I´m trying to install Seven x86 on Abit NF7-S v2.0 with Sata HDD (non RAID), tried several drivers but didn´t work.
Have you got some working driver for this old chipset? The sata controller is SIL3112A.
I have an Abit NF7-S mobo (5+ yrs old) that has an nForce2 Ultra 400 + MCP-T chipset. The nvidia site has classified this as legacy, and only has the download for Vista.
Well I usually prefer to install the 'official' drivers, as MS ones seem to be at times problematic from experience. However I went along with installing the ones provided my microsoft update. All components in Device Manager seem to have been installed, and the OS is working without a problem.
But the voice within me still prefers the 'official' vendor software. Would the vista one provided by nvidia work on Windows 7. I use to get a nice small app to control audio in the official release, which I am obviously not getting in the MS trimmed version.
I also have a SATA 150 RAID (Silicon Image Sil 3112A SATA PCI Controller) on the NF7-S which has the same issue as above. All working.. but for that voice.
I've just bought parts and collected a new PC system. My Motherboard is AsRock M3A785GXH/128 ASRock > Products > M3A785GXH/128M
and regarding to the manufacturer it should be Windows 7 hardware ready.
But I can't install Windows 7 pro 64 bit on my new system. The Windows 7 installation application can't see my harddrives and want a driver to them. I assume that should be a driver for the SATA controller on the motherboard. I've tryed to use the drivers on the motherboard cd-rom and tryed to use the drivers froms asrock homepage, but Windows 7 wont accept them.
I have contacted AsRock about this issue, but I'm wating for an answer and hoped that you guys might has seen this problem before, and will answer quicker than AsRock Support
I should say that I cant install Windows Vista Business 64bit without any problems at all.
I have an asus m2n32ws pro motherboard and am running win 7 ultimate 64 bit and have a problem device _ it is a sata controller that has no driver and i have searched and cannot find out a what the device is nor b a driver anywhere
View 6 Replies View RelatedVery little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
View 5 Replies View RelatedMy MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?
View 5 Replies View RelatedI purchased this add-on card for my older AMD 2400mhz 1gb ram box. This is the computer with Windows 7 on the 500gb Pata IDE hard Drive. I wanted to add a 1TB Sata drive since the MB does not have sata. The card has 2 sata connections, 4 USB ports, & 1 IDE connection. It just plugs into an empty PCI slot. For some reason Windows 7 does not detect the card & when I try to install the drivers Windows 7 says cannot detect any hardware. The card has VIA VT6421A chipsets.
View 4 Replies View RelatedI have an adaptec sata controller card, which I was contemplating using for running my two raid drives.
I know that there are Vista 64 drivers availiable to download, and so my question is this,
will Vista 64 disk drivers work with Windows 7 Beta build 7000?
I thought i'd ask here first, as it seems silly to reformat and save disc images, reinstall etc, if someone here already knows the answer.
Also, is there a simple way transferring all the user's data and programme data if I wanted to upgrade to a newer build, as obviously backing up the disc image won't work I suppose with a newer build of 7?
what Sata card i need to add extra hard drives to my system I am running Windows 7 Ultimate 64 Bit
View 3 Replies View RelatedThe mobo's kinda old, and not the greatest; the builtin SATA only works for Raid, so I put in a PCI sata card with the SIL3114 chipset. The computer now sees the 64GB SSD Patriot HD I'm trying to use for her C drive (The SSD is a leftover from a different project... I thought it'd lend some additional performance to help make up for the 1.2 ghz cpu). When I get into Windows setup, though, Windows 7 does not recognize the drive, and none of the drivers that came with the PCI card seem to work. I suppose I should have double checked before buying the SATA PCI card to find one that has native Windows 7 drivers, but I thought the stone age days of needing SATA drivers were over, guess I was wrong!
View 4 Replies View RelatedI have 2 IDE DVD drives (TEAC DV-W516D DVD/CD ReWriter, and TSSTcorp DVD-ROM SH-D162C DVD/CD Reader). Teac is capable of 16X DVD writting. My motherboard Gigabyte Z77-D3H has only SATA II/III slots. So I connected each IDE optical drive to motherboard's SATA II slot(s) using IDE to SATA I adapters (1 adapter per optical drive). Windows 7 Ultimate 32bit is running, and SATA AHCI is being used.
My question:
SATA I = 1.5Gbps = 187.5MB/s (adapter capability) is faster then DVD 16X writting = 177.28Mbps = 22.16MB/s.
TDK DVD+R disks tested OK (on other PC) for 16X capability.
Why is Nero reporting of only 2.4X and 4X writting speeds?
I own a lenovo thinkpad and recently all of a sudden i recieved this messg where it says mediatest failed, check cable, the solutions stated i change my SATA controller to compatible mode from AHCI to IDE most perferably. Id like to know step by step how i can do it myself.
View 1 Replies View RelatedDoes anyone know where I might find the 64 bit ".inf" drivers for Windows 7 64 bit?
View 3 Replies View RelatedI updated the SATA AHCI controller from device manager and rebooted. Shortly after I noticed disk drives F:, Z:, and X: are gone. No big deal I'll just repartition right? No they aren't showing up in Disk Management? The driver I installed I got from gigabyte it was a preinstall driver for ahci. I just installed windows 7 64 yesterday to a Samsung 830 256gb and it was working fine maybe I shouldn't have messed with it. C: drive is working fine just the other 3. Should I roll the driver back? System restore? Did I install the wrong driver?
View 3 Replies View RelatedI'm going to install RC1 in the next few days.
I was looking to test the stability within RC1 of an adaptec 1220SA card I have to control the system drives. I have the Vista 64bit driver for the card as this is the newest listed.
I have created a recovery disc in beta build 7000 and hope to use this to boot into a DOS shell and follow the instructions given on the adaptec site:
This is the BIOS release v6.0-0 Build 2330 for the Adaptec SATA II RAID 1220SA Controller.
This BIOS should only be used together with Driver v1.6.12086 in Windows Server 2008 or Windows Vista.
This self-extracting archive includes the flash utility, the BIOS image file and the Release Notes.
Caution: If the BIOS update fails with an error message "unable to find file" or "target controller does not match", please see ASK Answer ID 15241
Installation Instruction: This file is self extracting and will unzip to the directory adaptec1220sa. Copy the expanded files to a floppy diskette. The expanded files can also be copied to a USB device or CD-R.
Shut down the operating system and reboot to DOS from a bootable floppy disk, USB device or CD-R. Insert the media with the update files. Run the flash utility program named AFU.EXE included in this download to backup the current BIOS and flash the new BIOS image.
I'm hoping to expand the bios update file onto a cd for the second drive or alternatively stick it on a USB stick.
My question is this, when I am in the dos shell, what do I do!
I suddenly realised that i've never had a need to use the command line
Quick summary: SATA Controllers on motherboard are not working. Ordered and installed a PCI-E SATA Controller Card. Connected Hard Drive & DVD Drive to new card ports. Upon attempting to boot installed windows 7, it spontaneously restarts before loading. It seems that I need to get the Controller Card's drivers installed. i try startup repair mode, and I can load the driver and see the Windows 7 installation after that, but then I don't know how to permanantly add the drivers for this installation.
View 1 Replies View Relatedi installed a sata controller because the sata controller on the motherboard went out. I can easily install ubuntu but when i try installing win 7 it asks for a cdrom driver, when i try booting from usb it asks for hdd driver.
View 1 Replies View RelatedI'm attempting to install a retail copy of Windows 7 Ultimate 64-Bit (VPCEB15FM) or "PCG-71312L" on this laptop. However, this message appears: "A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now." The problem is that I cannot find the Intel 5 Series 4 Port SATA AHCI Controller drivers for Windows 7 64-Bit to put on a floppy or USB drive. I've combed the Sony website and Google and the only Intel 5 Series 4 Port SATA AHCI Controller Drivers that can be placed on a floppy or USB are for Windows XP. Without the TXTSETUP.OEM, I'm dead in the water! The 64-Bit drivers (INDOTH-00215023-0042.EXE) are for an already installed Windows 7. BTW guys, the the BIOS settings on this laptop is as anemic as it gets, so there is really no way to optimize there..
View 6 Replies View RelatedJust wondering if anyone else is using this chipset and what drivers you are using?
EDIT: i advise not to try the xp drivers they messed up my install, i am using the ones supplied with win update but im sure something is missing, in my device manager it has a unknown pci device, i don't have this in xp on the same machine...??
Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?
View 9 Replies View Relatedi want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7
View 4 Replies View RelatedDoes any one know how to install sata drivers After XP has been installed?
I have a HP DV6150CA and I have to disable my SATA NATIVE from the bios just to be able to load XP.. But when I dual boot to Win 7 I can use it, disabled or enabled it works either way...
...every time I boot my system, Windows says it is installing the SATA driver. BIOS entries are OK, once drivers are installed, Disk Management shows everything OK too. So, what could be the cause for this? I have two disks, the System SSD (OCD Vertex II 60GB SATA) must have its driver installed to boot Windows, so the msg must refer to the second HD (Seagate 1TB SATA
View 1 Replies View RelatedAs I look around to gather drivers for a new install of Win 7 Pro from XP Pro, I am having a problem, the inf file. Does Win 7 have the inf file for GA-965P/DS3? I am also not sure about the SATA driver for the Gigabyte controller, since this is the one my sys HD is connected to; the ones I have on the disk that came with the mobo...earlier than Windows 7.
View 4 Replies View RelatedDriver sata samsung HM250HI?
View 1 Replies View RelatedI bought a usb 2.0 to sata / ide so I could connect my old external hard drive from my old Windows XP computer to my windows 7 laptop. The USB 2.0 only wotls with Win 98, XP, ME and 2000. I need some thing that I can use to connect it to my Win 7 notebook.
View 4 Replies View RelatedWhen I open the PC, my hardrive and DVD rom was detected in bios but when the operating system started it shows the windows logo then after a second it shows a message that "the driver not found. Im confuse because i have only one hardrive which is the win7 installed on it. How can possibly that the PC did not find this driver but it shows the logo of win7?
View 1 Replies View RelatedI'm in a fight with windows 7.
The problem is i'm having is that i can't find any sata drivers for my Promise 378 controller.
I am trying to install Windows 7 x64 edition.
But no luck so far.
In the bios i have set the promise chipset to operate in IDE mode.
Because i'm using only 1 drive.
Tried the VIA drivers for the onboard chipset as well, they only operate in raid.
So those won't work.
Spend like 5 hours online googling for it but no luck so far.
Is there a Sata driver for Asus A7N8X-E Deluxe on Windows 7?
I've been searching on the net but I'm unable to find a driver and need it for Windows 7 install on Sata drive.
I just recently purchased an Asus M4N78 Pro motherboard, and was building a system, installed Windows 7RC 64bit and I am running into a bit of an issue. The install went fine and everthing, except for the SATA ports 5 and 6 do not detect the drives attached to those ports. According to teh manual I need to install a driver from the disc, and that is teh problem. The disc apparently will not run under windows 7.
Does anyone happen to know where I could get teh particular driver I need? It would be nice to actually use all six of the boards SATA ports. The Asus website was not much help, nor was their customer service line. According to the manual the chipset is NVIDIA GeForce 8300 .... did a search on their site as well and was unable to locate what I need.