Windows 7 Will Not Boot After Partition Resize?
May 1, 2010
I tried resizing my C drive but got an error message. It said something about dynamic discs ??after that when i tried to restart my hp laptop i got this error message:The message on boot states "windows failed to load. A recent hardware or software change may be the cause."The status is "Oxc000000f".The description is "The boot selection failed because a required device is inaccessible"what can i do to fix this problem? i am running check disc like the system suggested, but if it doesn't give me a solution will i need to re install or recover Windows 7 with my back up discs or using HP's system recovery?
View 5 Replies
ADVERTISEMENT
Apr 4, 2012
I recently installed a 90GB Kingston Technology SSD and then created a shadow copy of my previous hard drive (which was 62.4GB), meaning that currently I only have access to this amount of space on the new hard drive.
resize this boot partition to allow me to use all the space currently unallocated?
View 9 Replies
View Related
Jul 17, 2012
I installed a new 1TB drive on my W7 pc. I created 2 partitions but now find I cannot shrink the C partition even when I have turned of system restore. Norton says the C drive has been defragmented and chkdsk reveals no faults. I need some extra space on the other partition for storage which is why I want to shring C where there is plenty of space
View 1 Replies
View Related
Nov 25, 2009
Windows 7 has been released for one month, many computer users have upgraded from old Windows version or installed Windows 7. Yes, new features of Windows 7 are wonderful, but there is a common problem Windows 7 users should pay attention to – partition size.
If you have installed Windows 7, you may find that the system partition free space become lower and lower, as basic Windows 7 installation requirement is 16GB and you have to install many other application. How to solve this problem? Backup all files, delete all partition, recreate partitions, restore? No, what a time-consuming job. Why not resize Windows 7 partition without so much complex works?
If you get ready for Windows 7, you'd better resize the system partition to be large enough and it will solve many problems after you installed Windows 7.
View 6 Replies
View Related
May 16, 2012
I'm using a Thinkpad T420s, dual booting Windows 7 and Fedora 16. However, prior to me installing F16, I used Disk management to shrink the Windows partition. Well...it turns out I shrunk it *way* too small and I'm barely able to use it. Under Disk Management, even if I create unallocated space, it still will not let me re-size my windows partition. I think this is because the partitions are in the wrong order...but I don't know what to do about it.
Disk management shows four partitions as follows from left to right:
| SYSTEM_DRV (1.46 GB, Primary) | Windows7_OS (67.47 GB, Primary, Boot) | (500 MB, Primary) | (76.63 GB, Primary) <--Fedora 16 |
No matter what I do, I cannot click "Extend Volume" on my Windows 7 partition. I would experiment and use certain bootable partition tools, but I'm afraid I'm going to mess with GRUB and I won't be able to boot either one of my OS's..
View 1 Replies
View Related
Nov 10, 2011
I resized a partition (the boot partition) using gparted off a linux boot disk (should be the same as any other program, though) after removing a backup partition which was never used. I rebooted the computer, and it ran startup repair. After startup repair had finished, I rebooted again. This time it boots into windows and gets to the login screen. I can log in, but it comes up with "welcome", followed by "preparing your desktop". It then loads a temporary profile. From there, I tried to load the control panel to load system so I could input the product key, but it wouldn't load the control panel because of an error I can't remember - but it displayed something like this: "{random nums and letters}"how to make it boot from a permenant account?
PS. I have access to command prompt as admin, and regedit. Also, I have another windows partition which I might be able to boot from. I also have a linux bootable CD, if that helps (can move around files from there)
View 9 Replies
View Related
May 22, 2009
I have a dual boot XP/7 system with XP as the first partition, then 35GB of unallocated space, then the 7 partition (don't ask ;-)), then 130GB data partition .. anyway I want to extend the 7 partition back into the unallocated space.. how can I do this..
I'm NOT going to use Acronis having spent 2 days trying to get my hard disk in usable order again .. and I've tried DISKPART but can't seem to get it right.
View 3 Replies
View Related
Apr 14, 2011
So i am running windows 7 and vista on a dual boot Vista hard drive is C: while Windows 7 is B: now i am kinda low on memory on B: and i wanted to re-size so i used "EASEUS Partition Master 6.5.2 Home Edition" and i shrinked C: and had 40gb unallocated space and i went to my C: drive and wanted to resize it but i could't. So i tried out disk management and i had no luck here too. So can any one tell me what i am doing wrong and how i can fix this?
View 4 Replies
View Related
Jan 6, 2011
how to resize partition c as I have not much space left in it and partition d has more space that I hardly use.
Partition c has windows 7 installed in it. how do I make this partition bigger by transfering some space from partition d to partition c?
Is there any reliable free software that I can use to do this? is this possbile or it is risky?
View 9 Replies
View Related
Sep 6, 2009
i read all the topics from here but i am unable to resize my win 7 partition .
i think the problem is that the free space is in the extended partition . how to get the free space from the extended partition without erase or format the other partition (D and E)
http://i31.tinypic.com/2cr3dx1.jpg
I try a lot of programs but no one works becouse the free space is inside the extended partition
View 9 Replies
View Related
May 13, 2009
I am running Windows 7 all great and haven't had any problems, I want to make Windows 7 my sole operating system and remove my XP partition. I managed to install Windows 7 on a separate partition with no problems but just wondering if it's all fine to go ahead and delete my XP partition and then resize my Windows 7 partition back up, this wouldn't create any problems?
Just a matter of backing up all the essentials first, just in case?
View 1 Replies
View Related
May 6, 2011
I have a new notebook and I have used windows bit-locker on the C drive. My notebook didn't come with a TPM chip so I used a work around to get it working by using a flash drive with the keys installed on it, so I just plug the stick in at the boot process for everything to load up successfully. However Ive installed VMware and its taken up a lot of space on drive C.
What I want to do now is allocate some of the free space on the D: drive to the C drive, if that makes sense? Just to clarify my D: drive has no bit-locker encryption on it, but my C: drive does. Want I want to know is can i just use a partition tool to give the C drive some more space or will this cause problems as its using the bit-locker software? Also if I can do this, whats the best partition tool to use.
View 3 Replies
View Related
Nov 22, 2011
I've been trying for a couple days to get my windows seven out of temporary profile mode.ast weekend I downsized a document partition to grow the windows partition by 15gb, using ubuntu's live-cd gParted program. And now I'm stuck with what to do.So far I have tried fixboot, fixmbr, rebuildbcd with no luck. (with windows cd recovery console)I am unable to access any type of administrative tools when i fire up windows (after starting explorer.exe manually). I have a basic windows desktop available to me, but like I said I can't open explorer or control panel, as i get either an error : "explorer.exe No such interface supported"r"::{string of numbers and letters} No such interface supported"Concerning cmd.exe, I can launch it and explore my partitions but everything else seems locked, and I can't run it as administrator.It seems like windows has rearranged its letters too; windows used to be on E: but now finds itself on D:, and the cd drive has gone from D: to E:.Trying to run regedit says that it can't find D:Windows
View 2 Replies
View Related
Jan 11, 2012
They take 20 Gigs of the 120 Gig drive for a recovery partition.A very poor choice on so small a drive. Plus then they use 30 Gigs more for Windows and their included features / bloatware. So there is only 70 Gigs left for programs and storage. Not the user experience that I think Samsung wants me to have. Enough of the rant.How do I get rid of this or resize the 20 gig recovery partition? I don't mind 1-200 Megs for a recovery partition and I think that I want the recovery feature, but 20 Gigs is way too much. I don't mind having Windows on an external disk, but I don't want it taking up a lot of valuable storage on the computer
View 14 Replies
View Related
Dec 19, 2012
I'm building a new computer. Can I partition the hard disk, copy my laptop HD to boot from one partition and run a new windows 7 pro os from the second partition?
View 5 Replies
View Related
Aug 29, 2012
I'm a long-time reader but new poster. I am currently running Windows 7. I want to install Windows XP onto another disc and have a dual-boot setup. I keep Windows 7 up to date and secure, but for the XP partition, I would rather not have antivirus running or even installed, in order to limit background processes. I will not be logging into any place or making any credit card purchases when booted into Windows XP. It will just be used for surfing, games, etc. Further, if and when XP becomes compromised or buggy, I will simply overwrite the partition with a backup image.
If I use Bitlocker to lock down the Windows 7 partition (with the encryption key on a thumb drive) and boot into Windows XP, am I correct in thinking the XP installation see or can't access the Windows 7 partition? If XP gets compromised, can a virus access or write to the Windows 7 partition?
Is there any other reason why this would not be secure? Can a virus write to the BIOS?
View 4 Replies
View Related
Dec 25, 2012
this is what I did, since I have no CD-ROM, to install Windows 7 I created a partion X: NTFS and set it as the ACTIVE ONE, the put there the Windows 7 installation files, and opened prompt command to type bootsect.exe /n60 X: , next I restarted my computer, and automatically it booted into the Windows 7 setup, I installed Windows 7 on the partition C: and formatted the partition C:, everything installed and after the installation finished, a multiple choice menu appears that reads:[CODE]
View 6 Replies
View Related
Dec 18, 2012
I have Windows 7 ultimate 64-bit installed on DELL desktop (Optiplex 990) i7 Core. I have two HDD: Disk 0 contains the operating system 500GB. and Disk 1 empty 1TB.
I want to make a partition on disk 1 to mirror the operating system partition and keep the remaining for data storage. I tried to do but I had the following error message: "All disks holding extents for a given volume must have the same sector size, and the sector size must be valid."
I tried to attach a screen shot but couldn't.
View 5 Replies
View Related
Aug 23, 2012
I have a Boot Camped Mac Mini with Windows 7. I recently needed to allocate more disk space to it as i only had a gig left, i booted into MacOS and used Disk Utility to make the Mac partition smaller, i rebooted into windows and downloaded software called 'Partition Wizard' from www.partitionwizard.com. I dragged the Windows partition all the way so that it used up all the Unallocated Space, it required a reboot to finsih and when it did it displayed an error such as thistatus:0xc0000255Info: The Windows Boot Configuration Data file is missing required informationI have the Installation Disk and i have tried repairing more than 3 times and it seemed to do nothing, so i tried using the CMD and bootrec.exe and now when i start the repair wizard it says there is no windows partition yet i can still try repairing things (Yet still does not repair anything). I downloaded EasyBCD but im on my Mac partition right now and its an exe, i have no clue how to run that within windows to try and repair the Bootloader. I do however have access to the BOOTCAMP partition through the mac side, and i can access all the files. Is there some way i can repair the bootloader through this?
View 6 Replies
View Related
May 24, 2011
I currently have Windows 7 64 bit installed in two partiions:C: drive and E drive. Everytime I start, windows from the C: partition automatically boots. How do I get the Windows from E drive to boot? Ultimately I'd like to use the windows from E drive (which has all my installed software) and delete the one from C: drive. The problem is that I installed the one on C: drive most recently. (Long story short, I tried to delete and old version of windows unsuccessfully, and had to unmount and reformat the partition.)When I go to System Configuration under the Boot tab, I only see Windows in one partition (C: drive), so it won't allow me to delete that.
View 2 Replies
View Related
Jun 21, 2012
I normally run Windows 7. Today I decided to try out Windows 8 as well. I went into Disk manager and created a partition. I then booted off of my Windows 8 DVD and installed it on that partition. Now, my computer is only booting into Windows 8. What I really want is an option to choose which OS to boot into, but I would really like to be able to get back to Windows 7.
View 3 Replies
View Related
Oct 21, 2009
Last night i completed my installation of Windows 7, on new Harddrive.
The disk is partioned in 3 partitions (C,D,E)
C = WinXP
D = Windows 7
E = Data
I started with Windows 7 installation (on partition D). Last night it was completed.
I then format my partition C: and now I can't boot up to Windows 7.
My installation is on a USB.
What can i do??
View 9 Replies
View Related
Oct 1, 2012
I installed Windows 7 on my second hard drive g: (1st partition drive 1) and Windows set up a dual boot with Windows XP on the C: drive (1st partition drive 0) and Windows 7 on the G: drive (1st partition drive 1). Everything worked fine for months until I decided to dump Windows XP to try out Windows 8. I created an Win 8 installation USB FOB. I deleted the old XP Partition on C: then the install failed and I could not boot, (c: was deleted).No problem (I thought), I just swapped the hard drives to boot off my Windows 7 partition. Surprise! It won't boot either. I tried using partition Wizard to repair the MBR, from another computer. That didn't workThen I created a Windows 7 installation USB FOB (no CD drive on target computer), to see if Windows repair would take care of the problem. It could find no Windows installation. So I selected start up repair, it ran for a few minutes then said it was going to reboot, so I pressed the finish button.[CODE]
View 2 Replies
View Related
Aug 24, 2011
Is is possible to make Windows 7 superber tinier, I know how to make it by "use small icons" from taskbar properties, but it is not what I want,, because in that case I am loosing the date from beneath the clock! I want it make a little bit smiler and still keep the Date>
View 4 Replies
View Related
Oct 9, 2011
I downloaded a portable tweaking app from here and the window opens larger than my display so that the bottom of the window (where the buttons to "apply" the tweaks are) is off the screen. The maximize button is grayed out and no moving handles appear when I move the cursor to the window borders. I cannot find a way to maximize the window or resize it.
View 2 Replies
View Related
Jul 29, 2011
My screen when I'm on the web is now really small font and the page obscures the tabs at the top.I clicked on Full Screen accidentally and now I can't see any of the tool bars or tabs.......
View 1 Replies
View Related
Nov 12, 2009
This tutorial describes how to install Windows XP and Windows 7 on the same partition (first tutorial for one partition written).The short concept: Install XP twice and have 7 replace the first installation.Need more testers to confirm it works for everyone and the instructions are clear enough.Requirements: Both Installation discsA Windows XP LiveCD (might work with other OS, but no guarantees)EasyBCD.Install Windows XP normally if you're not already running it.Don't bother installing any drivers or software on it.Start another installation of Windows XP. Choose the same hard drive and leave it unchanged without formatting. When it asks you what to do then choose to install in a different directory "C:Windows.xp".Finish installing that one and only the necessary drivers.afterwards.Install Windows 7 on C: over the regular C:windows. A warning will tell you that it will move the old files to "Windows.old" directory. The good thing is it doesn't touch the Windows.xp directory.Install and run EasyBCD. Go to "Add/Remove Entries" and add an entry of "Windows NT/2k/XP/2k3" type and a name of your choice. (as shown in the attached image)Don't forget the "Save" button.You may also want to adjust the loader timeout from "Change Settings".In C: you will find a (hidden) file "boot.saved". Open it, remove the entry to the "WINDOWS" directory and make the "WINDOWS.XP" your default one (if it's not) and save as boot.ini".Restart and boot from the Windows XP LiveCD (which you should have burned and tested on CD or DVD before starting).Open the Command Prompt (Run "cmd") and enter the following lines in order
[code]...
View 9 Replies
View Related
Jan 10, 2012
I installed Win7 on the same Partition as WinXP. I was in a hurry and forgot totally to partition the HD before I installed, was doing 100 things on the side during the Installation, and noticed my mistake only after the install was complete. Is there any way I can do a Multi boot for those two OS now? The WinXP folder has been renamed to Windows.old, and even with EasyBCD there's no way I can get the Comp to boot into WinXP.
View 2 Replies
View Related
Sep 19, 2012
So long story short, my current os (w7) is installed on a non-boot partition of a now internal drive that used to be external. This wasn't an issue/I didn't notice because I had another unused internal hdd which DID have an old bootable os partition, and then I'd just choose the correct instance of Windows when that one booted.I have to get rid of the old HDD with the bootable partition. Is there anyway I can change the non bootable my currant OS is on to a bootable partition (ie thru windows, cmd, bios etc)
View 7 Replies
View Related
Jan 8, 2013
My Old HDD crashed, it had windows 7 x64 on a D: logical drive with an extended partition. My old HDD also had two other primary partitions one of which probably had some system/boot files etc,. I do not have a backup of these two primary partitions, however, I do have a paragon backup of my logical drive D: extended partition. I got me a new HDD, created a new NTFS primary partition with a drive letter C:. I then restoed the paragon backup of my windows D: drive on to this new primary C: partition. Now, I am not able to boot windows 7. Seems like I need to create a new system partition with boot files to be able to boot my Win 7.
View 7 Replies
View Related
Sep 7, 2011
Is there a way to install Windows 7 in a different folder than the default Windows and on a different partition than the boot. For example, I have XP installed on my Laptop that has 3 partitions C:, D:, E:. C: is my boot partition and D: is where I have XP install in directory D:OSWINXP and E: where applications are installed and data is store.
I like to install Windows 7 and have C: as the boot drive and install it on D: in the sub directory D:OSWindows or D:OSWindows 7.
View 3 Replies
View Related
