Restored Windows 7 HP 64bit System Image - Won't Boot In AHCI Mode
Jun 29, 2011
I created a system image on an AHCI system, then I replaced the hard drives & re-imaged the system. Now Windows won't boot in AHCI mode, it has to be it IDE mode. Why is it not booting in AHCI mode?
View 5 Replies
ADVERTISEMENT
Jan 22, 2011
My Win7 HP x64 PC has two hard drives, each partitioned into two volumes:
My C: and E: drives are each half of a 200GB drive, both NTFS.
My D: and F: drives are each half of a newer, 1TB drive, both NTFS.
My F: drive has around 400GB of 'stuff' that I want to preserve.
I've been trying to migrate the win7 installation from C: to the first partition of the 1TB drive with two different tools (Norton Ghost and the built-in Windows backup utility) and both fail identically.The backup procedure itself appears to work in both cases.Restoring the backup to the first partition of the 1TB drive "works" in so much as I don't get any errors either way.Creating the requisite boot structures also work, as the O/S appears to be bootable.However, when the restored O/S makes it to the login screen, two flaws are evident:
1. The keyboard absolutely does not work.
2. If I log in on an account that doesn't need a keyboard (no password), I see "Loading desktop", then a few seconds "Logging out" and I'm back at the login screen.
If I look at the event viewer logs (booting up with the O/S on the smaller drive), I see numerous events like this:"The AVGIDSAgent service failed to start due to the following error: The system cannot find the file specified.""The Windows Live ID Sign-in Assistant service failed to start due to the following error: The system cannot find the file specified."
[code]....
View 1 Replies
View Related
Nov 10, 2011
I just installed a new hard drive after my previous one failed to start up. I have a backup image stored on an external WD Passport. The install went well. I turn on my tower with the Windows 7 recovery disc in, start up System Image Restore and plug in my Passport. The system restore recognizes my Passport and when I go through the wizard to reformat and partition the disk to match the layout of the recovery image, I get an error message saying "The system image restore failed. No disk that can be used for recovering the system disk can be found. *hyperlink* Details."Details states, "No disck that can be used for recovering the system disk can be found. Try the following: 1) A probable system disk may have been excluded by mistake. a. Review the list of disks that you have excluded from the recovery for a likely disk. b. Type LIST DISK command in the DISKPART command interpreter. The probable system disk is usually the first disk listed. c. If possible,, remove the disk from the exclusion list and then retry the recovery.Tried that, my disk is not listed as an exclusion.2) A USB disk may have been assigned as a system disk. a. Detach all USB disks from the computer. b. Reboot into Windows Recovery Environment then reattach USB disks and retry the recovery.
View 1 Replies
View Related
Jun 27, 2011
After restoring my pc from a system image, when windows resarts, it won't boot, & I'm taken to the "startup repair" option screen. After Startup Repair is performed I get the message "Startup Repair Cannot Repair This Computer Automatically" with the following problem details:
Problem Event Name: StartupRepairOffline
Problem Signature 01: 6.1.7600.16385
Problem Signature 02: 6.1.7600.16385
Problem Signature 03: unknown
Problem Signature 04: 52
Problem Signature 05: AutoFailover
Problem Signature 06: 1
Problem Signature 07: BadPatch
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
It says that the root cause found is "A patch is preventing the system from starting" Error code = 0x490.
View 9 Replies
View Related
Jul 5, 2011
I successfully installed Windows 7 64bit in AHCI mode on a PC with 3 new 3TB Western Digital WD30EZRX Caviar Green hard drives.Then I installed "Intel Matrix Storage Manager Driver [v8.9.0.1023]" & as soon as Windows restarted after installing it, Windows would not boot, & will now only boot in IDE mode.In IDE mode I have to do a system restore to the point before installation of "Intel Matrix Storage Manager Driver" to be able to boot again in AHCI mode.
View 1 Replies
View Related
Jan 6, 2009
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
View 0 Replies
View Related
Feb 9, 2011
I'm trying to do a startup repair of Windows 7 x64 on an SSD but can't boot from the CD-ROM while in AHCI mode. I have set CD-ROM at the top of the boot order in BIOS but this is just ignored and the computer boots from the SSD with the knackered version of W7x64. I read somewhere that when in AHCI mode, the BIOS boot order may include "CD-ROM" but it's not the real device anymore. I tried looking for the CD-ROM by its manufacturer name in the list under Hard Drives but it's not there either.So just how do I go about booting from the CD-ROM in AHCI mode? No problems booting if I set the BIOS back to IDE mode, install Windows 7 and then do the registry hack to install the AHCI drivers, but I'd like to be able to boot from the CD-ROM in AHCI mode.
P.S. I have a Gigabyte GA-MA78GM-US2H motherboard and am using the latest BIOS version (F9D)
View 2 Replies
View Related
Mar 31, 2012
My motherboard is a Gigabyte Z68XP-UD3 Revision 1.3, my OS is Windows 7 Professional 64 bit, my HDD is a Seagate 1.5tb, and my SSD is an OCZ Agility 3 60gb.
So i was using Intel Smart Response technology with my SSD for SSD caching, everything was pretty much working fine. The other day i flashed my bios using @BIOS without properly disabling my smart response configuration, which i probably shouldn't have done and i won't do again. When i rebooted, Intel Rapid Storage technology was acting up and when i tried to open it, it said "IAStorUI.exe has stopped working". After that, i uninstalled the program and tried to re-install it, but during the install it said "This computer does not meet the minimum requirements for installing the software." After a little research, i found out that it meant that my bios was set in IDE mode instead of ACHI mode. I am not sure what the mode was before i flashed my bios, but it was probably some sort of raid that it used for SSD caching. When i went into the bios and switched from IDE to AHCI, windows would blue screen after performing a few seconds of the boot logo. I switched back to IDE, and did some research to find out about the "Start" registry in HKEY_LOCAL_MACHINESYSTEMCurrentControlSetservicesmsahci. I switched that from 3 to 0, and windows was able to boot into AHCI mode and automatically got drivers. Then, i tried re-installing Intel Rapid Storage technology. It was able to install, and i rebooted my computer. It blue screened again on the same part of the boot logo as before. I had to switch back to IDE mode to get it working again. Then, i got new chipset drivers from Intel's website, which didn't help. The registry that i changed is still set to zero, but it just won't successfully boot with AHCI like it did the first time i changed the registry. I am very stumped and i dont know what i could do to make it work like it did before i flashed my bios. My friend recommended that i should reinstall windows, but then i would have to go through the trouble of getting everything back and i think there should be some way of doing this without reinstalling the os.
The bottom line is that windows blue screens when the bios is in AHCI mode, even though i have the registry that should fix that and that did fix it on one boot set to zero.
View 1 Replies
View Related
Apr 30, 2011
A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.
View 9 Replies
View Related
Sep 8, 2011
I periodically create a disk image of a RAID 1 Volume consisting of two 500 GB SATA drive containing my Windows 7 system and data, and a RAID 0 Volume consisting of of three 320 GB SATA drives containing my Windows Vista. I tried to do a recovery from the disk image, but my VISTA volume does not restore. Is there anyway to restore both volumes? The recovery indicates the both volumes are to be restored, both only the Windows 7 volume is restored.
View 7 Replies
View Related
Aug 15, 2011
my computer crashed last night and when I have tried to switch it on since it gives me the above message.I have tried entering setup by pressing F2 and changing the hard disk to be the primary boot device, but the same thing occurs.I have created a Windows 7 32-Bit recovery disk by downloading the iso file on my dad's pc and burning that to a dvd. I am able to load this, but when it first starts up it has a table supposed to list operating systems but it is blank and I cannor select anything. It says if my operating system isn't listed, "click load drivers and install drivers for your hard disks" but I don't know where on earth these are located and neither does google seem to.then working through the option on the menu:
-if I click start-up repair it tells me "startup repair cannot repair this computer automatically"
-if I click system restore I get an error message saying I must specify which windows installation to restore
-if I click system image recover it gives me an error message saying "windows cannot find a system image on this computer" and if I try to select one none appear.
View 10 Replies
View Related
Aug 30, 2011
After restoring an image made with Clonezilla that used to work, Windows 7 is unable to start. When prompted, I used the DVD, but it still fails with "Startup Repair could not detect a problem".When rebooting, it says "Windows Error Recovery: Launch Startup Repair (recommended) and Start Windows Normally": Launch Startup Repair fails with "Windows Boot Manager: 0xc000000e The Boot selection failed because a required device is inaccessible".FWIW, to investigate, I deleted both partitions (#1 to hold the OS, #2 to hold images) and re-created them with enough space to hold (#1 was made a bit bigger because I didn't know how to specify infos in cfdisk accurately), and Clonezilla happily restored the image.
View 6 Replies
View Related
Oct 15, 2012
I am attemptin to make a backup image of my hard drive. The new Image will be complied on an external hard. The drive has a 1TB Capacity with 450 Gigs free. I am receiving an error code during the image compilation stating that there is a problem with the I/O device. I ran chkdsk and found no problems. I also switched USB ports just to rule that out. I have used this same external hard drive to image a different laptop with no issues last week. My next approach would be to try this in safe mode. When I am in safe mode, I cannot find the location of the software which windows uses to create the image. I typed the location into the address bar and it pulled up a link in the address bar which took me back to the control panel. Can anyone tell me if this is possible to do in safe mode and if not, what my next step would be. Windows error: The Operation failed due to a device error encountered with either the source or destination. If the source or destination volume is on a disk, run CHKDSK/R on the source or destination volume and then retry the operation. (0x8078012D) Additional Information: The request could not be performed because of an I/O device error (0x8007045D)?
View 2 Replies
View Related
May 8, 2012
I want to make a recovery disc to reset my entire 4 partition dual boot hard drive back to its current state. the recovery would reset both xp and win 7 which i have dual booting. can i make one single image to do this without it screwing up my boot loaders etc? what should i use? 3rd party software?
View 9 Replies
View Related
Aug 7, 2012
Everytime i want to swap hard disk with different OS, WinXp(IDE) to Windows 7(AHCI), i need to do change some hard disk setting on BIOS. Is there any way that i can do to make both hard disk with different OS compatible on the desktop PC without change any setting on BIOS everytime i change hdd? Is there a way to make WinXP IDE mode to run under AHCI mode?
View 1 Replies
View Related
Mar 29, 2012
When I try to wake my machine from S3 sleep mode I see the hard drive lights power up but nothing happens, I get a black screen for about 5-6 seconds then my machine proceeds to boot loop itself until i manual shut it down with the power button. Sometimes it will start up regularly with no problems, and about 60-70% of the other times it will do the problem i have explained above.
View 1 Replies
View Related
Oct 27, 2012
Can XP mode run a program with 32 Bit OS requirement?
View 2 Replies
View Related
Feb 28, 2010
I WAS in 64 bit mode but had a system failure and had to reinstall.Since then I haven't been able to install in 64 bit mode. No matter what I try it always installs the 32 bit version.I've even re-partitioned my hard drive in order to get a completely fresh install. But nothing seems to work.Windows "knows" my system in 64 bit capable. In the Control Panel - View basic info about your computer it shows my processor as "AMD Athlon 64 X2 Dual Core Processor 4600+ 2.4 GHz".Is there a way coerce a 64 bit install?
View 3 Replies
View Related
Feb 28, 2011
My Windows 7 Ultimate 32bit OS got messed up so I restored the original image I made from DriveImage XML successfully. Now when my PC boots, I get the mobo splash screen and then just a cursor. When I put my Win 7 install disk in I can "press any key" to boot from it and the DVD goes right to where I can repair my installation. It sees my partition and when I use the cmd prompt using diskpart, I can see that the win 7 volume is c:, active, and all my files are in the right spot. However when I look at the volume numbers, my c: is volume 2 and my DVD drives are volumes 1 & 2. So how do I change my c: drive to volume 0? I've read that this is how you set the c: to boot properly.
The Win 7 drive is a WD 500gb IDE. When I put this drive into any other PC, it does the same thing. Mobo splash or POST screen then just a cursor. I can't enter Safe Mode or anything except to put a disc in the DVD drive and boot from it. I tried fiddling with my mobo settings and they are normal. If I take my Win 7 drive out and put it as a slave or as a USB external drive, I can see everything and do whatever with the files.
View 4 Replies
View Related
Feb 28, 2011
My Windows 7 Ultimate 32bit OS got messed up so I restored the original image I made from DriveImage XML successfully. Now when my PC boots, I get the mobo splash screen and then just a cursor. When I put my Win 7 install disk in I can "press any key" to boot from it and the DVD goes right to where I can repair my installation. It sees my partition and when I use the cmd prompt using diskpart, I can see that the win 7 volume is c:, active, and all my files are in the right spot. However when I look at the volume numbers, my c: is volume 2 and my DVD drives are volumes 1 & 2. So how do I change my c: drive to volume 0? I've read that this is how you set the c: to boot properly.
View 1 Replies
View Related
Jan 8, 2013
My Old HDD crashed, it had windows 7 x64 on a D: logical drive with an extended partition. My old HDD also had two other primary partitions one of which probably had some system/boot files etc,. I do not have a backup of these two primary partitions, however, I do have a paragon backup of my logical drive D: extended partition. I got me a new HDD, created a new NTFS primary partition with a drive letter C:. I then restoed the paragon backup of my windows D: drive on to this new primary C: partition. Now, I am not able to boot windows 7. Seems like I need to create a new system partition with boot files to be able to boot my Win 7.
View 7 Replies
View Related
Feb 28, 2011
My Windows 7 Ultimate 32bit OS got messed up so I restored the original image I made from DriveImage XML successfully. Now when my PC boots, I get the mobo splash screen and then just a cursor. When I put my Win 7 install disk in I can "press any key" to boot from it and the DVD goes right to where I can repair my installation. It sees my partition and when I use the cmd prompt using diskpart, I can see that the win 7 volume is c:, active, and all my files are in the right spot. However when I look at the volume numbers, my c: is volume 2 and my DVD drives are volumes 1 & 2. So how do I change my c: drive to volume 0? I've read that this is how you set the c: to boot properly.
View 5 Replies
View Related
Jan 24, 2011
First thing, my build:
Board: Gigabyte GA-P55A-UD4
CPU: Core i7 870 @ 2,93 Ghz
Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18
Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD
Running: Windows 7 Ultimate
Trying to install: Windows 7 Ultimate
PSU: LC Power Arkangel 850W
I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally.
I didn't know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the HDD? Anyway, I really want to start using the disk. I have tried installing Windows 7 from a dvd as well as from a USB key.
View 5 Replies
View Related
Jan 1, 2012
I changed the appropriate setting in the registry. (msachi > start: 0) Then I changed the setting in my motherboard and Windows froze upon starting up, and my system rebooted.
The thing is, I changed it to AHCI before. It worked fine! I then switched back to IDE while trying to fix a problem with eSATA detection (turned out to be a faulty cord), Now I can't switch back! Sigh. I really would like my eSATA to be plug and play.
View 4 Replies
View Related
Jan 24, 2011
First thing, my build: Board: Gigabyte GA-P55A-UD4 CPU: Core i7 870 @ 2,93 Ghz Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18 Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD Running: Windows 7 Ultimate Trying to install: Windows 7 Ultimat PSU: LC Power Arkangel 850W
Ok so here's the deal. I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally. I didnt know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the disk? Note: I have tried installing Windows 7 from a dvd as well as from a USB key.
View 7 Replies
View Related
Jun 9, 2011
AHCI Port Error 0 Press F2 to continue. This error shows on my Gateway zx4800 but when I press F2 nothing happens. S.M.A.R.T capable and status BAD.....it also show this above the AHCI error. My hdd works with other PC.
View 2 Replies
View Related
May 10, 2012
I am attempting to restore from a system image, but keep receiving a boot manager error message: Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible
The computer boots no problem normally, it is only when restarting to restore the system image.
View 4 Replies
View Related
Jul 22, 2012
My Dell laptop is saying BOOTMGR image is corrupt. the system cannot boot.
View 3 Replies
View Related
Jul 20, 2012
just moved my uncles HDD to a SSD i finally got it to boot no problem andeverything seems to be back to normal but a new issue has come up.every 5th or 6th time i reboot it gives me the BOOTMGR image is corrupt. The system cannot boot error then after i restart go into the BIOS go save to CMOS the system boots as if nothing happened. so far i have tried: run startup repair run bootrec.exe /fixmbr /fixboot and fix bcd commands x4 strangely it says everything is completed but shows 0 indows installs.reinstalled Win 7 no virues no spyware I'm thinking of maybe changing the CMOS battery.
View 3 Replies
View Related
Nov 11, 2011
i'm working with a new pc build that uses a 60 gb ssd for its boot drive, and which is also reusing some "old" sata hdds for storage.
at the time i installed windows 7 ult 64, i had only a new ssd plugged in, and the bios was set to ahci mode. the installation went fine and i was able to boot into windows afterwards without issue.
then, i connected a wd caviar black sata hdd to use as storage, with the ssd being the boot drive. with both of them connected, windows will not get past the starting windows screen.
i made this video of the program before i understood that it was a drive controller issue: startup problem - Internet in it, you can see that windows boots fine in ahci mode with just the ssd plugged in, but that when the backup sata drive is also connected it doesn't get past the starting windows screen.
for the record, this caviar black hdd was my previous boot os, and it also has a windows 7 install on it (which i've renamed the base folder of), but it is not booting from that hdd. also, i have tried the same thing with other "old" sata hdds that do not have any previous windows install on them, and the result is the same thing which is shown in the video.
View 9 Replies
View Related
Jul 31, 2011
All discussion will pertain to Windows 7 Backup w/ NTFS disks w/ample space. Period. It shouldn't matter if the disks are simple or dynamic. The simple situation is this: I have one simple NTFS boot disk that failed months after system image backups to my other internal HDD. So then I replace this boot disk w/ a new one. So Am I able to restore the system image from the HDD onto to the new boot disk?
View 4 Replies
View Related