I have a W7 64 bit machine and I am trying to update the RAID controller driver without success.I am blocked by W7 from updating the driver and get the "Windows has determined that the best driver is already installed" message.I have tried to work around that and have been unsuccessful.Ultimately I am trying to enable a program "Hard Disk Sentinel" to view and display hard disk SMART info. Unfortunately the RAID driver controlling the HDD's on my PC have a date signature of 2009 and need to be updated to take advantage of SMART information technology
I am trying to upgrade from Windows Vista 32 bit to Windows 7 32 bit but when booting from the upgrade disk it has problems finding my HDD's and says that windows cannot be installed on them once found.
When choosing a clean install from loading the disk from within Vista it starts to install and then when it restarts it brings up a blue screen saying that windows cannot be installed and is I have installed any new HDD's or controllers then on uninstall them.
When trying to upgrade at first it was complaining about the ATI ACHI Compatable RAID controller not being compatable but now it starts to do the install and then on restart it does the same as the clean install.
I'm trying to install the Windows 7 32-Bit upgrade on my Dell Inspiron 1721 laptop and I get an error that says that I need to update my ATI AHCI Compatible RAID Driver. I went into the Update Device Drivers as suggested in the instructions and tried to upgrade that driver, but it says I have the latest driver for it. So I tried restarting my laptop and ran the upgrade setup again, and got the same error message.
Any ideas on what I need to do to get it to upgrade? I tried searching all over and can not find a newer version than what I have (2.5.1540.48).
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
I was recently deploying Windows 7 on an older PC(not too old) and in the upgrade proccess it said setup could not continue and rolled back my upgrade. I suspect that it is because of the raid, because it stopped in the middle of the expanding files stage.
The driver version on there is 1.0.0.62, which I believe is the most recent for vista, so can I rule this out as a reason. Theres 50GB free for upgrade.
So I installed the Windows Seven RC x64 today on my desktop machine after having a great experience on my notebook.
Most things worked out just fine, but the onboard raid controller is giving me alot of trouble (I got two hard disks connected there, should be raid0?), my mainboard is a Gigabyte GA-P35-DS3 an this is SiSoft Sandras report on my disk controllers:
Browsing this forum I found severel interesting posts, for example I tested the drivers of Driver and I tried the mainboard drivers for Vista in compatibility mode, but nothing works. I also looked for the "ITE IT8212 ATA RAID Controller" drivers directly, but there was nothing concerning Windows Seven. After that I tried the Released: Intel Chipset Software 9.1.1.1014 but that still did not solve anything.
Im using one ssd as my boot drive for windows 7 but i dont know which way i should install it. i can either use AHCI or RAID and if i choose RAID i can specify either RST or RSTe. if i install AHCI, should i install intel's rst by loading the driver before installing windows 7 or install the rst driver after? same with RAID, should i install before or after?
My system is slow to load and no real problem with using the internet. It's just when I play BF3 online my system crashes hard sometimes and powers off or I get real slow fps/ freezes up and I have to shut down the pc to get out. Windows tells me the hd controllers driver (Marvell) is not compatible with windows 7, that everything is bottle necking at the controller and suggests I go to the OEM site for an updated, compatible driver. No luck there. No driver and they claim that hd is compatible with Win 7. The hd is a Western Digital, WD 5000 AADS, 500 gig, 32 mb SATA 3. End of the road? Do I have to buy a new hd that has drivers that are compatible with windows 7?
I have an Asus Rampage IV Extreme Motherboard and have Windows 7 Installed on a 96gb kingston ssd.
I now bought 2x 256gb Samsung 830s and want to run them in raid. If I set my RAID in bios, I cannot boot into my kingston ssd, it blue screens. If I set it to AHCI I cannot run my ssds in Raid.
I can do a fresh install on the ssds but how do I move my programs and data over? BTW.. I have Norton Ghost 15 which was provided with the Sammy 830s...
Which configuration would be better using mobo sats 2 raid or using seperate rid controller via pcie card Rosewill Rc-211 wsis3132) or should I use mobo for raid and card for extra sata w/o raid I have more drives than sata slots. How do I transfer data videos/Tv shows from existing drive to raid?
I recently upgraded to an SSD. I moved windows 7 over to the new SSD and re-aligned the partition properly The drive setup is as follows:
2x 500GB WD Black drives in RAID 0 1x 120GB ADATA S510 SSD
In BIOS, RAID mode is enabled. You cannot enable RAID for one pair of drives and AHCI separately. I was assuming disks that are not part of the logical RAID volumes would be set to AHCI automatically. I have enabled NCQ in AMD RaidExpert for the SSD.WEI is 5.9 for the primary disk. The primary disk is the SSD.Other strange behanivour is that the RAID array and the SSD both appear as SCSI devices in device manager, and Windows won't accept the ahci drivers from ECS.
1 SATA HDD Primary OS Disk 2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk 1 SATA HDD Backup Disk [No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
Driver update program says new driver available 1.0. Any issues regarding updating this driver. No problems needed. Dell Inspirion laptop Win 7 Home Prem. 64bit 4gb ram
my driver updater asked me to update this driver (standard AHCI 1.0 serial ATA controller)..but i cannot do it using the software coz my internet connection is slow.So,i want to download it manually.Where can i get this driver?
I have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.
My question:
SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s. TDK DVD+R disks tested OK (on other PC) for 16X capability. Why is Nero reporting of only 2.4X and 4X writting speeds?
I'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..
Can someone hit me with a link for manually installing the AHCI driver and switching the OS mode for the storage controller.
If I remember right, this is just putting the driver in /sys/drivers, running a script, and making a registry change. Then you reboot, change the motherboard setting, and then install IMSM after the OS comes back up. I don't remember the script, or if it was just a reg edit, etc.
I've just installed Windows 7 RC build 7100 onto my system. As always like with Vista installations in the past, I run into this problem. I have a DFI Lanparty NF4 Ultra-D motherboard and for some reason my RAID drive doesn't show up. I can see the two HDs I have set up as a raid appear and separate individual drives under My Computer but can't access them unless I format them which is something I dont want to do. I checked under Device Manager and under Stoare Controllers, NVIDIA nForce RAID Controller is installed...but I think I'm missing the proper RAID tool? I'm not too sure about this.
My Device Manager lists everything as installed, but each time I restart my computer and boot up, the computer is trying to install some drives but "Failed." The prompt says, "Standard Dual Channel PCI IDE Controller" x3, and all 3 Failed to install. I have no idea if this is the actual problem because I'm trying to get my RAID Stripe to work and they are both on SATA connections and not IDE...I have tried a few sets of nForce packs such as Fernandos_XP_64bit_nForce4-5_non-AHCI_WHQL_PACK_v5.4 but no avail.
Anyone managed to find Windows 7 compatiable drivers for "GigaRAID ITE8212 IDE RAID controller"?
I tried using the Vista drivers in compatibilty mode but no luck unfortunately. Issue being is that my 2nd internal hard drive is not showing up in My Computer however it is listed in device manager. This is the only item left in device manager that isnt installed properly :-(
I checked my motherboard drivers page @ GIGABYTE - Product - Motherboard - Specification - GA-8I955X Pro but they only have Vista drivers listed.
I've been trying to find the drivers suitable for Windows SEVEN. I need it to use a couple of hdd in pair with RAID configuration. Before anything :I tried the RAID with VISTA64 and worked perfectly so I don't need to set that part in bios..etc..
So now it's SEVEN turn... I simply can't find the drivers... it says that they are not signed by microsoft so they can't be used.
I was trying with some controller RAID drivers from other MB...newer versions but I haven't found any good luck by far.
I am going to be getting 2 new WD10EALS drives in the next day or so. My plan was to put them in raid using the onboard ICH10R controller on my mobo (an ASUS Sabertooth X58). I had wanted to run WDTLER to turn TLER on, but after reading some reviews it seems I might not be able to as it is reported WD disabled TLER on these drives completely.
Im curious if there is a way to change the timeout for the drives in the matrix storage controller? So if I do have an issue my raid won't die (I'll be using these drives in raid 0 for gaming only). I dont care about the data, I just don't want to have to go thru the hassle of reinstalling the games should a drive get dropped from the array. I am thinking about getting a wd green 2tb drive for backups but just curious if there is a way to change timeout via the controller.
edit: And by change timeout I mean how long the controller waits for the disk before dropping it from the array, like could i set it too 2.5 mins just to be sure?
My win 7 machine boots perfectly with two SATA mirrored drives and a Promise Ultra 133 TX2 IDE controller card with no drives attached. But when I connect drives to either IDE1 or IDE2, the machine will not even get to win start up.
How can I uninstall a Gigabyte raid contoller without crashing my Win 7 OS? Uninstall is being prevented because "the OS is on the contoller"! Win 7 64 bit is on a Crucial SSD boot drive and AHCI is set in BIOS. However the raid controller is setting all internal drives to SCSI!