In a new build I'm trying to create a RAID 1 array with two 1TB drives. The drive mode is set to RAID on the Motherboard, and I was able to successfully create the RAID within the Intel Rapid Storage BIOS. Once booted into windows, in the Intel Rapid Storage Technology Window it says recognizes that the RAID is there and says the status is normal. It has been initialized through this program also (although i have read that there is no need to initialize for a RAID 1). In Disk Manager I can see my SSD that windows boots from, and 1 WD 1TB drive (There is 2 there though, but this makes me think that it sees that its a RAID) and it shows it as unallocated space. In "My Computer" the only drive i can see is my SSD. So i guess my question is what do i need to do to make Windows see the RAID in "My Computer"? This is my first RAID build so im new the the RAIDing world.
I would like to get 2 SSDs and put them into a raid array using Windows 7-64bit, but wanted to make sure I understand how to do that. The 2 SSDs will be the only drives in the system. My computer has an X58 motherboard with an ICH10R. Here is what I think is the correct procedure: Boot into the bios. Set the storage config to RAID (the other choices are IDE and AHCI) Reboot and hit Cntrl-I to get into raid menu during boot. Set up the raid array in the setup screen. Reboot to the Windows 7 install CD and install Windows Is this correct? Are there any other steps I need or tips I should be aware of?
Last year sometime, my install and all that went flawless, I put Windows 7 64 bit pro on a fresh drive, let it format and install as it wanted, zero problems. Boot drive was alone in the PC, its a WD black 320, I dont have the model or part number in front of me, but it seems to be a solid drive. The PC is a built clone, using Asus mobo and AMD dual core, spec's are in my profile if anyone needs to look that up, basically I don't see any of that mattering in my problem but there you go.added a promise RAID card last night, using an existing array from a previous build, and the system worked great and booted great once. I thought I was home free, but rebooted just to check since I have so little faith in PC's until they work twice, and sure enough I get hung at the glowing windows screen if this card is installed.I have read all I can here on this, and have been thru much troubleshooting... BIOS is fine, boot drive reads fine... the card and its fast track utility see the array fine... all those drives recognize just fine... the problem as I think today is, with the new array in place, windows can't figure out where to boot.
The old array was bootable years ago, so there is probably an MBR on it? I'm guessing a little at this point, but I used to boot to that array but went away from that years ago... since then, and I think I was on win2k back then, but adding an fresh hdd then, and since moving to XP, nothing ever cared... forward to today, Windows 7 does not like this array being in the mix, thus it hangs at the glowing window screen (the starting windows splash where the happy color balls form the win logo)remember, this was all up and running once, so that should eliminate a bunch of trial and error on bad drives, bios issues, and driver stuff... i have been thru the ringer with promise, and they swear the driver is good and is WQHL certified and all that... pulling the RAID card out lets me boot normally, so the hang up is definitely with the presence of this array the catch?? while my boot was C: to begin with, before i ever put the raid in, I put in another solo hdd... i backed up all my pictures to it.. and just before doing all this, noticed that while my C drive and E drive were all legit letter wise, looking in the disk manager, the E drive was listed as disk 0, and the C drive was disk 1... this wasn't a problem at that point, but makes me wonder why on earth the boot drive isn't device 0.
I was contemplating using a Raid 0 array as my primary C: drive with OS. I understand all the issues with that and do regular daily backups. I used to use Acronis which had no trouble with a raid array. But on this new build I was wondering if the built in backup tools would be able to image and more importantly restore my data to the array. My back up drive is not part of the array. I would guess that it would see it just fine from the OS and have no trouble creating the backup image, I am more concerned that if I had to use the rescue disk and reload the image whether or not the array would be visible to the restore disk.
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
So i have windows 7 installed on one 120g ssd and i want to take the OS and put it on a raid 0 array using two of the same 120g ssds. Whats the best way i can acconplish this?note, the ssd the os is already on will be one of the ssds used in the array
I have a 6TB raid array consisting of 2 3TB drives. I have the latest Motherboard with EFI bios. The Intel RST utility allowed me to set up this array, and it says it is bootable. I would like this to be my C: drive.
How can I get Windows 7 to install and boot from this array.
I'm trying to install Windows 7 64-bit on my brand new custom PC, using a RAID0 drive array. I already set the array in the BIOS, and the BIOS sees it. All shall be going to plan...
Nope.
The beginning of the install goes fine, I accept the Terms and all that good stuff, it's loading files, yadadada.. but when it gets to the part where it's asking me where Windows 7 is asking me what drive it should be on, nothing is there. It asks for drivers (my SB750 RAID drivers) so it can find the drives, I put in my USB flash drive with the RAID drivers (I tried both from disk and website), it tells me that no new devices could be found.
I don't think it's a problem with my physical computer, So it's either that I messed something up in the BIOS or Windows 7 is being picky on it's RAID arrays.
Running Windows 7 Ultimate x64. I have setup a partition which I transfered from on drive to another and now my boot partition is on an SSD Raid array connected to an LSI 9260 controller. If I boot the computer with the RAID Array first, the computer will just hang there. No message no nothing after the Verify DMI success message. If I setup my computer to boot from CD first and the the RAID Array second and with a bootable CD in the drive, the BIOS will display the "Press any key to boot from CD" If I don't touch anything, then windows will load just fine when the boot sequence switches to the RAID Array.
I am getting ready to set up a RAID Array but this is my first time doing anything with RAID. I know how to get into the BIOS and change settings and I know with two hard drives, I should do RAID 1. However, I just have a few questions before I do this. First off, I am an idiot and did not notice that my first hard drive I got when I built the computer has a 32 MB Cache:
Caviar Blue 1TB 7,200 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive WD10EALX - OEM
I noticed it only had a 32 MB CACHE when I went to get another one. I then asked for the version with a 64 MB CACHE (WD1002FAEX), paid for it and left. Will these two hard drives work together in RAID if they have different sized caches?
I had a successful raid 5 array setup. It was assigned to g and while I was installing ps3 media server and then java it lost it's drive assignment. It shows up under disk management but asks me to initialize it. I really don't want to do that because it will format and i will lose the data on the volume. What else can i do to get my array to show up in windows with my data intact?
in my PC there are some drives with RAID0 arrays and from little time I have bought a SSD for Operative System (Windows 7).in your opinion (on the BIOS) is it better making the Boot with SSD or with another drive with RAID0?
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
I have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
About 2 weeks ago my computer started experiencing some technical difficulties when the video card went out. The screen began to be cut up by 3 discolored bars running vertically spread out across the screen. Realizing this was a video card issue i went out and bought a new Nvidia Geforce 640 and replacing the old obsolete one. While looking for instructions online on how to properly install the new driver, i came across one that said to use this driver sweep program to wipe the driver from the system then restart and install the new software. upon using the program however i might have cleared another driver accidentally in the process. it was abbreviated ATG or something along those lines. When i finally physically installed the driver upon restart the video problems were all fixed and the graphics were back to normal. However,after bios i get a quick detecting arrays error that flashes for a fraction of a second ( i had to record it and pause it off my iphone to read the array error) and the computer automatically reboots upon getting to the windows 7 logo.
I have Win 7 Pro 64 bit installed on an ASUS P7P55D LE motherboard which supports RAID 0,1,5 and 10 using Intel Matrix Storage Technology through an on board Intel P55 chip set. The system was assembled in Nov 2009 using two Western Digital Caviar Black 750Gb drives in RAID 1 as Drive C:. (I now know from Western Digital Customer Service that I shouldnt have done that, but lets move on from there). Last December, an error message informed me the RAID array was broken and identified one of the 750 Mb drives as needing replacement. I happened to have a spare 1.5Tb WD Caviar Black at the time, so I pulled the 750Mb drive and replaced it with the 1.5Tb drive. Life was once again good. Then on July 4th (wouldnt you know) there was a repeat of the December 2011 error message telling me to replace the other original 750Gb drive. Okay so I had another 1.5Tb WD Caviar Black laying around (dont ask) and did a similar swap out. Thats when I emailed WD Customer Support asking about the 750 since their diagnostic software said the drives were fine. Thats when I learned that I should be paying lots more for enterprise quality drives if I want/need RAID. Well thats not what ASUS says in their advertising, but live and learn. All thats prologue, because my real question is whether its possible to break the hardware-based RAID 1 array and set up a Windows 7-based RAID 1 with the two 1.5Tb WD Caviar Black drives without having to reinstall Windows 7.
I had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.
Built a "super computer" with all the bells and whistles, did raid0 array OK installed Windows 7 ultimate on ssd 120GB drive.went to drive management found raid array, partitionnedit as 1 18TB drive without problem BUT when i tried to format it (quick since i suspect it may take days) and iwin sais failled to format drive.i will try to make a Loooong format and see what happens.
I've got 2 2TB hdd running in a raid0 volume setup with Intel RST. I made a flash disk for the raid drivers. Then I go ahead and start the install of Windows 7, load the raid drivers, create a 1TB partition to install Windows 7 on and have a 3TB partition for storage and such. Installs windows no problem. When i restart the system windows boot manager appears with "0xc0000225 - The boot selection failed because the device is inaccessible"If i then restart the computer, i get windows error recovery screen, if i choose Start windows normally, it boots fine. If i choose repair, it just goes back to the 0xc0000225 screen. This happens every time i restart the computer.I've tried everything i can think of, such as changing the boot order in the bios and such.
Which configuration would be better using mobo sats 2 raid or using seperate rid controller via pcie card Rosewill Rc-211 wsis3132) or should I use mobo for raid and card for extra sata w/o raid I have more drives than sata slots. How do I transfer data videos/Tv shows from existing drive to raid?
I have a problem with my Soundmax array mic on windows 7, the volume is very low and when I use mic boost the sound is of very poor quality with annoying static. Does anyone know some good drivers for this sound card that will work on windows 7 64bit?
I have no problems whatsoever with audio playback, just the microphone has problems.
L.E. After fiddling with lots and lots of drivers, I found a modified version with the new Soundmax panel, problem is although the microphone works as expected in the sound card software, in windows and other apps it still has the same problems.
M.L.E. Made it using the v6.10.02.6520 driver wich you have to mod to make it work on some ADI sound cards, more details about modding in the 3-rd post of this topic:
I am trying to format a 320 GB disk drive as single storage that was once used on a motherboard as a Raid 0 array. I can format the disk drive as NTFS via a USB cable, but when I try and connect the drive internally on the motherboard, the computer does not see it. When I go to disk managment to try and initialize hhe drive, it list the drive as a array and gives me an error. I have tried this a couple times and am at a loss as to hoe to get rid of the "Array" name disk managment says it is.
I have an OCZ Vertex 3 SSD and 2 WD caviar blue HDDs. I have them installed on an ASUS Maximus IV Gene-Z MB. I have Win 7 Home Installed on the SSD and would like to set up a RAID 1 array with the HDDs for my data storage (music, pictures, etc.). From what I understand I must do a hardware RAID setup since Win 7 Home does not support the software RAID array. The only information I could find is how to install windows on the array and not use it as a non-bootable array for data storage.
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
I put two HDDs on GA P55A-UD4P motherboard in Raid1 type array (on Intel SATA Controller) and they were working fine for quite some time (2 weeks or so). One day, after Windows started up, I noticed a blue icon on Intel RST manager and it says that the array is initializing. Will it delete the data that is stored in there already ? As far as I know, initialization is needed in Raid5 type arrays, where parity needs to be calculated. Raid1 is a pure mirror so what would be the need for initialization right now with data in the array already?
Now, I actually have the exact same OEM disk of Windows 7 Home Premium installed. I have a sister that seems to think she owns my laptop. I have considered splitting my HDD partition into 2 so that I can have my own installation and part of the drive. The problem is that if I screw something up, my sister will have a cow (it's the only place where she stores her iTunes, etc. and she's stubborn to use anything else, she wouldn't even accept it on backup). Can I also have 2 of the same OEM copies on each partition? If not, I'm Out of luck.
I am trying to get Windows 7 up-and-running on my Toshiba M200 tablet with an SSD.
The problem is that I do not have an external DVD and these machines don't allow booting from USB.
I've managed to get a fresh install onto the drive by installing it onto a partition of the old disk based drive and then copying this over using Norton Ghost. Unfortunately I cannot get this to boot, which I assume is a problem with the MBR.
I have a second machine running Windows 7, and If I mount the SSD using a USB caddy it all seems healthy and is marked as an active partition. Is there any way to get this drive booting without being able to load up the repair functions on the DVD?
I bought a computer that had Windows 7 on it, but didn't have an installation DVD. Well, I am unlucky or something, but twice over the years my Windows installation got corrupted or somesuch, now I would like to make a backup of it in case, without having to purchase a license of course. How would I do that? Do I have to download files? Insert a DVD and run a special program or something?
