[INSTALL] Booting From Restored System Image Fails?
Jan 22, 2011
My Win7 HP x64 PC has two hard drives, each partitioned into two volumes:
My C: and E: drives are each half of a 200GB drive, both NTFS.
My D: and F: drives are each half of a newer, 1TB drive, both NTFS.
My F: drive has around 400GB of 'stuff' that I want to preserve.
I've been trying to migrate the win7 installation from C: to the first partition of the 1TB drive with two different tools (Norton Ghost and the built-in Windows backup utility) and both fail identically.The backup procedure itself appears to work in both cases.Restoring the backup to the first partition of the 1TB drive "works" in so much as I don't get any errors either way.Creating the requisite boot structures also work, as the O/S appears to be bootable.However, when the restored O/S makes it to the login screen, two flaws are evident:
1. The keyboard absolutely does not work.
2. If I log in on an account that doesn't need a keyboard (no password), I see "Loading desktop", then a few seconds "Logging out" and I'm back at the login screen.
If I look at the event viewer logs (booting up with the O/S on the smaller drive), I see numerous events like this:"The AVGIDSAgent service failed to start due to the following error: The system cannot find the file specified.""The Windows Live ID Sign-in Assistant service failed to start due to the following error: The system cannot find the file specified."
I just installed a new hard drive after my previous one failed to start up. I have a backup image stored on an external WD Passport. The install went well. I turn on my tower with the Windows 7 recovery disc in, start up System Image Restore and plug in my Passport. The system restore recognizes my Passport and when I go through the wizard to reformat and partition the disk to match the layout of the recovery image, I get an error message saying "The system image restore failed. No disk that can be used for recovering the system disk can be found. *hyperlink* Details."Details states, "No disck that can be used for recovering the system disk can be found. Try the following: 1) A probable system disk may have been excluded by mistake. a. Review the list of disks that you have excluded from the recovery for a likely disk. b. Type LIST DISK command in the DISKPART command interpreter. The probable system disk is usually the first disk listed. c. If possible,, remove the disk from the exclusion list and then retry the recovery.Tried that, my disk is not listed as an exclusion.2) A USB disk may have been assigned as a system disk. a. Detach all USB disks from the computer. b. Reboot into Windows Recovery Environment then reattach USB disks and retry the recovery.
I created a system image on an AHCI system, then I replaced the hard drives & re-imaged the system. Now Windows won't boot in AHCI mode, it has to be it IDE mode. Why is it not booting in AHCI mode?
I want to create a system image on my NTFS formatted portable WesternD HDD. Now It has about 250GB of space left(the portable HDD), and the Laptop PC that i want to create the image of, tells me I need about 199GB for the system image.Then first time I created the image, it gave me a failure message saying I should run a CHKDSK /R and ty again. I ran a CHKDSK /R on the external drive and tried making a system image again, where it got about halfway and gave me the same message. What is going wrong every time?
I'm trying to repair my Windows 7 ultimate installation. When the procedure reaches its final step, I keep getting a message that the repair failed and that my system is being restored to its former state.Is there a way to depict the cause of this failure? Does Windows 7 keep a log? Is it accessible?Do you know of any other method to overcome this obstacle?
I periodically create a disk image of a RAID 1 Volume consisting of two 500 GB SATA drive containing my Windows 7 system and data, and a RAID 0 Volume consisting of of three 320 GB SATA drives containing my Windows Vista. I tried to do a recovery from the disk image, but my VISTA volume does not restore. Is there anyway to restore both volumes? The recovery indicates the both volumes are to be restored, both only the Windows 7 volume is restored.
After restoring an image made with Clonezilla that used to work, Windows 7 is unable to start. When prompted, I used the DVD, but it still fails with "Startup Repair could not detect a problem".When rebooting, it says "Windows Error Recovery: Launch Startup Repair (recommended) and Start Windows Normally": Launch Startup Repair fails with "Windows Boot Manager: 0xc000000e The Boot selection failed because a required device is inaccessible".FWIW, to investigate, I deleted both partitions (#1 to hold the OS, #2 to hold images) and re-created them with enough space to hold (#1 was made a bit bigger because I didn't know how to specify infos in cfdisk accurately), and Clonezilla happily restored the image.
I am installing Windows on my new SSD. I made the disk GPT (instead of MBR), and installed Windows (tried 5 times now) with similar results. Either error 0xc0000225 or boot loop of "Windows is loading files" ... or it throws me back to my BIOS Boot selection screen where I came from ... what might be the problem? Windows 7 still cant handle GPT partitions? Or it doesnt like the new SSD? I managed to install and reboot successfully once by removing all other drives (except the SSD which I am installing into), works, I can enter Windows. Then once I installed back the other HDDs, it fails again ...
tell me if a re-install from a system image file on my notebook is as good as a clean install from say a retail disk.I can not format all my drive and start a fresh. Can my System image file become glitchy or infected with a virus.?
I am performing a clean install of Windows 7 64bit Home Premium with SP1 integrated on a Dell Studio XPS 8100, and after the first reboot during installation, I get a message "Windows could not configure one or more system components. Windows installation cannot proceed. To install Windows, click "OK" to restart the computer, and then restart the installation." This is a 64 bit machine. Was running Windows 7 64bit Ultimate until yesterday.
Tried partitioning/cleaning/wiping the drives in so many ways I couldn't even count, including "clean all" from repair disk, booting to ubuntu live cd and making sure no rogue filesystems/partitions exist, letting windows installer create partitions, precreating the partitions in diskpart/ubuntu. Have tried several iso's and several cd's/usb drives.
Messed with some bios settings, but to no avail, and made sure my bios was up to date. Downloaded drivers from dell and loaded chipset drivers pre-installation just in case. Have removed all extraneous devices from system excepting the keyboard, mouse, HD, CD-drive, and video card. The 32bit version of Windows 7 Home Premium installed completely fine, with no issues whatsoever, even without pre-loading the chipset drivers.
System Specs: i7 870k 8GB 1333-MHz DDR3 Intel H57 Chipset Two regular old 7200 Western Digital drives GH50N CD-DVD Drive GTX 560ti
My laptop died but the HDD was okay. I've taken the laptop HDD out, bought an USB/caddy for it and attached it to another laptop as an external drive.The trouble is the new machine sees the external drive, but all its seeing is system reserved and the reserved part of the HDD is tiny. So its not the total drive size and defintley not the data I need to rescue. How would I see the whole drive and access the data?
I have a Lenovo B560 with Windows 7 x64. Sequence of events: Played music from a WD external HD with WMP. Music stopped playing and a terrible constant sound is coming out of the speakers (which began a year ago and happens sporadically), no other programs running besides WMP.2. BSOD appeared while the noise kept going, so I held down the power button to turn off the laptop before reading the error message.
Windows 7 32bit on Dell 9200 4 GB RAM 2 x 500GB HDD ... with all OS updates.Been working fine.today left PC running, returned to it, power but screen was 'black'Power off to reboot - on start up (normal) desktop paints in, the spinning wheel runs for ages, then eventually all seems fine but can't do anything, only action is cursor .. nothing clickable. (incl Ctl+alt+del) HDD led on PC running permanently.Reboot in safe mode ... chose system restore .. and it shows a Windows Critical update restore point .. at a time that matches failure.?OK tried restore ... still the same.Tried Windows 7 repair disk, again selected restore ... Tried restore to next previous (2 days ago) all seems to go well, get login, desktop paints in ... then screen goes black ... all that is on it is cursor.
The only other points I can think of is that this morning (last successful boot up) it brought up a pop-up "Express files updated" with recommendation to run it ... as it gave no program, or manufacturer ... I chose not to run.On one of the boot ups during problem .an unfamiliar icon showed on desktop. "Homegroup", a green sphere, surrounded by 3 orbiting blue spheres" although not been there on any subsequent boot up.
i been thinking of upgrading to windows 8 but i might have to go back to windows 7 if things don't' work out as its a possibility.my question is if i return to windows 7 will making a system restore image install all my drivers i need once i go back to windows 7 going back to windows 7 with re-installation DVD
I tried to create a disk image using the Windows 7 feature. The creation failed with a message that chkdsk /r should be run on the source and destination HDs. Destination HD was error free. Source HD had bad clusters replaced in five files.Second attempt to create a disk image failed with the same message.There are no system symptoms, everything seems to be working as usual.
I have a drive that was using PGP that has become damaged and will not boot despite trying 3 days of different fixes and repairs. I have a complete drive backup that will restore but when I try and boot after my PGP password I get 'Missing operating system'. Again I have tried decrypting and fixing but to no end.
I have another disk with a working and booting install of Windows 7 (same architecture etc) on. I have the entire contents of the non-booting system disk that I can access from the image of it.
If I booted into something like Windows Recovery or Live Linux environment, can I copy the entire contents of the non-working Windows 7 drive over the working one and expect it to work and then boot?
for backups of my main OS (in my signature) I have acronis TIH create a single image full backup daily to a different drive. Weekly a single image backup is created and saved on a different drive. Because my SSDs are in RAID0, every few weeks I make a system image backup using Acronis (outside of the daily and weekly backups), clean/all the SSDs to put everything back to 0 on the drives, then restore my installation. It makes a significant performance increase for sure.This last go around a week ago, I did the usual but could not restore no matter what I did. I bought the new version of acronis, the plus pack, unplugged all the other drives, etc etc etc that acronis told me to do to try to fix the error I was getting restoring any backups.Finally what I did was take an old backup, transfer it over the network to a different computer, bought acronis TIH again (ridiculous) and was able to clone it to a drive, plug the drive back into my main rig, boot acronis from a USB drive and clone that installation to the SSD raid setup. The only problem was, the backup I was able to use was from 7-10. I'm now trying to convert the images which would not restore to VHD to boot from the bootmgr screen of the currently restored (7-10) installation.Every tutorial I see only deals with creating a new .vhd to install windows to and boot.
I am trying to make a disk image in Win7 to a partition on my USB HDD.The partition is a freshly formatted 116GB. Win7 says the backup image will require up to 45GB. Yet when the backup process begins, it returns an error message saying there isn't enough disk space for the image.This is apparently a bogus message because I have saved other backup images of this PC to that partition in the past. In fact, I just re-formatted that partition to remove an older image of the same PC (same approx. size image) so I could save the fresh image to it. Can anyone tell me why Win7 insists there's not enough room on a clean 116GB partition for a 45GB image?
While recently using Nero 10's suite of programs I encountered a screen indicating several programs had newer versions and that I should update before continuing. I then updated the programs. The update process required a system reboot to complete the update, since part of the update process could not be completed while the system was running. After clicking on the "Reboot Now Button" the system went through a normal shutdown and start up process. However, after displaying the Windows 7 screen the system hung and I never saw the Windows 7 Logon screen.At this point I powered down and restarted the computer.
The computer displayed the "Windows did not shutdown properly last time" screen during the loading process. I then selected to finish booting in SAFE Mode. The computer then booted successfully and I was able to exercise the system. I then attempted to restart the computer from SAFE MODE but again encountered the "hanging" condition. I again attempted to reboot and once again received the "Windows did not shutdown properly last time" screen. Since booting into SAFE MODE hadn't solved the problem, I attempted to boot into SAFE MODE with networking.This caused the system to again "hang". In summary, I am able to boot into all but the SAFE MODE with networking capability, which reproduces the problem.Since SAFE MODE failed to resolve the issue, I attempted to boot from a Windows 7 Installation DVD. After successfully loading from I selected the "Repair your Computer" option, which then located the Windows 7 system and attempted to repair the error.
After completing the system repair, I again attempted to restart the system, thinking the repair had been successful. However, the computer again "hung" without displaying the Windows Logon screen.I then used an external USB drive containing Fedora 15 to successfully boot the computer. This has allowed me to "poke" around on the hard drive containing the Windows 7 system. I've examined the failing drives partition tables to see if during the updating process the drive had become corrupted. Upon examination of the drive's partition table, I could not find any apparent errors. The following screen shot shows the partition contents of the Windows 7 drive:[CODE]
OS: Windows 7 Home Premium 32 bit The windows system image backed up on my external hard drive (2TB WD USB3) is not showing while restoring the PC from an image.
The only option available is my hard drive partition on which i also had saved a system image. Though windows recommends External hard drive for backing up image when backing up the system.
When i turn my pc on i can see the "Starting windows" screen but i cant see the animation,i just see a little dot. i installed W7 on my sis computer and i can see it ok. i was thinking, the other computer doesn't have a graphics card installed. if it makes a difference?Why i cant get that on my pc?
I have a system that will probably end up loosing power before a proper shutdown more often than not. I need to boot into an image that will allow me to write to a SATA array, remove the array, and install a clean array for the next power up. Could this be done with some type of hibernate image(and how) or would I need to figure out how to boot from an ISO image?My main goal is to boot the system with the same settings every time and write data to the SATA array. The array will be removed and cleaned before power is returned. It would be great if there is a way to change a setting if need be and not need to take more than 20 minutes to redo the image.
At the moment I have Win7 installed on my C drive which is a 1.5TB Samsung, it has two partitions 200GB for the OS and programs and the rest for storage.I bought a Momentus XT to replace the OS C: partition. I have tried a few programs to back-up (image) the C drive to a 3rd drive, unplug my C drive then reboot with the Win7 installation disc and run startup repair. Now at this point I get error's saying I can't run the image restore in this environment then it tells me to reboot from the disc, then basically do what I just did. So I'm stuck in a loop regarding the image restore. Secondly I tried to use Acronis disk director suite to clone the C drive to the new XT drive, this completes successfully. I Unplug my C drive, leaving just the XT in, I boot up, I get a boot error and am told to run startup repair via the installation disc which I do, after doing so it boots past the windows sign, then Acronis does some final checks as it's about to show the login screen, I get blue screened for a split second then the computer reboots. I ran startup repair again, the startup repair is stuck on "attempting repairs" for 30+ mins. So my questions are, where am I going wrong with the image restoration. I've tried saving the image backup to the new drive and to a spare drive. It refuses to restore from both these locations. The error message tells me to do what I did in the first place, and when I do it again it's the same result. With directly cloning the drive,I have obvious boot problems, I can only assume this is to do with the OS thinking it's booting from drive C, what I'm confused about is, wouldn't it be labelled as drive C if the 1.5TB drive is unplugged?
So a couple of days ago, my PC started hanging up on a "Please Wait" loading screen in between the "Starting Windows" screen (where the Windows logo forms from coloured orbs) and the user account selection screen. Sometimes I'd leave it half an hour and it still wouldn't load.To start with, I simply gave my PC a hard reboot, and the problem would go away. When this stopped working, I system restored, and then the problem disappeared. This morning however, I performed a system restore from safe mode, and now when I boot my PC, in whatever mode, I get the "Starting Windows" screen, then the PC hangs up on a black screen with only the mouse pointer active.
Using preinstalled Win 7 Home Premium 64bit on an HP 6813w Pavilion. The original hard drive, a Hitachi HDS721010CLA332 1Tb crashed.1) System Recovery discs was made along with a System Recovery with System Image disc.2) A more current System Image was made on an external hard drive.The Hitachi was replaced with the same model. Checked bios to make sure it was installed correctly.Under System Recovery, Image Restore, Select a System Image Backup there is nothing in the table to choose from as far as a source (disc drive or external drive).A) System Recovery (3 discs) has the HP preinstall file folder on the 3rd disc but is not read by the System Recovery program.B) Under System Restore, Image Restore, Advanced, it asks for a network or driver to be installed. That opens up the directory of C: which is the external hard drive. Under WindowsImageBackup the computer name is identified followed by three entries:[CODE]It seems to me the Recovery and System Restore discs are not functional. Am not a technical person but I have taken this as far as I know how at this point.Printed out all the instructions from HP and Microsoft to follow step by step but the failed discs will not allow me to move forward.
After I tried to make a dual boot with Ubuntu and Windows 7 Ultimate (64-bit), Windows now does not boot. I have tried to reinstall and repair the HDD but the disc fails to recognize my HDD (Western Digital Scorpio Black 500 GB). My HDD is Basic, has 3 primary partitions and 1 extended (3 logical). Ubuntu 11.10 can boot fine.
I want to make a recovery disc to reset my entire 4 partition dual boot hard drive back to its current state. the recovery would reset both xp and win 7 which i have dual booting. can i make one single image to do this without it screwing up my boot loaders etc? what should i use? 3rd party software?
Upon booting up my laptop, everything seems fine at first. My desktop loads as does any startup programs as normal for a good few minutes until the startup procedure is finished, then simultaneously any programs I have open fail to respond and after a few more minutes my operating system fails to respond. Between the time of the programs and the operating system failing to respond, I cannot execute any other programs nor can I lauch task manager (CTRL+ALT+DELETE etc.). A while after the operating system fails to respond this error pops up, no doubt as a response to me trying to open task manager:"Failure to display security and shut down options. The logon process was unable to display security and logon options when CTRL+ALT+DELETE was pressed. If the operating system does not respond, press ESC or restart the computer by using the power switch."
All this occurs without fail everytime I boot up as normal.I can boot up my laptop in Safe Mode with success which has allowed me to try a number of things but I am no computer tech so my knowledge is slim to none. These are what I have tried:
1) I have run anti-virus and anti-malware programs which came back clean.
2) I have tried to go back to a system restore point but apparently I have none.
3) I have tried a clean boot up (with only Microsoft start up procedures) but did not help, just made my OS fail to respond almost instantly as my desktop loading instead of after a fair amount of time.
4) I have 'restarted winsock' on a forum suggestion from another post it may be a particular virus and rebooted but this did not help.
5) I have turned off UAC and rebooted incase something was making changes causing Windows to fail to respond from another forum suggestion. This did not help either.
6) Rebooted with last known working configuration option.
I should also point out I have not recently added any hardware or software that could make this occur. However, maybe the last 3 things I did before the problem occured could help explain. Firstly, I ran a full anti-virus scan with AVG which removed a rootkit and deleted something 'malicious'. After that I used AVG PC tuneup to clean the registry, defrag and clear junk files. Lastly, I tried to run Steam which froze on an update and I tried to restart my laptop, which froze on the "Logging off..." screen for ages by which time my laptop battery must have died. After this the problems arose.
I really want to avoid anything which might have to result in my reinstalling Windows 7 as my laptop came with it pre-installed so I do not have a Windows 7 disc or a OS backup.
Laptop:- Sony Vaio VPCEA3M1E, Intel Core i3. OS:- Windows 7 64bit Home Premium
I have tried to restore my system to an earlier state to remedy the faulty uninstallation of a speech recognition programme, which tries to reinstall every time I start the computer. System restore restarts the computer but then tells me the restore process failed, once i am back to my desktop. OS is Windows 7 Home Premium and computer is an Acer Aspire laptop. System partition is encrypted using Truecrpyt.
I have an OLD computer with a 2.4 GHz processor and 1 GB ram, running XP 32 bit. I wanted to upgrade to Windows 7, So I tried to install 32 bit windows 7, knowing my computer couldn't handle 64 bit. However, at the end, it simply told me "Installation Failed" and reverted to XP, with all my files. I tried multiple times, then I tried installing 64 bit windows 7, and surprisingly, it worked. However, it is laggy beyond belief, so I tried installing 32 bit again. Again the installation failed. Now I'm thinking of reverting BACK to XP.
