Creating A System Image In Safe Mode With Windows 7?
Oct 15, 2012
I am attemptin to make a backup image of my hard drive. The new Image will be complied on an external hard. The drive has a 1TB Capacity with 450 Gigs free. I am receiving an error code during the image compilation stating that there is a problem with the I/O device. I ran chkdsk and found no problems. I also switched USB ports just to rule that out. I have used this same external hard drive to image a different laptop with no issues last week. My next approach would be to try this in safe mode. When I am in safe mode, I cannot find the location of the software which windows uses to create the image. I typed the location into the address bar and it pulled up a link in the address bar which took me back to the control panel. Can anyone tell me if this is possible to do in safe mode and if not, what my next step would be. Windows error: The Operation failed due to a device error encountered with either the source or destination. If the source or destination volume is on a disk, run CHKDSK/R on the source or destination volume and then retry the operation. (0x8078012D) Additional Information: The request could not be performed because of an I/O device error (0x8007045D)?
I have 3 identical PCs with 2 partitions: C and D.I created a system image for one PC, C only.But when I restore that system image into the other 2 PCs (using Wind7 DVD), it formats both C and D and restore.The problem is that I have data on D and I don't want it to be formatted. I only want to restore the C image.
My laptop has been backing up once a week fine (except for an error about a missing file that is on the target drive, not the backup drive) for months. In the past few days, it has suddenly failed with repeated attempts to backup, it always stalls at 57% while creating a system image. I've tried a clean boot, same results. I'm backing up to a network drive (USB hard drive attached to the router), 274GB free of 458 total, and the total backup size has been pretty small as no heavy data is kept on the computer.
When i got my 500 gig internal HD, I messed up and the C: partition is too small. I can't move anything else outta the C partition into the much larger D partition. SO now I want to create a system image on my external HD, so I can re-install Win7 Pro, and not use any partitions. WELL, when i try to create a system image on this external, which sez only needs 396 gig,Windows tell me the external doesn't have enuff space for the shadow volume? There is nothing ON this external. Has 434 of 465 gig free. SO why is that NOT enuff space?
After my problems reported elsewhere, I decided to make a system image after I got things working. This was recommended by inference by one of the gurus who responded to my questions.So I got the system up again and I needed to learn about system images. So I hit F1 and read about creating a system image. Clicked here, clicked there, specified by external hard drive and told it to only include my system drive C:. Whir, whir, whir . . .. system image created.Now, I've cleaned the system of any possible Malware, so I want to create a new image of my system drive. So, I click here, click there and specify my external hard drive but NOW it won't let me include only drive C:, it wants to include my data drive, E:. The check box for E: is greyed out so I can't uncheck it.
I just bought all the parts to build a new computer and I'm putting them together right now. Next step is gonna be installing Windows 7 Professional 64-bit and I'd like to make a backup copy of that fresh install, in case something goes wrong in the future or maybe if I just wanna go back to a clean Windows installation after a while.
Currently I'm thinking of using the "Create a system image" option in the Backup and Restore category from the Control Panel, right after I finish the installing Windows. I've read that this tool creates a .VHD backup of the disk where Windows is installed but I have a couple of questions about using this method:
How big is gonna be the resulting backup? If I installed Windows in a 120GB partition is the backup system image gonna be 120GB in size or is just gonna be ~30GB-ish i.e. the size of Windows system files and folders?
If I restore that system image after using the system for a while is it gonna wipe clean the whole partition and reset it to the state it was when I made the image or is it just gonna bring back the files and folders from the backup and leave alone any other files I had put in the partition?
I have a few quick questions regarding System Images...but first, let me give you a little background.
My HP Pavilion dm-4 has a bum hinge, so I'm sending it to HP for them to fix it. They told me that they typically test the computer before sending it back, and thus also perform a complete system recovery (to go back to factory settings). Obviously, they want me to backup my data.
So. It's question time:
1) Can I restore a "System Image" to get my computer back to its current state upon receiving my laptop back from HP? (is a system image just a duplicate of the hard drive?)
2) Are all hard drives capable of creating a System Image, or just some?
3a) Are there any Hard drives you guys recommend?
3b) My C: (local disk) capacity is 441GB (303GB Free) and my D: (RECOVERY) is 23.5GB (3.43GB Free). Does that mean I have to buy a Hard drive that is at least 465GB...or could I get one that's just 160-ish GB
I was creating a system image with Windows built-in utility. It had been running for at least six hours and I think it may have been either finished or very close when my computer shut down due to a BSOD.
Is there any way to find out whether or not the image was finished and created successfully, or if not, is there a way to continue and finish writing the last little bit to salvage the image and have one that would work if I needed it to restore my computer?
The image was writing to an external HDD, and I think it had to erase/write over the previous image due to space considerations.
I am trying to create a system image ready for installing a larger HDD (WD20EARX), but when using the Windows 7 wizard, the drive, Buffalo 500 USB External HDD, is not in the drop down selection box. The drive is there OK and can use it OK for normal work and there is over 450GB available. My original HDD is 160GB.
I want to create a system image on my NTFS formatted portable WesternD HDD. Now It has about 250GB of space left(the portable HDD), and the Laptop PC that i want to create the image of, tells me I need about 199GB for the system image.Then first time I created the image, it gave me a failure message saying I should run a CHKDSK /R and ty again. I ran a CHKDSK /R on the external drive and tried making a system image again, where it got about halfway and gave me the same message. What is going wrong every time?
XPS L401X Base Genuine Windows(R) 7 Home Premium 64bit (English) Intel(R) Core(TM) i7-740QM Processor 6GB 1333MHz DDR3 SDRAM (1 x 2GB + 1 x 4GB) 640GB 7200RPM Hard Drive
Lately whenever i try to start my computer it pass the Dell Bios and then directly goes to the screen which states Repair your system or Start windows normally When i chose repair system , it start downloading windows files and then launch the windows , but hung up at the sky blue login window with only movable cusor . When i choose to start windows normally it gives me BSOD momentarly ( hard to see the message) and then restarts again . i tried with the advanced boot up options like repair my computer , all safe modes , restore to last good configuration but it does the same and hangs at windows loging sky blue window .I Tried to run the Dell PSA+ Diagnostic and it returns with 2000-0146 error . As per the Dell online solutions for this type of error ,I tried to reinstall the Hard disk but the problem still exist.
I have recently installed windows ultimate x64 on my computer.i have an asus p6t deluxe v2 mobo, i7-960 cpu and a wd velociraptor hdd. The install went ok, I even managed to restart my computer a few times after but after windows updates installed it won't boot. I tried to boot into safe mode, restore from the installer, and repair, none worked. After startup repair it says: "a patch is preventing the system from starting" and I get a 0x1f error code.(Preventing windows from downloading any updates didn't work either)
On this recent windows update, 2/14/13, my computer froze on the "Preparing to configure windows" screen for several hours. I rebooted normally and the screen went to "configuring updates" and stuck at 67% for about an hour. I got frustrated with it and rebooted to safe mode to see if I could do a system restore and when I did it said there was no restore point back up! So I rebooted normally and now it is still just sitting on the "Preparing to Configure Windows" screen with the circle spinning. I am using Windows 7 Ultimate on a Dell Dimension 2400.
I created a system image on an AHCI system, then I replaced the hard drives & re-imaged the system. Now Windows won't boot in AHCI mode, it has to be it IDE mode. Why is it not booting in AHCI mode?
I'm currently using a windows 7 computer and am having trouble accessing system restore. As I start up the computer normally, I make it past the login screen to the main screen, and it freezes after a few seconds each time. Going on safe mode instead, I went to system restore only to find that is was turned off as well my network connections
my laptop starts up as the "windows did not shut down properly" screen where I can start windows normal to do repair. When I start windows normally it sends me to the repair screen. And when I select system repair it just freezes at a light blue and geen screen and the only thing showing is my cursor. Ive tried to run the system in safe mode but it freezes at classpnp.sys, and eventually sends me back to the repair screen that is frozen. I don't believe I have my windows 7 installation disk for my laptop so that is out of the equation.
My brother was using my computer and said it was updating when this happened so Im not sure what caused all this.
The other day i found some ram and decided to try and see if it worked in my Dell desktop computer, when i turned it on it said i couldnt mix different types so i took it out and turned it off, i diddnt even go on it.Today i turned it on and it got to the windows 7 logo and it restarted and said windows failed to start, launch startup repair or start normally. I clicked startup repair but it woulnt work, i tried restoring to an earlier date but that wouldnt work either. I tried safe mode but when it gets to loading it restarts and just goes round in circles.
My system is stuck in a boot loop while booting in safe mode,I was updating the drivers on my video card. I used driver cleaner pro to remove my old drivers. I then used msconfig to boot in safe mode with the minimal option selected. When the computer reboots I get to the screen to type in my password for 5 seconds an the computer reboots itself.
After a power outage, my windows 7 will not boot without going into safe mode.How can I restore my system to boot automatically without going into safe mode.
I ran the disk cleanup and it freed up several GB of space on my C drive (I have a Dell laptop with a C drive with about 62 GB of space and a D drive with 426 GB.I let it run overnight because it said it was going to take 6 hours (no idea how long it actually took).
It had either shut down or hibernated, so I turned it back on the next morning. Windows booted up, but has not been working--I can't use the shortcuts, and even if I click on something from the start menu it won't run. (Firefox, for example, or other programs). It gives me an error message about the data not being found with an I/O error.I am able to use the internet and some programs in Safe Mode, which is what I'm doing now.I can't use my audio system in Safe Mode.I have the upgrade CD for Windows 7--they sent it after I had bought the computer. Do I need to reinstall Windows 7?Can I do it from the update CD?Do I need to back up all of my files (photos, etc) before I reinstall it?
After attempting to start my Laptop in Safe Mode, it loaded drivers normally only to crash a few seconds later. A prompt message appears but is impossible to read because Windows immediately reboots upon showing the prompt.
I am familiar with System Restore, selecting earlier times, and the often-available option of undoing a System Restore. But I found out (too late) that according to Microsoft, System Restore done in Safe Mode is not able to be undone.I lost 1,000's of photos doing the system restore, now the only restore point option visible is what I believe to be the new one after I did the restore. Prior to me doing the System Restore, there were a number of times from me to choose from, I just chose one that was 10 days ago. Is there any software, method, or hack that I can use or do to recover the thousands of photos that were on my desktop and that were in folders on my desktop? It's a 1 TB HD?
I work for a company which needs to make small specialized PCs running Windows so they can run a specific program, hopefully on an 8gb CF card. I'm in the process of stripping down a copy of Windows 7 to be small enough for that, but that's something else. I need to be able to install the reduced copy of Windows 7 and our own software and then probably use Norton Ghost to create an image that I can just apply to every one of these computers we make in the future. Is there a way of creating this image from within my main OS instead of just creating and booting to a separate partition?
i just crashed som1 64 bit lennovo laptop while i opperate a 32 bit pc dont have any windows system with me,it wont start on safe mode,and system repair has failed many times.the laptop was running on low battry and it shut itself,when i tryed to reboot it,it automaticly went to system repair which failed
I recently installed an SSD in my laptop and moved the HDD to the secondary drive (I have room for two). I did a few of the prescribed steps for optimal SSD usage (moved user profiles to HDD, moved temp directory and page file, etc). Initially I was able to image only my C drive (about 30GB required). This was when I could still dual boot to my original partition on the HDD.
I've since removed the old Windows 7 install from the HDD and made it a single partition. However, now when I try to make a drive image I'm unable to deselect my HDD when creating an image. I'm given no option except to create an image for both drives with a resulting size of 209GB. I'm already backing up my user data already and don't want to include it in the image.
When I view the disk manager my HDD (drive E) is Disk 0 and my SSD (drive C) is Disk 1. I've run bcdboot c:windows /s c: to ensure I have the boot files on my SSD. I'm able to boot my machine on the SSD if I disconnect my HDD but it doesn' like that my profile isn't available. I've also tried to change the disk order in my laptop BIOS but I don't have the option of changing the order of the individual disks.
What I want to do is be able to do is image only my SSD and not the entire system. I also want to do it on a regular basis and avoid having to open up my laptop and disconnect the HDD.
Is this related to the order of my disks in the disk manager or is that just a red herring? How do I make it so I can only select the SSD when creating a disk image?
I've been placed in charge of setting up new PCs at work.These are tablet PCs and the hardware in each is identical...I've now setup one PC to function EXACTLY how I want it.My question is, what's the best way to image the entire drive and then load it onto subsequent PCs (please nothing like PXE) the restore will be done from a USB thumb drive.
the computer I am concerned with is running Windows 7 with IE8, Microsoft Security Essentials and Malwarebytes Anti-Malware. I am currently in Safe Mode with Networking without issue.The owner of the computer says that something happened earlier today while he was online that sounds like some false antivirus popup, but he's unsure. Here are the symptoms in normal mode. Every application, from moving through them to opening and closing them, runs exceptionally slow - one to three minutes to open, at least a minute to open internet pages. I noticed that, when in IE, as the pages are loading the IE page disappears and reappears. I am not very familiar with Windows 7 so I don't know if it is related. The computer seems to be getting slower as the day goes on. CPU usage is very high.So far, I have disabled many startup items that were unnecessary. I ran CCleaner and cleaned up. MBAM was run in both normal and safe mode, full scans, and found nothing. This is also posted in Viruses and Malware, but I'm unsure where it should live.
window 7 working on safe mode and unable to choose the another restoration point and it is not loading in normal mode -after installed third party software worked on that for few hours, then after switched off and later it switched on then after this problem started, automatic repair done, nothing is notified
I am using acer laptop,intel Pentium processor,windows7 professional os,my problem is windows is not starting normally and is running safe-mode.when entering normal mode it is displaying "welcome" after entering password "Please wait",it takes a long time to starting window and i'm waiting more than 24 hours but its not starting window normally...but it starting safe mode.