Gigabyte GA-P35-DS3 Raid Driver
Nov 30, 2009
I have been trying to install Windows 7 x64 Ultimate on a Gigabyte GA-P35-DS3 (rev 2.0)
and everytime i do the install fails and the install is then rolled back.
I currently have Vista x32 installed on Gigabyte Raid 0 (there's also an intel raid option but i've never used it). The Vista install runs fine and i've never had a problem.
When i try to install using the GA-P35-DS3 (rev 2.0) raid drivers from the Gigabytes site i get the usual microsoft grumbles about unsigned drivers but then the install seems to go OK from there until the install completes and reboots. At this point it errors out and reboots into the OS rollback install.
Does anyone know if this is an issue with this driver or does anyone have a link to another driver?
View 8 Replies
ADVERTISEMENT
Jun 25, 2009
So I installed the Windows Seven RC x64 today on my desktop machine after having a great experience on my notebook.
Most things worked out just fine, but the onboard raid controller is giving me alot of trouble (I got two hard disks connected there, should be raid0?), my mainboard is a Gigabyte GA-P35-DS3 an this is SiSoft Sandras report on my disk controllers:
Browsing this forum I found severel interesting posts, for example I tested the drivers of Driver and I tried the mainboard drivers for Vista in compatibility mode, but nothing works. I also looked for the "ITE IT8212 ATA RAID Controller" drivers directly, but there was nothing concerning Windows Seven. After that I tried the Released: Intel Chipset Software 9.1.1.1014 but that still did not solve anything.
View 6 Replies
View Related
Dec 18, 2012
How can I uninstall a Gigabyte raid contoller without crashing my Win 7 OS? Uninstall is being prevented because "the OS is on the contoller"! Win 7 64 bit is on a Crucial SSD boot drive and AHCI is set in BIOS. However the raid controller is setting all internal drives to SCSI!
View 1 Replies
View Related
Sep 10, 2012
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
View 9 Replies
View Related
Nov 19, 2011
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
View 1 Replies
View Related
Nov 12, 2011
I have a Western Digital 1 TB USB 2.0 that I have connected to a computer that has Gigabyte connection to my NAS which can handle Gigabyte speeds.I am only getting 30.1MB/s.Is there any settings I can do to windows so that it can send faster?
View 1 Replies
View Related
Sep 20, 2009
I have been running win 7 for about 6 mths now dual boot with xp. I have done a fresh install and got rid of xp and running win 7 straight up. My system is a Gigabyte AM2+ with a phenomII black edition 4 core., 4gb ram onboard video.
Now for the question. i got thinking today and realized i hadnt installed any chipset drivers etc. I look in device manager and all the drivers are from microsoft and from 2006 ? So i go to gigabyte and get the win 7 download but all it installs is the graphic driver and usb filter driver nothing else. I try driver max and it says my drivers are up to date. What am i missing here.
View 4 Replies
View Related
Dec 24, 2011
I have vga driver for win xp, but it doesn't work on win 7. My motherboard is Gigabyte GA-8SIMLH. What can i do now ?
View 2 Replies
View Related
Sep 14, 2009
Im an owner of the M912M netbook with Windows 7 RC 7100. I bought recently a external network adapter (Rokland N3) based on the Ralink RT2870 chipset and i have a problem connecting it to the netbook.
Installed the software+driver that came with it on CD and when connecting the adapter Windows says "Driver didn't install etc. etc.". Tried a Windows 7 driver which came from Ralink for this chipset and says same thing. Also Windows Update finds the driver but everytime it tries to install it it comes with a error (80070002, to delete all temp files of the WU, done that but same) and doesn't install it.
Same adapter installed and works fine on different laptops, Sony Vaio VGN-A497XP with same Windows 7 RC 7100, Acer 4630Z with Windows Vista so it shouldnt be a driver or OS problem but something specific to the M912.
Contacted Rokland and they guessed that it should e conflicting with the internal adapter so i removed it together with its driver but nothing.
View 1 Replies
View Related
Oct 10, 2011
i'm having trouble installing the latest catalyst drivers.the package fails and keeps knocking me back with the INF file was not find.ive installed the package to a folder and tried to navigate via system and update the driver file but get an error regarding the information set or element settings (and the driver doesn't update.my graphics card is still working so to speak, i can enter games although my system crashed 2 hrs ago from dxgmm1.sys and thats what prompted me to uninstall and reinstall my drivers but im running into alot of problems.i've also tried reinstalling through safe mode and still not working (ive used driver sweeper to make sure it's a fresh install)
View 4 Replies
View Related
Dec 4, 2009
I thought this was going to be an easy fix, but...Quick Setup: Motherboard is a Gigabyte GA-MA770-DS3 version 1.0; I am setting RAID zero with two WD 160gig HDs. A Pioneer DVD drive and a Lite-On DVD drive. This is a 64-bit install.
I set the RAID config and cleaned the drives. Popped the Windows 7 install disk in my DVD drive and the install began. Set the language prefs and clicked 'Install.' Shortly after I get the following error...Load Driver
A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. My first guess was not a CD/DVD driver but a RAID driver is needed. I tried using the latest RAID drivers from Gigabyte. I made sure I was using the 64-bit version of the drivers.
When installing the driver, Windows install responds with "can not find the drive." 'Drive' not 'driver.'
There are no drivers available for my two DVD drives. The standard Windows driver has always been sufficient. What driver is the install is looking for? Do you think I may have missed something in the RAID config?
View 6 Replies
View Related
Feb 18, 2011
I recently had to format my H/D however cannot find my original drivers disc. So I cannot connect to the internet to get drivers.Motherboard is a gigabyte-ga=81865gm-775Have tried the gigabyte site but cannot find the driver there
View 6 Replies
View Related
Jun 16, 2009
I have been reading for days and don't understand this. When I get a system built using all SATA drives...is the best setting in the bios AHCI?
I know the RAID setting requires drivers and IDE does not but how about AHCI?
Should I even use this setting? Does it require drivers or does Windows 7 have "generic" ones?
View 8 Replies
View Related
Dec 11, 2012
Just did a fresh install of Windows 7 Ultimate 64bit. Trying to install the motherboard chipset but got confused with these options. Which one do I install? Asetup or Setup? Motherboard is Gigabyte 880-GMA U2DH rev2.1
View 5 Replies
View Related
Jul 25, 2012
The Gigabyte Z77X-UD5H WB comes with a Wireless Adapter/Bluetooth PCIe card.
Atheros AR5BWB222. Gigabyte calls it a GC-WB300D
The driver is being reported as having an issue by a splat in device manager with the following message: Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52). The Card works fine in another system that also runs Windows 7 x64 Pro.
I have called Gigabyte, uninstalled and the reverse in safe mode also. Done everything I know. Why it works in one system and not this one is the key. Once it was seen to work on another system Gigabyte tossed me into the ditch.
I have tried drivers from the boxed CD and their site. The Bluetooth side of the card which uses its own drivers is OK.
Windows 7 X64 Pro SP1
Gigabyte Z77X-UD5H WB
Intel 3770K
Kingston 16GB 2133 Genesis RAM
Corsair 750Watt Pro Series
Sapphire 6850 GPU
View 9 Replies
View Related
Nov 4, 2009
Using Win 7 64-bit with AMD SATA drivers with a strange issue.
When this board boots up it does an AHCI initialization which shows the attached sata drives. After that, Windows 7 loads and runs without a problem. However, when I reboot Windows it sounds like the hard drives spin speed is slowing down then speeding up again.
It does this about 4 times then the computer shuts down. When the computer restarts and goes back to the AHCI init screen it now shows "S.M.A.R.T. Error", but Windows boots without a problem. If the computer is shut down (powered off) the next boot will not show the error.
I've had Windows 7RC 32-bit, and currently also have XP-64 and XP-32 partitions on this machine with no problems at all. If I set the machine to Native IDE instead of AHCI everything goes back to normal with no shutdown issues.
Any ideas?
View 9 Replies
View Related
Apr 25, 2012
What can I do to make my graphics card work perfect but not messing up the pc I have tried downloading the drivers got hold of various versions tried them but they kept on giving me the problem, with a black screen after window logo loading.
View 9 Replies
View Related
Aug 24, 2012
I need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies
View Related
Jan 1, 2013
I had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.
View 4 Replies
View Related
Apr 25, 2012
I have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
View 2 Replies
View Related
Aug 12, 2012
Which configuration would be better using mobo sats 2 raid or using seperate rid controller via pcie card Rosewill Rc-211 wsis3132) or should I use mobo for raid and card for extra sata w/o raid I have more drives than sata slots. How do I transfer data videos/Tv shows from existing drive to raid?
View 1 Replies
View Related
Oct 1, 2009
I've recently bought ST-Lab A142 PCI ATA 133 IDE Card to make RAID to make RAID from my 2 HDD drives 60GB each.
It comes with a cd on which there are drivers for win 2000/xp/vista 32/64bit. But no mention of Windows 7. I am trying to install Windows 7 x64 on this RAID but it doesn't see RAID. I've tried downloading the lates drivers from ST-Lab official site but with no success, Windows 7 just doesn't want to install them. Is there any solution u can advice?
View 4 Replies
View Related
Oct 28, 2009
I had to move the hard drive that I installed W7rc on to a SATA port that is configured in the BIOS as a raid. Now it will not startup because it needs the raid driver installed.
How can I install that driver?
I have tried "Startup repair" and it tells me it can not fix the problem. I tried to do an upgrade and you all know what it said. Must boot into that os first then do the upgrade.
View 9 Replies
View Related
Oct 31, 2009
I have 2x 500GB Western Digital WD5001AALS Caviar Blacks. I have set the BIOS up for raid 0 instaled a intel raid driver during install (not f6) windows 7 64bit says that its one drive and lets me install it but when i go to device manager it says that there is no driver installed. i have installed intels matrix storage manager thats relling me that raid 0 is operating (but is as os not saying that there is no driver) i have a bloodrage mobo.
View 2 Replies
View Related
Feb 9, 2010
am trying to install win7 (no beta) on Qosmio F30-140. I start the installation and the files are copying to the hdd. Then the computer starts again for the installation.
But every start is ending in a blue screen with error: stop 0x0000007E.
View 2 Replies
View Related
Jul 24, 2009
I was recently deploying Windows 7 on an older PC(not too old) and in the upgrade proccess it said setup could not continue and rolled back my upgrade. I suspect that it is because of the raid, because it stopped in the middle of the expanding files stage.
The driver version on there is 1.0.0.62, which I believe is the most recent for vista, so can I rule this out as a reason. Theres 50GB free for upgrade.
View 6 Replies
View Related
Oct 22, 2009
I'm trying to install the Windows 7 32-Bit upgrade on my Dell Inspiron 1721 laptop and I get an error that says that I need to update my ATI AHCI Compatible RAID Driver. I went into the Update Device Drivers as suggested in the instructions and tried to upgrade that driver, but it says I have the latest driver for it. So I tried restarting my laptop and ran the upgrade setup again, and got the same error message.
Any ideas on what I need to do to get it to upgrade? I tried searching all over and can not find a newer version than what I have (2.5.1540.48).
View 9 Replies
View Related
Nov 3, 2009
I have a PC with ULi M1575/M1697 chipset, was wondering if anyone has found a raid driver that works in 7 or if 7 has it built in.
I know nvidia bought them out a long time ago and realize this is probably not going to work.
View 3 Replies
View Related
Oct 25, 2009
I am doing a clean install of Win 7 Ultimate 64bit. I have a Gigabyte GA-MA790FX-UD5P Motherboard and a LG GGW-h20L Blu ray writer. I can install Windows 7 fine on a single SATA disk setup with the bios settings set to IDE. But when I set the bios settings to RAID and plug the 2 hard disks in and run the windows setup it asks for the CDDVD rom driver. It does not do this when setting it up on a single disk. I have tried the AHCI option, SATA, option, IDE options
I have the latest bios and have tried locating the drivers for the LG writer but was unable to find them. The LG writer already has the latest firmware installed.
My motherboard has a SB750 chipset RAID controller.
View 4 Replies
View Related
Dec 13, 2009
Recently I got a newly Windows 7 Ultimate Edition from my friend. Like my old Vista X64, I ran the normal setup for Windows set the boot piority to DVD-Drive and the usual bla bla bla stuff...
I've installed countless times of Vista on my PC without any problem, but Windows 7 is currently pissing me off.
When I got the Windows 7 DVD from my friend I instantly went to ASUS site for some drivers for my RAID setup (for some reason it wasn't list in the download section for this motherboard), like my Vista installation, I've put the files in the thumb drive. When Windows asked me for the drivers, I've just put the thing in to my PC and BAM!! Windows doesn't see my drivers
So I've done some research and tried out different drivers, but none of them worked.
After countless hours of trial and error, I finally given up the "clean" installation of Windows 7. So I've tried the "upgrade" method in Vista instade. The process was easy, a few clicks (and miracally it detects my RAID 0 too). The installation went real smooth, after the PC reboots itself and the shiny Windows logo was on the screen with the message "Starting Windows". WHOOOF!! BSOD saying 0x0007b error. I've tried installing it again using "upgrade" option, but the result was the same.
PS. Just to remind you there are two question
1. Why doesn't Windows detect my drivers
2. Why is showing this "0x0007b" BSOD all the time
View 4 Replies
View Related
May 30, 2011
need drivers for ultra ata/133 pct raid card for window 7 pro
View 1 Replies
View Related
