I was informed today that our home computer has been freezing over the last day or so. I logged on and looked up some info on the error i was described, then perhaps fortunately, i got the vile BSOD. This is what was contained:Then it began a memory dump.It claims a device driver error, but i do not recall installing anything recently. the windows report proved less than helpful (surprise).
View 1 RepliesI'm getting pretty frequent shutdowns with the below information. When the box re-boots, the message says device driver but never can point which device driver. Can anyone have a look at this and give me some advice?
View 7 Replies View RelatedBlue screen error caused by a device or driver You received this message because a hardware device, its driver, or related software has caused a blue screen error. This type of error means the computer has shut down abruptly to protect itself from potential data corruption or loss. In this case, we were unable to detect the specific device or driver that caused the problem.
iam running windows xp....ive been having problems with my pc forever and i can never seem to work out if its bad ram or a memory issue. Anytime my pc is running for a long period of time it seems to hang and give me the blue screen, if i try to run a media program or burn a cd or anything along those lines it hangs also....What could this problem be? do i need to let someone look into my system or can it be resolved at all. Ive had every error msg i believe...it seems to always tell me its a device error when it hangs or when i reboot it gives me that msg and then reports the proble
When trying to install farstone virtual drive on a computer it reboots during the driver installation phase. After the reboot at the desktop windows says new hardware found and asks to install it. It's the offending driver, fcdabios. Windows installs it and says it was installed successfully. Then the computer spontaneously reboots again. It seems to start alright back at the desktop but again reboots after 2 minutes. The only cure is to do a restore from a norton ghost image. I sent a debug file to farstone but haven't received a reply yet.
View 2 Replies View RelatedI have a Toshiba Laptop Satellite with windows XP, Service pack 2, and always when I open a photo or see a movie with windows media player it changes the screen resolution and always came too big so I have to restart the laptop. The solution of microsoft is to update the graphic driver but when I go to the web page they don´t have an update for me, and also in the toshiba web page.
View 5 Replies View RelatedI hope somebody can help me, please excuse my lack of pc skills!I am getting BSODs every day, usually 2 or 3 when booting up pc then pc runs fine for rest of the day. BSODs have varied but typically (but not always) IRQL_NOT_LESS_OR_EQUAL with STOP: 0x0000008E or STOP: 0x0000000A. Also, in Device Manager, Ports, Communications Port (COM2) I have a yellow exclamation mark, Code 10 error.I am not sure if these issues are linked.I know it could be a Ram issue but I have run memtest86 with no errors reported.Besides I am reluctant to replace the Ram or motherboard as I wouldn't really know what I was doing.
View 8 Replies View RelatedHow do you fix BSOD and Stop 0x0000007E error?
View 1 Replies View Relatedcomputer has a BSoD, Stop error 0x00000024. Many of the guides on the Internet told me to run " chkdsk drive: /f " in Cmd. The problem is that I CANT go past the BSoD to access Cmd, even in safe mode. It is a Windows XP Home Edition.
View 2 Replies View RelatedThe computer I am working on is a Compaq Presario SR1020NX running Windows XP Home Edition. It connects to the internet via a Linksys WMP54G adapter. It tried to install Windows XP SP3 and it failed. While the update was trying to work correcting the changes it made it froze so my b/f powered it off. It rebooted just fine and he was on the internet for a little bit and then it stopped working. We recycled the modem and the router, I reset everything. Tried to uninstall and reinstall the adapter and nothing worked. I contacted Linksys and we tried to use WZC to connect to no avail. After troubleshooting a little more we determined that it had to do with the updates that were just installed on the pc. The tech suggested removing all the updates that were just installed and try again. I tried...but that is where everything went heywire. I uninstalled the first update and rebooted.....then got a blue screen flash up that said autochk program not found - skipping autocheck and then went to an endless boot cycle. I couldn't boot in safe mode, tried last known good config and nothing worked.
View 2 Replies View RelatedI have a user who is getting a blue screen that references the following stop codes;
0x000000C2
0x00000000
0x80000000
I looked around but it seemed like a lot of people's issues were resolved by replacing the memory. So here is what I did;
The laptop is an HP 6710b;
- Completely replaced the memory - BSoD still happens
- CHKDSK /F - BSoD still happens
- Latest patches removed - BSoD still happens
- take hard drive out and put into a different, identical 6710b - problem resolved.
| BIOS version is the same on both laptops
I have been receiving a bsod error lately it says BUG_CODE_USB_DRIVER I Have Done Lots Of Searches On Google But Nothing Has Helped Me Out So I Am Asking My Self. Here Are Some Pics Of My Error Report.
View 7 Replies View RelatedAn app was installed, and right after, a BSOD came up with the following error message: A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.
Technical information: *** STOP: 0x0000008E (0xC0000005, 0xBF803EF6, 0xF70917c4, 0x00000000) *** win32ksys - Address BF 803EF6 base at BF800000, DateStamp 43446a58 Beginning dump of physical memory. Physical memory dump complete. Contact your system administrator or technical support group for further assistance......
As in the title, im faced with a permanent 7B BSOD stop error message on my pavillion laptop. My current knowledge indicates that is a boot loader error, and as you may naturally expect, i am desperate to fix it! I have tried using the advanced startup options to use the last configurations which worked and safe mode, but i get the same BSOD stop error. I placed my hard disk in another laptop and it boots fine, i have even been able to log in and use it as normal. However, when i put a hard disk running a perfectly fine copy of windows xp home to my pavillion laptop, i get the same 7B stop error.
My pavillion refuses to boot from CDs as well. It seems to me the problem isnt with my hard disk and the OS version on it, but with the remaining components on my laptop...but what could be the criminal? Would anyone be able to shed some light on my problem? Of course, I will provide more details as requested.
Installed and later on uninstaller a program. After that i had to restart my computer and got the following bsod: stop: 0x0000007B (0xBACC3524, 0xC0000034, 0x00000000, 0x00000000).
View 11 Replies View RelatedA problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you seen this stop error screen, restart your computer. If this screen appears again follow these steps: Disable or uninstall any anti-virsus, disk defragmentation or back up utilities. Check your hard drive configeration, and check for any updated drivers. Run CHDSK/ F to check for hard drive corrpution, and then restart your computer. Technical Informtion: *** STOP: 0X00000024 (0X00190203, 0X86F3B848, 0XC0000102, 0X00000000)
It said all of this. I cant uninstall anything because this error comes up right after it says windows. I already tried safe mode, start from the best mode where it work and etc. It is not workin. i already tried the F8 steps, tht did not work either. and i dnt knw wat they are tlkin about when they say run CHDSK/ F. ummm yea so i need alot of help. Hopefully someone can walk me through of how to fix this. And also i do not have the window xp installtion cd or disk. I was wondering where u get tht from because when i was lookin up how u fix this problem most said u need this cd. So pretty much the basic of my problem is tht i have the BSOD and it is 0x00000024 error and i can not log on or even get to the log on part.
stop device will not run in this operating system.... I get this message at the start up of my computer and will not continue to boot up until I clear it.
View 5 Replies View RelatedMy motherboard is an ASUS P4V8X-MX with on-board audio, C-Media AC97 version CMI9761A. The latest version of the driver and operating software from the C-Media website is dated December 2004.I have two hard drives, both the exact same type (Western Digital WDC 3200JB, 320 GB), both with Windows XP Professional with Service Pack 2 installed. On my second hard drive, I continue to be able to play DVDs on any of my DVD player programs that I wish, with no problems. However, on my primary hard drive, I have run into problems. Some time ago, I don't remember anything about what might have caused it, both Windows Media Player 11 and InterActual Player 2.6 (http://www.interactual.com/) stopped playing my DVD's. I could still use InterVideo WinDVD or my ATI Radeon X700's DVD playing software, with no problems, but WMP and IAP stopped playing them. WMP would give me an error that, when I clicked "Web help," said it was related to my Sound driver. I went to Windows Update and downloaded the following update:
Windows XP C Media Electronics Incorporation - Sound - C-Media AC97 Audio Device Tuesday, August 21, 2007 Windows Update.But this only made the problem worse, not better-- now when I try to use WMP or IAP to play a DVD, my computer screen just up and suddenly goes dark and I hear the unmistakeable sound of my computer simply up and shutting down, and then it does a total system reboot. After the reboot I get a popup saying the computer has recovered from a Stop Error, caused when a Device Driver suddenly "stops" the operating system.This is a very serious problem because a number of my DVD's are specially optimized to work with InterActual Player and automatically start it up when I put the DVD in the drive. If I try to uninstall the program, then the next time I put one of those DVD's in the drive it absolutely absolutely ***ABSOLUTELY*** forces my computer to reinstall the software immediately.
I have been getting BSOD for about 2 months now and always when i play a game especially bf2 and cod
after every BSOD it comes up device driver error but all drivers are fine,I have changed RAM,PSU and mobo after last time i was pulling my hair out and now its started doing it again after nearly 2 weeks
my system is as follows:
AMD A64 3200(winchester)skt 939
MSI neo 2 platinum NF3 ultra mobo
Giel pc 4000 ultra 2x512
Radeon X850 XT PE (agp)
I just got a blue screen with the following information:STOP: 0x0000008E (0xC0000005, 0x805677C4, 0xEF8C7D40, 0x00000000)I'm currently running Windows File Protection...but I don't know if there is anything else I should do.
View 2 Replies View RelatedI was working on my computer, Windows 2000 Pro.I was moving my foot under the desk and accidentally switched off the surge protector.I turned the protector back on and restarted my computer.I get a royal blue screen that says Stop Error.Inaccessible Boot Device.None of the F8 options work for restart, they all say the same thing.I really don't want to have to reformat.
View 6 Replies View RelatedWhen I want to install certain programs, there is a set of error messages that makes the installation fail.If I push "ignore" then this message appears:
"c:Windowssystem32autoexec.nt. The system file is not suitable for running ms-dos and microsoft windows applications. Choose 'close' to terminate the application." I have a feeling that this is caused by a Norton antivirus program I installed couple years ago that I had a heck of a time removing. Could there be a chance that some parts of the program is still lingering to cause this? I've been having this problem for the longest times and threw away a bunch of software.
This happens when I watch videos, or do anything that has to do with videos such as windows movie maker or use media player, anyways, I keep getting this page http://oca.microsoft.com/en/response...&SID=10.My question is, how do I find out which device driver is causing the error so I will stop getting to many unexpected restarts/freezes?
View 14 Replies View RelatedEven after a fresh re-install of XP the sound driver install causes the machine to crash. No matter what I do. I have most of the files loaded except for the multimedia controller. each time I try to update it , the machine crashes.Not sure if it matters, all high priority updates are done
View 3 Replies View RelatedInsert any USB device to this computer, Computer keeps restarting and it wont stop doing that until I remove the usb device. I tried with all the usb ports on this computer and problem is the same. Even by hooking up a usb keyboard or mouse, computer wont get to the login screen. it keeps on restarting. It wont even go into 'safe mode'.Anyone have any clue whats going on and the solution to fix it?
View 2 Replies View RelatedSTOP 0x00000050 (0x8CCC1345, 0x0000001, 0x808A65A1, 0x00000000) These both happen when installing windows, either when at 95% of copying files or when booting into windows.
View 7 Replies View RelatedI installed windows XP on a system that I am servicing.The floppy drive wasnt installed correctly in the first place, and windows XP kept crashing to a blue screen, then restarting.I unchecked the Reboot automatically after system failure checkbox and recorded the error.Its written below..It doesnt happen at any specific time, or when a specific application is open..It did it after the first fresh install, so i did ANOTHER fresh Install, and its doing it again.
View 7 Replies View RelatedI seem to have bad luck with multiple partitions on one drive. I have a 160 gb hdd that was partitoned with one approx 137gb partition with windows xp. It was working fine. I decided to partition the remaining space which was something like 25gb. I did it from windows xp in the disk managment snap-in. It worked fine until I formatted the new 25gb partition and assigned the page file to this drive. I had not rebooted before formatting the new drive and I believe the format is what screwed up the drive. I have tried to chkdsk /r but it took forever and then crashed. I believe windows improperly sized the partition over part of the original C partition. I really hate logical drives. I always seem to have some sort of data loss with them..
View 13 Replies View RelatedSometimes after playing a game like Halo I get a blue screen saying that to prevent hardware damage, Windows must be shut down. Something about Intel's GMA driver igx32.dll or something. There's also no option to shut down my computer, I have to press and hold my power button.
View 4 Replies View RelatedIt seems you guys know quite a lot more then I do about windows.I was hoping maybe someone knows more than I
I'm having these randomly occuring BSOD's mostly at night time,no intensive apps working,except some p2p progys.I have ruled out RAM,VGA and I think PSU too,and i guess it has something to do with networking.I have some memory dumps I will attach,.I have only these 2 because somehow windows didnt make any more,dont know why though.
my inlaws have a gateway with XP media on it. they told me that the machine said it was updating and going to reboot. after that it never rebooted. when they turned it on they got a reboot loop going. when i looked at the error msg it was the 7e stop error. with nothing else i did a search but just could not find anything like this. i can not boot into safe mode or normal mode. i have done a chkdsk /r /p several times but still no go. i have taken the HDD and was able to clone it with acronis to a larger drive. i put the HDD in a different pc and same thing.
View 8 Replies View RelatedI am getting a BSOD and the error says: PAGE_FAULT_IN_NONPAGED_AREA STOP: 0X00000050 (0X81000078, 0X00000000, OXF9E129BD, 0X00000002) spooldr.sys - address f9e129bd base at f9e11000, datestamp 469e788d I tested to see what drivers are not digitally signed because I read somewhere to check that and it said that the omci.sys and tcpip.sys are not digitally signed. I am testing all the hardware as we speak with PC-CHECK, the RAM seemed to pass all the tests. I can log in to safe mode and I tried restoring to a previous date and it worked for a while. I was able to uninstall the McAfee Antivirus which I thought might be the problem, but still BSOD...
View 14 Replies View Related