SATA Driver Issue W/ Win 7 And Gigabyte GA-MA785G-UD3H
Nov 4, 2009
Using Win 7 64-bit with AMD SATA drivers with a strange issue.
When this board boots up it does an AHCI initialization which shows the attached sata drives. After that, Windows 7 loads and runs without a problem. However, when I reboot Windows it sounds like the hard drives spin speed is slowing down then speeding up again.
It does this about 4 times then the computer shuts down. When the computer restarts and goes back to the AHCI init screen it now shows "S.M.A.R.T. Error", but Windows boots without a problem. If the computer is shut down (powered off) the next boot will not show the error.
I've had Windows 7RC 32-bit, and currently also have XP-64 and XP-32 partitions on this machine with no problems at all. If I set the machine to Native IDE instead of AHCI everything goes back to normal with no shutdown issues.
Any ideas?
View 9 Replies
ADVERTISEMENT
Jun 30, 2012
Wasn't exactly sure where to put this question.I have a machine with a h67a-ud3h-b3 MOBO abd an currently using both video outputs. Nice board. Does anyone know if I can add an addtional video card to the board without having to disable the on-board video. Yes, I'd like a 3 or 4 monitor system. Everything I've found on the subject is very vague.
View 1 Replies
View Related
Sep 21, 2012
I installed all the drivers available from the Gigabyte website for some reason the wifi function simply does not work. Also, the screen plugged into the 7950 works fine but the other screen connected into the motherboard gets the message "no signal detected".
View 1 Replies
View Related
Sep 10, 2012
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
View 9 Replies
View Related
Nov 12, 2011
I have a Western Digital 1 TB USB 2.0 that I have connected to a computer that has Gigabyte connection to my NAS which can handle Gigabyte speeds.I am only getting 30.1MB/s.Is there any settings I can do to windows so that it can send faster?
View 1 Replies
View Related
Jul 4, 2012
I bought a Gigabyte GA-Z68X-UD3H-B3 mobo and while checking the Memory QVL on their website I saw that they have not listed 8gb individual sticks of ram.They provide the Module P/N of 2x4gb and 2x2gb ram packages.I have learn that the Module P/N number has to be very respected to secure the compatibility, but when I for example look for the 2x4gb ram package specs on a different package (1x8gb), the Module P/N changes slightly and it is not found on my mobo's QVL. Is there a problem if I choose the 1x8gb package even thought the serial number varies slightly?I already bought a 2x4gb ram package because I did not think that in order to take full advantage of ram slots capacity (get to 32gb) I have to use 1x8gb sticks.So now that I have 2x4gb ram in my system, is it possible to use the other 2 empty slots and use a 2x8gb package in order to have 24gb in my system?
View 9 Replies
View Related
Sep 20, 2009
I have been running win 7 for about 6 mths now dual boot with xp. I have done a fresh install and got rid of xp and running win 7 straight up. My system is a Gigabyte AM2+ with a phenomII black edition 4 core., 4gb ram onboard video.
Now for the question. i got thinking today and realized i hadnt installed any chipset drivers etc. I look in device manager and all the drivers are from microsoft and from 2006 ? So i go to gigabyte and get the win 7 download but all it installs is the graphic driver and usb filter driver nothing else. I try driver max and it says my drivers are up to date. What am i missing here.
View 4 Replies
View Related
Nov 30, 2009
I have been trying to install Windows 7 x64 Ultimate on a Gigabyte GA-P35-DS3 (rev 2.0)
and everytime i do the install fails and the install is then rolled back.
I currently have Vista x32 installed on Gigabyte Raid 0 (there's also an intel raid option but i've never used it). The Vista install runs fine and i've never had a problem.
When i try to install using the GA-P35-DS3 (rev 2.0) raid drivers from the Gigabytes site i get the usual microsoft grumbles about unsigned drivers but then the install seems to go OK from there until the install completes and reboots. At this point it errors out and reboots into the OS rollback install.
Does anyone know if this is an issue with this driver or does anyone have a link to another driver?
View 8 Replies
View Related
Dec 24, 2011
I have vga driver for win xp, but it doesn't work on win 7. My motherboard is Gigabyte GA-8SIMLH. What can i do now ?
View 2 Replies
View Related
Sep 14, 2009
Im an owner of the M912M netbook with Windows 7 RC 7100. I bought recently a external network adapter (Rokland N3) based on the Ralink RT2870 chipset and i have a problem connecting it to the netbook.
Installed the software+driver that came with it on CD and when connecting the adapter Windows says "Driver didn't install etc. etc.". Tried a Windows 7 driver which came from Ralink for this chipset and says same thing. Also Windows Update finds the driver but everytime it tries to install it it comes with a error (80070002, to delete all temp files of the WU, done that but same) and doesn't install it.
Same adapter installed and works fine on different laptops, Sony Vaio VGN-A497XP with same Windows 7 RC 7100, Acer 4630Z with Windows Vista so it shouldnt be a driver or OS problem but something specific to the M912.
Contacted Rokland and they guessed that it should e conflicting with the internal adapter so i removed it together with its driver but nothing.
View 1 Replies
View Related
Oct 10, 2011
i'm having trouble installing the latest catalyst drivers.the package fails and keeps knocking me back with the INF file was not find.ive installed the package to a folder and tried to navigate via system and update the driver file but get an error regarding the information set or element settings (and the driver doesn't update.my graphics card is still working so to speak, i can enter games although my system crashed 2 hrs ago from dxgmm1.sys and thats what prompted me to uninstall and reinstall my drivers but im running into alot of problems.i've also tried reinstalling through safe mode and still not working (ive used driver sweeper to make sure it's a fresh install)
View 4 Replies
View Related
Dec 4, 2009
I thought this was going to be an easy fix, but...Quick Setup: Motherboard is a Gigabyte GA-MA770-DS3 version 1.0; I am setting RAID zero with two WD 160gig HDs. A Pioneer DVD drive and a Lite-On DVD drive. This is a 64-bit install.
I set the RAID config and cleaned the drives. Popped the Windows 7 install disk in my DVD drive and the install began. Set the language prefs and clicked 'Install.' Shortly after I get the following error...Load Driver
A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. My first guess was not a CD/DVD driver but a RAID driver is needed. I tried using the latest RAID drivers from Gigabyte. I made sure I was using the 64-bit version of the drivers.
When installing the driver, Windows install responds with "can not find the drive." 'Drive' not 'driver.'
There are no drivers available for my two DVD drives. The standard Windows driver has always been sufficient. What driver is the install is looking for? Do you think I may have missed something in the RAID config?
View 6 Replies
View Related
Feb 18, 2011
I recently had to format my H/D however cannot find my original drivers disc. So I cannot connect to the internet to get drivers.Motherboard is a gigabyte-ga=81865gm-775Have tried the gigabyte site but cannot find the driver there
View 6 Replies
View Related
Jun 16, 2009
I have been reading for days and don't understand this. When I get a system built using all SATA drives...is the best setting in the bios AHCI?
I know the RAID setting requires drivers and IDE does not but how about AHCI?
Should I even use this setting? Does it require drivers or does Windows 7 have "generic" ones?
View 8 Replies
View Related
Jun 25, 2009
So I installed the Windows Seven RC x64 today on my desktop machine after having a great experience on my notebook.
Most things worked out just fine, but the onboard raid controller is giving me alot of trouble (I got two hard disks connected there, should be raid0?), my mainboard is a Gigabyte GA-P35-DS3 an this is SiSoft Sandras report on my disk controllers:
Browsing this forum I found severel interesting posts, for example I tested the drivers of Driver and I tried the mainboard drivers for Vista in compatibility mode, but nothing works. I also looked for the "ITE IT8212 ATA RAID Controller" drivers directly, but there was nothing concerning Windows Seven. After that I tried the Released: Intel Chipset Software 9.1.1.1014 but that still did not solve anything.
View 6 Replies
View Related
Dec 11, 2012
Just did a fresh install of Windows 7 Ultimate 64bit. Trying to install the motherboard chipset but got confused with these options. Which one do I install? Asetup or Setup? Motherboard is Gigabyte 880-GMA U2DH rev2.1
View 5 Replies
View Related
Jul 25, 2012
The Gigabyte Z77X-UD5H WB comes with a Wireless Adapter/Bluetooth PCIe card.
Atheros AR5BWB222. Gigabyte calls it a GC-WB300D
The driver is being reported as having an issue by a splat in device manager with the following message: Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52). The Card works fine in another system that also runs Windows 7 x64 Pro.
I have called Gigabyte, uninstalled and the reverse in safe mode also. Done everything I know. Why it works in one system and not this one is the key. Once it was seen to work on another system Gigabyte tossed me into the ditch.
I have tried drivers from the boxed CD and their site. The Bluetooth side of the card which uses its own drivers is OK.
Windows 7 X64 Pro SP1
Gigabyte Z77X-UD5H WB
Intel 3770K
Kingston 16GB 2133 Genesis RAM
Corsair 750Watt Pro Series
Sapphire 6850 GPU
View 9 Replies
View Related
Apr 25, 2012
What can I do to make my graphics card work perfect but not messing up the pc I have tried downloading the drivers got hold of various versions tried them but they kept on giving me the problem, with a black screen after window logo loading.
View 9 Replies
View Related
Aug 10, 2010
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
View 9 Replies
View Related
Jun 27, 2012
Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?
View 9 Replies
View Related
Aug 10, 2011
i want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7
View 4 Replies
View Related
May 7, 2011
i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
View 5 Replies
View Related
Nov 24, 2009
Does any one know how to install sata drivers After XP has been installed?
I have a HP DV6150CA and I have to disable my SATA NATIVE from the bios just to be able to load XP.. But when I dual boot to Win 7 I can use it, disabled or enabled it works either way...
View 2 Replies
View Related
Apr 1, 2011
...every time I boot my system, Windows says it is installing the SATA driver. BIOS entries are OK, once drivers are installed, Disk Management shows everything OK too. So, what could be the cause for this? I have two disks, the System SSD (OCD Vertex II 60GB SATA) must have its driver installed to boot Windows, so the msg must refer to the second HD (Seagate 1TB SATA
View 1 Replies
View Related
Nov 5, 2009
I've just bought parts and collected a new PC system. My Motherboard is AsRock M3A785GXH/128 ASRock > Products > M3A785GXH/128M
and regarding to the manufacturer it should be Windows 7 hardware ready.
But I can't install Windows 7 pro 64 bit on my new system. The Windows 7 installation application can't see my harddrives and want a driver to them. I assume that should be a driver for the SATA controller on the motherboard. I've tryed to use the drivers on the motherboard cd-rom and tryed to use the drivers froms asrock homepage, but Windows 7 wont accept them.
I have contacted AsRock about this issue, but I'm wating for an answer and hoped that you guys might has seen this problem before, and will answer quicker than AsRock Support
I should say that I cant install Windows Vista Business 64bit without any problems at all.
View 9 Replies
View Related
Sep 21, 2010
As I look around to gather drivers for a new install of Win 7 Pro from XP Pro, I am having a problem, the inf file. Does Win 7 have the inf file for GA-965P/DS3? I am also not sure about the SATA driver for the Gigabyte controller, since this is the one my sys HD is connected to; the ones I have on the disk that came with the mobo...earlier than Windows 7.
View 4 Replies
View Related
Feb 25, 2011
I have an asus m2n32ws pro motherboard and am running win 7 ultimate 64 bit and have a problem device _ it is a sata controller that has no driver and i have searched and cannot find out a what the device is nor b a driver anywhere
View 6 Replies
View Related
May 12, 2012
Driver sata samsung HM250HI?
View 1 Replies
View Related
Jul 4, 2012
I bought a usb 2.0 to sata / ide so I could connect my old external hard drive from my old Windows XP computer to my windows 7 laptop. The USB 2.0 only wotls with Win 98, XP, ME and 2000. I need some thing that I can use to connect it to my Win 7 notebook.
View 4 Replies
View Related
Mar 30, 2012
When I open the PC, my hardrive and DVD rom was detected in bios but when the operating system started it shows the windows logo then after a second it shows a message that "the driver not found. Im confuse because i have only one hardrive which is the win7 installed on it. How can possibly that the PC did not find this driver but it shows the logo of win7?
View 1 Replies
View Related
Jul 28, 2009
I´m trying to install Seven x86 on Abit NF7-S v2.0 with Sata HDD (non RAID), tried several drivers but didn´t work.
Have you got some working driver for this old chipset? The sata controller is SIL3112A.
View 1 Replies
View Related
