I have 3 identical PCs with 2 partitions: C and D.I created a system image for one PC, C only.But when I restore that system image into the other 2 PCs (using Wind7 DVD), it formats both C and D and restore.The problem is that I have data on D and I don't want it to be formatted. I only want to restore the C image.
View 9 Replies
I'm about to install my new 256gb SSD. This will have 3 partitions;
100mb System reserved partition
80gb Windows OS partition
The rest will be used for VHDs
So, using disk part.. are these the correct commands in the correct sequence (Having unplugged my spinners first so diskpart only sees one drive
select disk 0
clean
create partition primary size=100 align=1024
create partition primary size=80000
select partition 1
format quick fs=ntfs
active
exit
Should I also be formatting the S/R partition? I will create the final partition via disk management when windows is installed. This will result in 3 partitions, all properly aligned etc. Yes? Or am I on some far off planet?
I am attemptin to make a backup image of my hard drive. The new Image will be complied on an external hard. The drive has a 1TB Capacity with 450 Gigs free. I am receiving an error code during the image compilation stating that there is a problem with the I/O device. I ran chkdsk and found no problems. I also switched USB ports just to rule that out. I have used this same external hard drive to image a different laptop with no issues last week. My next approach would be to try this in safe mode. When I am in safe mode, I cannot find the location of the software which windows uses to create the image. I typed the location into the address bar and it pulled up a link in the address bar which took me back to the control panel. Can anyone tell me if this is possible to do in safe mode and if not, what my next step would be. Windows error: The Operation failed due to a device error encountered with either the source or destination. If the source or destination volume is on a disk, run CHKDSK/R on the source or destination volume and then retry the operation. (0x8078012D) Additional Information: The request could not be performed because of an I/O device error (0x8007045D)?
View 2 Replies View RelatedMy laptop has been backing up once a week fine (except for an error about a missing file that is on the target drive, not the backup drive) for months. In the past few days, it has suddenly failed with repeated attempts to backup, it always stalls at 57% while creating a system image. I've tried a clean boot, same results. I'm backing up to a network drive (USB hard drive attached to the router), 274GB free of 458 total, and the total backup size has been pretty small as no heavy data is kept on the computer.
Lenovo SL510
Windows 7 Professional
When i got my 500 gig internal HD, I messed up and the C: partition is too small. I can't move anything else outta the C partition into the much larger D partition. SO now I want to create a system image on my external HD, so I can re-install Win7 Pro, and not use any partitions. WELL, when i try to create a system image on this external, which sez only needs 396 gig,Windows tell me the external doesn't have enuff space for the shadow volume? There is nothing ON this external. Has 434 of 465 gig free. SO why is that NOT enuff space?
View 2 Replies View RelatedAfter my problems reported elsewhere, I decided to make a system image after I got things working. This was recommended by inference by one of the gurus who responded to my questions.So I got the system up again and I needed to learn about system images. So I hit F1 and read about creating a system image. Clicked here, clicked there, specified by external hard drive and told it to only include my system drive C:. Whir, whir, whir . . .. system image created.Now, I've cleaned the system of any possible Malware, so I want to create a new image of my system drive. So, I click here, click there and specify my external hard drive but NOW it won't let me include only drive C:, it wants to include my data drive, E:. The check box for E: is greyed out so I can't uncheck it.
View 8 Replies View RelatedI just bought all the parts to build a new computer and I'm putting them together right now. Next step is gonna be installing Windows 7 Professional 64-bit and I'd like to make a backup copy of that fresh install, in case something goes wrong in the future or maybe if I just wanna go back to a clean Windows installation after a while.
Currently I'm thinking of using the "Create a system image" option in the Backup and Restore category from the Control Panel, right after I finish the installing Windows. I've read that this tool creates a .VHD backup of the disk where Windows is installed but I have a couple of questions about using this method:
How big is gonna be the resulting backup? If I installed Windows in a 120GB partition is the backup system image gonna be 120GB in size or is just gonna be ~30GB-ish i.e. the size of Windows system files and folders?
If I restore that system image after using the system for a while is it gonna wipe clean the whole partition and reset it to the state it was when I made the image or is it just gonna bring back the files and folders from the backup and leave alone any other files I had put in the partition?
I have a few quick questions regarding System Images...but first, let me give you a little background.
My HP Pavilion dm-4 has a bum hinge, so I'm sending it to HP for them to fix it. They told me that they typically test the computer before sending it back, and thus also perform a complete system recovery (to go back to factory settings). Obviously, they want me to backup my data.
So. It's question time:
1) Can I restore a "System Image" to get my computer back to its current state upon receiving my laptop back from HP? (is a system image just a duplicate of the hard drive?)
2) Are all hard drives capable of creating a System Image, or just some?
3a) Are there any Hard drives you guys recommend?
3b) My C: (local disk) capacity is 441GB (303GB Free) and my D: (RECOVERY) is 23.5GB (3.43GB Free). Does that mean I have to buy a Hard drive that is at least 465GB...or could I get one that's just 160-ish GB
I was creating a system image with Windows built-in utility. It had been running for at least six hours and I think it may have been either finished or very close when my computer shut down due to a BSOD.
Is there any way to find out whether or not the image was finished and created successfully, or if not, is there a way to continue and finish writing the last little bit to salvage the image and have one that would work if I needed it to restore my computer?
The image was writing to an external HDD, and I think it had to erase/write over the previous image due to space considerations.
I'm creating a system image on my laptop. Is it safe to use my computer while creating a system image?
View 5 Replies View RelatedI am trying to create a system image ready for installing a larger HDD (WD20EARX), but when using the Windows 7 wizard, the drive, Buffalo 500 USB External HDD, is not in the drop down selection box. The drive is there OK and can use it OK for normal work and there is over 450GB available. My original HDD is 160GB.
View 3 Replies View RelatedI want to create a system image on my NTFS formatted portable WesternD HDD. Now It has about 250GB of space left(the portable HDD), and the Laptop PC that i want to create the image of, tells me I need about 199GB for the system image.Then first time I created the image, it gave me a failure message saying I should run a CHKDSK /R and ty again. I ran a CHKDSK /R on the external drive and tried making a system image again, where it got about halfway and gave me the same message. What is going wrong every time?
View 4 Replies View Relateddue to some personal issues i need to completely reformat the whole HD.. and for some reason when i try to do it it only lets me format windows partition and i want EVERYTHING to be gone.
View 7 Replies View RelatedIf you create 2 partitions on a hard drive and copy a LARGE file from one partition to the other the copy is very slow with lots of head movement.I wonder if there is the same overhead/concept with an SSD?Yes I do realise an SSD is memory but I want to know if you partition an SSD and copy from one partition to the other is there a corresponding degradation? Considering interface turn around etc?Or, in other words, if you copy from one partition of an SSD to another partition on the same SSD will it be as fast as copying from one SSD to another completely separate identical SSD?
View 5 Replies View RelatedI recently installed a fresh copy of Windows on my SSD. During setup I opted to delete all my old partitions on the drive, however I did not format the drive. Will this decision have an impact on the performance of the drive? Should I have reformatted the unallocated space on the drive to get better performance?
View 4 Replies View RelatedI work for a company which needs to make small specialized PCs running Windows so they can run a specific program, hopefully on an 8gb CF card. I'm in the process of stripping down a copy of Windows 7 to be small enough for that, but that's something else. I need to be able to install the reduced copy of Windows 7 and our own software and then probably use Norton Ghost to create an image that I can just apply to every one of these computers we make in the future. Is there a way of creating this image from within my main OS instead of just creating and booting to a separate partition?
View 5 Replies View RelatedI recently installed an SSD in my laptop and moved the HDD to the secondary drive (I have room for two). I did a few of the prescribed steps for optimal SSD usage (moved user profiles to HDD, moved temp directory and page file, etc). Initially I was able to image only my C drive (about 30GB required). This was when I could still dual boot to my original partition on the HDD.
I've since removed the old Windows 7 install from the HDD and made it a single partition. However, now when I try to make a drive image I'm unable to deselect my HDD when creating an image. I'm given no option except to create an image for both drives with a resulting size of 209GB. I'm already backing up my user data already and don't want to include it in the image.
When I view the disk manager my HDD (drive E) is Disk 0 and my SSD (drive C) is Disk 1. I've run bcdboot c:windows /s c: to ensure I have the boot files on my SSD. I'm able to boot my machine on the SSD if I disconnect my HDD but it doesn' like that my profile isn't available. I've also tried to change the disk order in my laptop BIOS but I don't have the option of changing the order of the individual disks.
What I want to do is be able to do is image only my SSD and not the entire system. I also want to do it on a regular basis and avoid having to open up my laptop and disconnect the HDD.
Is this related to the order of my disks in the disk manager or is that just a red herring? How do I make it so I can only select the SSD when creating a disk image?
I've been placed in charge of setting up new PCs at work.These are tablet PCs and the hardware in each is identical...I've now setup one PC to function EXACTLY how I want it.My question is, what's the best way to image the entire drive and then load it onto subsequent PCs (please nothing like PXE) the restore will be done from a USB thumb drive.
View 9 Replies View RelatedI was trying to make an system image of my Win 7 OS to my hard drive...all went well until it finally stopped with the following message: backup failed! System could not find file specified ( 0x80070002 ) close. Nothing else...how is one suppose to make sense of this? Does this mean i can never make an image file of my system? Prior to the backup, Win 7 said that it would check system to make sure its OK to make backup. After it did the checkup it gave me the go ahead to do it
View 3 Replies View RelatedOur small office has several laptops, some with Intel chips, some with AMD. I'm trying to find a way to create an image for each laptop type that would include Windows 7 and MS Office.
I've looked around a bit, and I'm finding plenty of info on creating the Windows 7 image, but can't really find anything in layman terms for also including MS Office and any other necessary programs (snagit, Adobe Reader, etc.) to include or how to include, in the image.
Obviously, free (shareware) software is good to do the job in order to keep the cost down. I think I might even have a copy of WinPE I inherited from the person that was there before me, unfortunately, no documentation....Like I said, I've never done this before and I could use a step-by-moron-proof-step process if one actually exists...
I am replacing my HHD with a SSD and made a mirror image on my backup external drive. When I tried to do the system image recovery, it fails to find the recovery information. It says the no disk that can be used for recovering the system disk can be found.
View 6 Replies View RelatedI have a workstation on a gaming rig. I work and play games on it. I wanted to ask if I could separate my work files and GAMES setups (installed files) so they don't harm my work data.I do play games with cheats/hacks and they mostly contain malicious files which can damage my operating system. I want to create a seperate DISK image like Vmware in which I can run games without being worried about any harmful files accessing my work partition.
View 5 Replies View RelatedOS: Windows 7 Home Premium 32 bit The windows system image backed up on my external hard drive (2TB WD USB3) is not showing while restoring the PC from an image.
The only option available is my hard drive partition on which i also had saved a system image. Though windows recommends External hard drive for backing up image when backing up the system.
I have an HP laptop with Windows 7 home premium. When using the HP Recovery manager to create system restore disks, everythong goes ok until I get through the point where it tells me that I will need 4 DVDs and that I should insert one. After inserting the disk, the drive spins for a coouple of seconds, then I get the messages:"There was a problem burning this disk.""There was an error burning this disk. The disk might no longer be usable."I retried several times, inserting different blank DVD-R disks, but always get the same result
View 6 Replies View RelatedI'm trying to reload a windows xp sp3 system with 5 partitions. root partition (c:) has bcdedit.exe and store. z: is application store with bunch of batch scripts.A web application is hosted in Apache omcat on c:. One of the cgi script in web application calls a batch file on z: drive with following command.
BCDEDIT.exe /store c:ootcd ootsequence {UUID}
I'm getting following error
The boot configuration data tore could not be opened. A required privilege is not held by the client.
I do not see error, if command is run from command prompt with admin privilege. my web app is running under admin privileges.
I have one HDD C: with Windows 7 64bit and another HDD from my previous dual boot PC with two partitions C: and E:, both winX pro.How is it possible to combine both HDDs, creating a multi boot system having as C: my Windows 7 drive?
View 2 Replies View RelatedSo basically, I decided that I would get windows 7 and get a new hard disk to install it on, as my original is getting a little on the old side.
Installing the new hard disk was smooth, as was formatting it and installing windows 7 on it. However, I foolishly forgot to unplug (C:) which is the disk with Vista on it (which is the only other OS). This of course is the system disk, and so my Windows 7 disk (M:) is now reliant upon it to boot. This means I cannot format (C:).... I tried repairing the windows 7 installation (without (C:) plugged in) using the windows 7 disk, however it just told me what I already knew, and didn't repair it.
Is there anyway I can make (M:) a system disk, and therefore format (C:)? (Preferably without having to reinstall Windows 7)
On my system I have an SSD, so I have (Windows Restore) turned off. When I download a program and try to install it, it says creating a Restore Point and sits there for a while. A long while. I have found that I can go into Safe Mode and install things with no problem, fast. Even after it is satisfied with the restore point and says it is installing, it will just sit there and drag on. What can I do to get things to install without Safe Mode?
View 9 Replies View RelatedJust yesterday Windows 7 got infected with some kind of bug that cause it to lag, crashed programs and was apparently capable of piggybacking off USB sticks- as my eeePC could tell you. I've reinstalled a new copy of Windows 7 on a different partition of the same HDD but now I can't seem to format the old partition in either Windows Disk Management or EASEUS Partition Master. I checked the status of the disk and I think it might be because that partition is classed as Primary or System or something.
Does anybody have any programs or advice that can help?
If I purchase the RETAIL Windows 7 Upgrade:
1. On a system with Windows XP, can I install the upgrade into a 2nd partition to create a multiboot Windows XP/Windows 7 system? I do have retail Windows XP Pro media full version.
2. On a system with Vista, can I install the upgrade into a 2nd partition to create a multiboot Vista/Windows 7 system? I do not have Vista on media, it was pre-installed on the system.
3. On a notebook computer running Vista, should I choose to do so, could I install Windows 7 over Vista? Might I get into trouble due to proprietary notebook drivers?
4. On a notebook computer running Vista, should I choose to do so, could I uninstall Vista and then install the Windows 7 upgrade? Might I get into trouble due to proprietary notebook drivers? Also, since I do not have Vista on media, how would I prove that I qualify for the Windows 7 Upgrade?
just setting up a friends new dell laptop create system disks - no mention in the manual how to
s511016au dell inspiron 1545 laptop.
it only came with software application disks.
