI it will not recognize the drive. (This was the default setting in the BIOS), If changed to IDE mode it recognizes the drive but come up with an "No operating system detected" message. If the hard drive is installed in a second lap top it works fine. If another hard drive is installed it works fine in AHCI mode. Only the combination of the original hard drive and the original lap top wont work.
i'm working with a new pc build that uses a 60 gb ssd for its boot drive, and which is also reusing some "old" sata hdds for storage.
at the time i installed windows 7 ult 64, i had only a new ssd plugged in, and the bios was set to ahci mode. the installation went fine and i was able to boot into windows afterwards without issue.
then, i connected a wd caviar black sata hdd to use as storage, with the ssd being the boot drive. with both of them connected, windows will not get past the starting windows screen.
i made this video of the program before i understood that it was a drive controller issue: startup problem - Internet in it, you can see that windows boots fine in ahci mode with just the ssd plugged in, but that when the backup sata drive is also connected it doesn't get past the starting windows screen.
for the record, this caviar black hdd was my previous boot os, and it also has a windows 7 install on it (which i've renamed the base folder of), but it is not booting from that hdd. also, i have tried the same thing with other "old" sata hdds that do not have any previous windows install on them, and the result is the same thing which is shown in the video.
I created a system image on an AHCI system, then I replaced the hard drives & re-imaged the system. Now Windows won't boot in AHCI mode, it has to be it IDE mode. Why is it not booting in AHCI mode?
I successfully installed Windows 7 64bit in AHCI mode on a PC with 3 new 3TB Western Digital WD30EZRX Caviar Green hard drives.Then I installed "Intel Matrix Storage Manager Driver [v8.9.0.1023]" & as soon as Windows restarted after installing it, Windows would not boot, & will now only boot in IDE mode.In IDE mode I have to do a system restore to the point before installation of "Intel Matrix Storage Manager Driver" to be able to boot again in AHCI mode.
Can someone hit me with a link for manually installing the AHCI driver and switching the OS mode for the storage controller.
If I remember right, this is just putting the driver in /sys/drivers, running a script, and making a registry change. Then you reboot, change the motherboard setting, and then install IMSM after the OS comes back up. I don't remember the script, or if it was just a reg edit, etc.
I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.
As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.
I recently swapped out my motherboard for a Gigabyte GA-970A-UD3. I was trying to overclock my CPU and after a crash and CMOS reset I was no longer able to complete WEI. This was fixed by reinstalling the BIOS firmware but when I ran WEI again, I was now getting a 5.9 score for my SSD (OCZ Agility) when it was previously 7.2.
Now I can no longer get Windows to use the AHCI driver (neither MS nor AMD) for the drive. I am running in AHCI mode but the driver being used for the SSD is a generic "disk drive" (disk.sys and partmgr.sys). When I try to update this driver, it tells me I am using the latest one; it also does not let me manually select the AHCI driver.
After multiple attempts at switching back and forth between IDE and AHCI in the BIOS, uninstalling and reinstalling AMD AHCI drivers, nothing changes. Still the same 5.9 WEI score and generic driver.
I have SSD as primary system drive and 2x512GB HDDs as RAID 1 for storage.In bios i have options to set them as AHCI, IDE and one more that i forgot...
Is there any real noticable benefit from having a SATA mechanical HDD use AHCI or IDE? Also, if there is any benefit, is it related to the rpm speed that the drive is capable of?I keep reading conflicting reports on this, some say AHCI is best, others say there is no real difference unless the disk is an SSD.I am about to do a clean install of Windows 7 on a laptop 5400rpm mechanical HDD so thought I may as well set the mode before proceeding with the install.
I recently installed Windows 7 Home Premium on a new blank SATA hard drive which I had formatted using the default settings under Windows XP Disk Management.Prior to installing Windows 7 on this PC, I disconnected my other SATA hard drives to preclude any issues during formatting/installation.What I would like to know is whether changing the BIOS disk access mode from IDE to AHCI will impact my ability to access my old hard drives (once I reconnect them)?
I recently purchased a HP 8440p laptop with Windows 7 Pro. installed. I dicided to partition the drive and install XP-Sp3 on the newly partitioned drive. Before I could load XP I had to change the configuration to IDE. Once I did that all went fine. Now in order to run betwwen OS's I have to set my configuration AHCI for W7 and IDE for XP.
Is there a better way of doing this beside alway re-configuring the bios for AHCI or IDE?
Driver update program says new driver available 1.0. Any issues regarding updating this driver. No problems needed. Dell Inspirion laptop Win 7 Home Prem. 64bit 4gb ram
I have found on 4 different boards if I install in AHCI mode, Windows 7 seems to "find" the drivers for running in AHCI/RAID mode at install. If I install in IDE mode, it does not and I have no option to switch to AHCI/RAID if needed. In the past you had to press F6 (or whatever) and install them from a floppy. I think this is no longer the case with Windows 7. Can anyone confirm this. I don't even have a floppy and never will. I will install in AHCI so I have the choice in the future. Is there any down side to doing this and am I right?
Also - I know there is a registry "hack" you can use to boot into AHCI after installing in IDE but why does everyone not install in AHCI so they have the choice? Am I way off here? Are you planning to install in AHCI to have this benefit?
In the BIOS on a laptop the disk choice can enable SATA as IDE or AHCI.
If I chose IDE do I actually lose any disk performance -- having IDE makes it easier to have Windows XP as a dual boot system without having to hunt down all the SATA drivers and slip stream an XP disk.
Remember this is a LAPTOP not a desktop so disk performance won't be that great in any case.
me as the most of you is using Windows 7 with so much fun! I do have a little problem,don't know why actually,this is why i'm here asking for help. First of all here is my hardware configuration:
Asus P5Q PRO (latest bios,waiting if Asus is ever going to release the EFI also for my motherboard lol just like happened with P5Q Deluxe,anyway).
In bios options if I select AHCI i get faster performance and system responsiveness,but from time to time,it could happen anytime,i get complete hangs up so i have to hard reboot my pc. I tried EVERYTHING,also Intel sata ahci latest driver for my motherboard and nothing works. This happens with both 32 and 64 bit of Windows 7,and it doesn't seem to happen if it's set to IDE (which definitely makes my computer less responsive). Thanks in advance to anyone that will help me
I'm beginning to thing that it's the hardisk getting insane,it's the oldest hardware component in my pc now.
So I installed win 7 on a new WD 2TB Sata3 drive, I enabled AHCI before installing. I have two hdd which I use as storage, but after the reinstall only one of them show's up in my computer. I can see the other one on device manager. Does this have something to do with the AHCI? Never enabled it before now.
Setup: Intel i7 950 Asus Sabertooth x58 3x2GB Crusial ram
I have a SSD drive & want to use the AHCI Mode & Native Command Quening from Windows 7 Pro X64. I performed the Regedit by setting the START paramater in the registry key: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetservicesmsahci from "3" to "0" - and then making the switch in the BIOS from IDE to AHCI. Windows still would not load! The Bios screen would not load Windows 7.I have a Gigabyte GA-EP45-UD3R Board that has a Intel P45 Chipset & I installed the latest Intel Sata drivers before I tried the change. I had to use my Acronis True Image program to get Windows 7 back up & running.My Board has 6 Intel Sata ports & two Gigabyte ports on the board. I don't use the Gigabyte ports & they were left in the IDE mode in the Bios when it failed.The Bios screen loaded differently but failed as I said to load Windows 7.If I perform a clean install will Windows 7 load & install in the AHCI/Native modes with the bios setting to AHCI & not IDE? I have the SSD for programs & a 1TB HDD for storage & backup.
I have a new computer. When it boots up, I see AHCI Bios not installed. I do not know much about the workings of a computer. What does AHCI Bios not installed mean? My computer runs on Windows 7 and so far it seems to work just fine.