Can someone hit me with a link for manually installing the AHCI driver and switching the OS mode for the storage controller.
If I remember right, this is just putting the driver in /sys/drivers, running a script, and making a registry change. Then you reboot, change the motherboard setting, and then install IMSM after the OS comes back up. I don't remember the script, or if it was just a reg edit, etc.
I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.
View 1 Replies View RelatedIm installing a new SSD and i wanted to use it as an oppertunity to change everything over to AHCI and wanted to clarify one thing before i went ahead. Im going to change the setting to AHCI in the bios and then install windows 7 on the SSD. Once i get into windows i was going to plug in the old Hard drives. With the old hard drives being used when my computer was on IDE will they be able to be read or will all the data be lost.
View 1 Replies View RelatedWhen I start up my pc I my screen stops at the POST screen where down to the bottom it says AHCI Port 0 error...I never had that error before as normally I won't even see the POST screen.
View 14 Replies View RelatedI Installed Windows 7 on my Toshiba P205-S8810 and I see in the device manager 2 missing drivers :
- Mass Storage Controller.
- Multimedia Controller.
I checked Toshiba website but there are a lot of drivers.
I installed Windows 7 on my SOLID 2 Series SSD with it only plugged in during install. I latter added a 1tb Spinpoint F3 hard drive, and velociraptor for programsDespite the bios is in ACHI mode and it says ACHI controller installed I get these two things popping up.Is this normal? Can I change it to ACHI from installing drivers[CODE]
View 3 Replies View Relatedanyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
I have tried installing & uninstalling xp mode and vm 4 times with new downloads again and again to no avail. i have tried to install xp mode first and get the error 2203...I have installed vm first and then xp mode with the same result. Error 2203 on the web seems to be related to an installer problem yet I have installed many programs with no errors at all.
View 1 Replies View RelatedI am looking for these drivers. I have a Sony Vaio desktop that I upgraded from Vista 32bit to Windows 7 64bit. The model is VGC-LT32E.
View 7 Replies View RelatedI need to reinstall my Windows 7 Ultimate 32 bit O/S if I wish to use the AHCI setting for SATA disks?I installed the O/S with the BIOS setting for SATA at ATA then changed it in the BIOS after install. Unfortunately, the PC will not boot with it set to AHCI for SATA but changing it back to ATA gets it to boot.I thought that from Vista onwards the SATA setting in the BIOS could be changed after the O/S had been installed, perhaps not ?
View 1 Replies View RelatedEverytime i want to swap hard disk with different OS, WinXp(IDE) to Windows 7(AHCI), i need to do change some hard disk setting on BIOS. Is there any way that i can do to make both hard disk with different OS compatible on the desktop PC without change any setting on BIOS everytime i change hdd? Is there a way to make WinXP IDE mode to run under AHCI mode?
View 1 Replies View RelatedDriver update program says new driver available 1.0. Any issues regarding updating this driver. No problems needed. Dell Inspirion laptop Win 7 Home Prem. 64bit 4gb ram
View 7 Replies View RelatedI'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..
View 6 Replies View RelatedFirst thing, my build:
Board: Gigabyte GA-P55A-UD4
CPU: Core i7 870 @ 2,93 Ghz
Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18
Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD
Running: Windows 7 Ultimate
Trying to install: Windows 7 Ultimate
PSU: LC Power Arkangel 850W
I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally.
I didn't know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the HDD? Anyway, I really want to start using the disk. I have tried installing Windows 7 from a dvd as well as from a USB key.
I changed the appropriate setting in the registry. (msachi > start: 0) Then I changed the setting in my motherboard and Windows froze upon starting up, and my system rebooted.
The thing is, I changed it to AHCI before. It worked fine! I then switched back to IDE while trying to fix a problem with eSATA detection (turned out to be a faulty cord), Now I can't switch back! Sigh. I really would like my eSATA to be plug and play.
First thing, my build: Board: Gigabyte GA-P55A-UD4 CPU: Core i7 870 @ 2,93 Ghz Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18 Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD Running: Windows 7 Ultimate Trying to install: Windows 7 Ultimat PSU: LC Power Arkangel 850W
Ok so here's the deal. I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally. I didnt know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the disk? Note: I have tried installing Windows 7 from a dvd as well as from a USB key.
I am trying to upgrade from Windows Vista 32 bit to Windows 7 32 bit but when booting from the upgrade disk it has problems finding my HDD's and says that windows cannot be installed on them once found.
When choosing a clean install from loading the disk from within Vista it starts to install and then when it restarts it brings up a blue screen saying that windows cannot be installed and is I have installed any new HDD's or controllers then on uninstall them.
When trying to upgrade at first it was complaining about the ATI ACHI Compatable RAID controller not being compatable but now it starts to do the install and then on restart it does the same as the clean install.
my driver updater asked me to update this driver (standard AHCI 1.0 serial ATA controller)..but i cannot do it using the software coz my internet connection is slow.So,i want to download it manually.Where can i get this driver?
View 6 Replies View RelatedI have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.
My question:
SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s.
TDK DVD+R disks tested OK (on other PC) for 16X capability.
Why is Nero reporting of only 2.4X and 4X writting speeds?
I have a W7 64 bit machine and I am trying to update the RAID controller driver without success.I am blocked by W7 from updating the driver and get the "Windows has determined that the best driver is already installed" message.I have tried to work around that and have been unsuccessful.Ultimately I am trying to enable a program "Hard Disk Sentinel" to view and display hard disk SMART info. Unfortunately the RAID driver controlling the HDD's on my PC have a date signature of 2009 and need to be updated to take advantage of SMART information technology
View 3 Replies View Relatedi'm working with a new pc build that uses a 60 gb ssd for its boot drive, and which is also reusing some "old" sata hdds for storage.
at the time i installed windows 7 ult 64, i had only a new ssd plugged in, and the bios was set to ahci mode. the installation went fine and i was able to boot into windows afterwards without issue.
then, i connected a wd caviar black sata hdd to use as storage, with the ssd being the boot drive. with both of them connected, windows will not get past the starting windows screen.
i made this video of the program before i understood that it was a drive controller issue: startup problem - Internet in it, you can see that windows boots fine in ahci mode with just the ssd plugged in, but that when the backup sata drive is also connected it doesn't get past the starting windows screen.
for the record, this caviar black hdd was my previous boot os, and it also has a windows 7 install on it (which i've renamed the base folder of), but it is not booting from that hdd. also, i have tried the same thing with other "old" sata hdds that do not have any previous windows install on them, and the result is the same thing which is shown in the video.
where can i download the mass storage controller for win 7
View 1 Replies View Relatedi am looking 4 mass storage controller driver 4 sony, VGN-NR123E
View 1 Replies View RelatedMass storage controller driver windows 7 free download
View 1 Replies View RelatedMass storage controller driver windows 7?
View 2 Replies View Relatedfind mass storage controller driver for acer extensa 5220.
View 1 Replies View RelatedFor Windows 7 32 bit
AWOOKHBV IDE Controller(Code 39) is missing.
Device Type: Storage controllers
Manufacture: (Standard mass storage controllers)
Location : on Extended IO Bus
I fell asleep with my PC on and woke up with it stuck in sleep mode. I performed a hard shut down via holding down the power button for several seconds. Now the pc will not post and my monitor claims no signal. No beeps from the Mobo speaker. I've replaced my cmos battery so far.Mobo is an asus m3a79-t Deluxe and I've heard some issues of bios not supporting sleep modes?
View 9 Replies View Relatedi have an ASUS M5A88-M motherboard, and a Western Digital WD2503ABYX HDD. i am trying to make that drive work in AHCI mode, but when I try, the disk won't boot. i think the HDD is AHCI compatble, tho not certain. i went into the registry to set a value=o for the relevant AHCI parameter, but no luck. if i need a full re-installation of Windows 7 64-bit, does it prompt me along the way to set the mode to IDE or AHCI?.
View 2 Replies View RelatedI created a system image on an AHCI system, then I replaced the hard drives & re-imaged the system. Now Windows won't boot in AHCI mode, it has to be it IDE mode. Why is it not booting in AHCI mode?
View 5 Replies View RelatedI successfully installed Windows 7 64bit in AHCI mode on a PC with 3 new 3TB Western Digital WD30EZRX Caviar Green hard drives.Then I installed "Intel Matrix Storage Manager Driver [v8.9.0.1023]" & as soon as Windows restarted after installing it, Windows would not boot, & will now only boot in IDE mode.In IDE mode I have to do a system restore to the point before installation of "Intel Matrix Storage Manager Driver" to be able to boot again in AHCI mode.
View 1 Replies View Related