Windows 7 X64 Won't Boot On A New HDD Restored Partition
Jan 8, 2013
My Old HDD crashed, it had windows 7 x64 on a D: logical drive with an extended partition. My old HDD also had two other primary partitions one of which probably had some system/boot files etc,. I do not have a backup of these two primary partitions, however, I do have a paragon backup of my logical drive D: extended partition. I got me a new HDD, created a new NTFS primary partition with a drive letter C:. I then restoed the paragon backup of my windows D: drive on to this new primary C: partition. Now, I am not able to boot windows 7. Seems like I need to create a new system partition with boot files to be able to boot my Win 7.
My Windows 7 Ultimate 32bit OS got messed up so I restored the original image I made from DriveImage XML successfully. Now when my PC boots, I get the mobo splash screen and then just a cursor. When I put my Win 7 install disk in I can "press any key" to boot from it and the DVD goes right to where I can repair my installation. It sees my partition and when I use the cmd prompt using diskpart, I can see that the win 7 volume is c:, active, and all my files are in the right spot. However when I look at the volume numbers, my c: is volume 2 and my DVD drives are volumes 1 & 2. So how do I change my c: drive to volume 0? I've read that this is how you set the c: to boot properly.
The Win 7 drive is a WD 500gb IDE. When I put this drive into any other PC, it does the same thing. Mobo splash or POST screen then just a cursor. I can't enter Safe Mode or anything except to put a disc in the DVD drive and boot from it. I tried fiddling with my mobo settings and they are normal. If I take my Win 7 drive out and put it as a slave or as a USB external drive, I can see everything and do whatever with the files.
My Windows 7 Ultimate 32bit OS got messed up so I restored the original image I made from DriveImage XML successfully. Now when my PC boots, I get the mobo splash screen and then just a cursor. When I put my Win 7 install disk in I can "press any key" to boot from it and the DVD goes right to where I can repair my installation. It sees my partition and when I use the cmd prompt using diskpart, I can see that the win 7 volume is c:, active, and all my files are in the right spot. However when I look at the volume numbers, my c: is volume 2 and my DVD drives are volumes 1 & 2. So how do I change my c: drive to volume 0? I've read that this is how you set the c: to boot properly.
My Windows 7 Ultimate 32bit OS got messed up so I restored the original image I made from DriveImage XML successfully. Now when my PC boots, I get the mobo splash screen and then just a cursor. When I put my Win 7 install disk in I can "press any key" to boot from it and the DVD goes right to where I can repair my installation. It sees my partition and when I use the cmd prompt using diskpart, I can see that the win 7 volume is c:, active, and all my files are in the right spot. However when I look at the volume numbers, my c: is volume 2 and my DVD drives are volumes 1 & 2. So how do I change my c: drive to volume 0? I've read that this is how you set the c: to boot properly.
I created a system image on an AHCI system, then I replaced the hard drives & re-imaged the system. Now Windows won't boot in AHCI mode, it has to be it IDE mode. Why is it not booting in AHCI mode?
I'm building a new computer. Can I partition the hard disk, copy my laptop HD to boot from one partition and run a new windows 7 pro os from the second partition?
I'm a long-time reader but new poster. I am currently running Windows 7. I want to install Windows XP onto another disc and have a dual-boot setup. I keep Windows 7 up to date and secure, but for the XP partition, I would rather not have antivirus running or even installed, in order to limit background processes. I will not be logging into any place or making any credit card purchases when booted into Windows XP. It will just be used for surfing, games, etc. Further, if and when XP becomes compromised or buggy, I will simply overwrite the partition with a backup image.
If I use Bitlocker to lock down the Windows 7 partition (with the encryption key on a thumb drive) and boot into Windows XP, am I correct in thinking the XP installation see or can't access the Windows 7 partition? If XP gets compromised, can a virus access or write to the Windows 7 partition?
Is there any other reason why this would not be secure? Can a virus write to the BIOS?
this is what I did, since I have no CD-ROM, to install Windows 7 I created a partion X: NTFS and set it as the ACTIVE ONE, the put there the Windows 7 installation files, and opened prompt command to type bootsect.exe /n60 X: , next I restarted my computer, and automatically it booted into the Windows 7 setup, I installed Windows 7 on the partition C: and formatted the partition C:, everything installed and after the installation finished, a multiple choice menu appears that reads:[CODE]
I have Windows 7 ultimate 64-bit installed on DELL desktop (Optiplex 990) i7 Core. I have two HDD: Disk 0 contains the operating system 500GB. and Disk 1 empty 1TB.
I want to make a partition on disk 1 to mirror the operating system partition and keep the remaining for data storage. I tried to do but I had the following error message: "All disks holding extents for a given volume must have the same sector size, and the sector size must be valid."
I have a Boot Camped Mac Mini with Windows 7. I recently needed to allocate more disk space to it as i only had a gig left, i booted into MacOS and used Disk Utility to make the Mac partition smaller, i rebooted into windows and downloaded software called 'Partition Wizard' from www.partitionwizard.com. I dragged the Windows partition all the way so that it used up all the Unallocated Space, it required a reboot to finsih and when it did it displayed an error such as thistatus:0xc0000255Info: The Windows Boot Configuration Data file is missing required informationI have the Installation Disk and i have tried repairing more than 3 times and it seemed to do nothing, so i tried using the CMD and bootrec.exe and now when i start the repair wizard it says there is no windows partition yet i can still try repairing things (Yet still does not repair anything). I downloaded EasyBCD but im on my Mac partition right now and its an exe, i have no clue how to run that within windows to try and repair the Bootloader. I do however have access to the BOOTCAMP partition through the mac side, and i can access all the files. Is there some way i can repair the bootloader through this?
My sister was on my laptop, when the screen froze, she pushed the power-off button to turn it off. When I tried to restart it later, there was this green screen giving me the option of making a backup or to restore. I chose to restore, and after that was completed, my computer would load normally, except now it says msn "stopped working" and when I go to my homepage (google) it loads normally, but when I tryto search something, it says Internet explorer stopped working and tells me to close the program.
I have restored 7 Ultimate from backup, HDD crash. Only thing, it will not sleep/suspend. I have tried tweaking the power options to no avail. Thought it may be Crap Cleaner deleting a registry key but restoring reg from backup, then rebooting did not work. When I hit sleep it justs goes to logon screen, if I deselect password on resume it just dims screen & dumps at desktop.
I periodically create a disk image of a RAID 1 Volume consisting of two 500 GB SATA drive containing my Windows 7 system and data, and a RAID 0 Volume consisting of of three 320 GB SATA drives containing my Windows Vista. I tried to do a recovery from the disk image, but my VISTA volume does not restore. Is there anyway to restore both volumes? The recovery indicates the both volumes are to be restored, both only the Windows 7 volume is restored.
I currently have Windows 7 64 bit installed in two partiions:C: drive and E drive. Everytime I start, windows from the C: partition automatically boots. How do I get the Windows from E drive to boot? Ultimately I'd like to use the windows from E drive (which has all my installed software) and delete the one from C: drive. The problem is that I installed the one on C: drive most recently. (Long story short, I tried to delete and old version of windows unsuccessfully, and had to unmount and reformat the partition.)When I go to System Configuration under the Boot tab, I only see Windows in one partition (C: drive), so it won't allow me to delete that.
I normally run Windows 7. Today I decided to try out Windows 8 as well. I went into Disk manager and created a partition. I then booted off of my Windows 8 DVD and installed it on that partition. Now, my computer is only booting into Windows 8. What I really want is an option to choose which OS to boot into, but I would really like to be able to get back to Windows 7.
I installed Windows 7 on my second hard drive g: (1st partition drive 1) and Windows set up a dual boot with Windows XP on the C: drive (1st partition drive 0) and Windows 7 on the G: drive (1st partition drive 1). Everything worked fine for months until I decided to dump Windows XP to try out Windows 8. I created an Win 8 installation USB FOB. I deleted the old XP Partition on C: then the install failed and I could not boot, (c: was deleted).No problem (I thought), I just swapped the hard drives to boot off my Windows 7 partition. Surprise! It won't boot either. I tried using partition Wizard to repair the MBR, from another computer. That didn't workThen I created a Windows 7 installation USB FOB (no CD drive on target computer), to see if Windows repair would take care of the problem. It could find no Windows installation. So I selected start up repair, it ran for a few minutes then said it was going to reboot, so I pressed the finish button.[CODE]
After restoring an image made with Clonezilla that used to work, Windows 7 is unable to start. When prompted, I used the DVD, but it still fails with "Startup Repair could not detect a problem".When rebooting, it says "Windows Error Recovery: Launch Startup Repair (recommended) and Start Windows Normally": Launch Startup Repair fails with "Windows Boot Manager: 0xc000000e The Boot selection failed because a required device is inaccessible".FWIW, to investigate, I deleted both partitions (#1 to hold the OS, #2 to hold images) and re-created them with enough space to hold (#1 was made a bit bigger because I didn't know how to specify infos in cfdisk accurately), and Clonezilla happily restored the image.
This tutorial describes how to install Windows XP and Windows 7 on the same partition (first tutorial for one partition written).The short concept: Install XP twice and have 7 replace the first installation.Need more testers to confirm it works for everyone and the instructions are clear enough.Requirements: Both Installation discsA Windows XP LiveCD (might work with other OS, but no guarantees)EasyBCD.Install Windows XP normally if you're not already running it.Don't bother installing any drivers or software on it.Start another installation of Windows XP. Choose the same hard drive and leave it unchanged without formatting. When it asks you what to do then choose to install in a different directory "C:Windows.xp".Finish installing that one and only the necessary drivers.afterwards.Install Windows 7 on C: over the regular C:windows. A warning will tell you that it will move the old files to "Windows.old" directory. The good thing is it doesn't touch the Windows.xp directory.Install and run EasyBCD. Go to "Add/Remove Entries" and add an entry of "Windows NT/2k/XP/2k3" type and a name of your choice. (as shown in the attached image)Don't forget the "Save" button.You may also want to adjust the loader timeout from "Change Settings".In C: you will find a (hidden) file "boot.saved". Open it, remove the entry to the "WINDOWS" directory and make the "WINDOWS.XP" your default one (if it's not) and save as boot.ini".Restart and boot from the Windows XP LiveCD (which you should have burned and tested on CD or DVD before starting).Open the Command Prompt (Run "cmd") and enter the following lines in order
I installed Win7 on the same Partition as WinXP. I was in a hurry and forgot totally to partition the HD before I installed, was doing 100 things on the side during the Installation, and noticed my mistake only after the install was complete. Is there any way I can do a Multi boot for those two OS now? The WinXP folder has been renamed to Windows.old, and even with EasyBCD there's no way I can get the Comp to boot into WinXP.
I recently installed a 90GB Kingston Technology SSD and then created a shadow copy of my previous hard drive (which was 62.4GB), meaning that currently I only have access to this amount of space on the new hard drive.
resize this boot partition to allow me to use all the space currently unallocated?
So long story short, my current os (w7) is installed on a non-boot partition of a now internal drive that used to be external. This wasn't an issue/I didn't notice because I had another unused internal hdd which DID have an old bootable os partition, and then I'd just choose the correct instance of Windows when that one booted.I have to get rid of the old HDD with the bootable partition. Is there anyway I can change the non bootable my currant OS is on to a bootable partition (ie thru windows, cmd, bios etc)
Is there a way to install Windows 7 in a different folder than the default Windows and on a different partition than the boot. For example, I have XP installed on my Laptop that has 3 partitions C:, D:, E:. C: is my boot partition and D: is where I have XP install in directory D:OSWINXP and E: where applications are installed and data is store.
I like to install Windows 7 and have C: as the boot drive and install it on D: in the sub directory D:OSWindows or D:OSWindows 7.
I installed DOS into 2GB FAT 16, then installed Windows 7 Ultimate expecting Windows 7 to install itself in a partition with a drive letter other than C (just as XP had done in a previous dual-boot setting with DOS) But no, Windows 7 has hijacked the C drive letter for itself. How can I stop Windows 7 from "stealing" from DOS, the drive letter C, for itself?
I tried resizing my C drive but got an error message. It said something about dynamic discs ??after that when i tried to restart my hp laptop i got this error message:The message on boot states "windows failed to load. A recent hardware or software change may be the cause."The status is "Oxc000000f".The description is "The boot selection failed because a required device is inaccessible"what can i do to fix this problem? i am running check disc like the system suggested, but if it doesn't give me a solution will i need to re install or recover Windows 7 with my back up discs or using HP's system recovery?
I want to have a boot partition, system partition and have a separate storage partition for all of my files. I am a bit confused about the boot partition/system partition relationship and still haven't found any clear or concise info to tell me how I would go about creating this. I have already partitioned the HDD into three sections and have already installed Win7. The active partition is also the boot AND system partition.
I have a Dell laptop which came preinstalled with Windows 7. I wanted to create a new partition and put XP on it to allow me to run a piece of older software. I created the partition and managed to install XP on it as planned. XP runs but unfortunately it hasnt found all the drivers for the ethernet and wireless cards so i cannot connect to the internet.Anyway, now i cant boot from the Windows 7 partition. I have had a look around and things seem to suggest downloading a program to restore the Master boot record-however i cant do this as i cannot connect to the internet in xp. My laptop also did not come with windows 7 disks so i cant restore the MBR in this manner either. Is there anyway i can restore the MBR in my current situation? I dont have another computer so cant download anything elsewhere (currently writing this from ipad). Am i able to delete the xp partition and force windows 7 to load instead? Or can i use the xp cd to somehow access Dos and boot windows 7?
I would like to make my PC dual-boot with Windows 7 Home Premium 64bit version & Linux Ubuntu. I know about Wubi to install Ubuntu within Windows, But would like more space than the 30gb limit that Wubi uses. How do I create an partition with Windows that can be used for a dual-boot. doctorwhovian11-24144041650249291689021989539000 has chosen the best answer to his/her question. Click here to view the answer that was selected.
i cannot boot my Windows 7 64 bit Dell Studio 1558.Cannot boot to Windows.Error(s)BOOTMGR IS MISSING , CTRL + ALT + DEL TO RESTART. Description:
1. Initally had two partitions .. C and D .. 2. Tried to merge C and D to make C more by using Partiton Wizard. 3. Computer Restarted. 4.BSOD at Starting windows logo 5. Stuck at boot. 6. Launched Windows repair. 7. Unable to do repairs. 8. Dell restore unable to locate present installation. ( "current installation : (Unknown) at Unknown drive) 9. Checked partitions using DISKPART at command prompt. 10. Tried to change active partition . Restarted. 11. BOOTMGR MISSING ERROR. Dont even go to startup repair. 12. DVD DRIVE of LAPTOP NOT WORKING so made Windows Startup repair USB bootable. 13. Now have Access to Recovery Menu. 14. Made Partition Wizard Bootable USB . Now have access to Partition Wizard Also. 15. Tried installing Windows 7 using USB. Got error "installation error. verify windows sources are accessible Windows 7 Instalation Problem - Error Code 0xC0000005. 16. Stuck at boot now.
I checked OS drive in partition wizard bootable , it is intact..Windows installation is there....Every drive is ok but somehow booting not from that drive.I will attach photographs of Partition Wizard Partiton status.