Windows 7 Failed To Boot After Installing New Usb Mouse
Jul 15, 2012
i just bought this new mouse razer lachesis 5600..when i plugged in the mouse, install the driver, it went ok, no problems at all.the problems start when i reboot, the screen just freeze at the motherboard screen (MSI 890fxa-gd70)..i remember reading from this forum, to try unplugged all usb device, i did that, and my pc can boot normally.. mouse also have no trouble if i plugged it after i got on windows.. but everytime i reboot with mouse plugged in, it always freeze at the mobo screen..or i should unplugged my mouse everytime i want to reboot?
View 9 Replies
ADVERTISEMENT
May 12, 2009
I just installed Windows 7 as a dual boot with my XPsp3. Now my Logitech Revolution VX mouse has lost all its special functions, and the Setpoint software in unable to work properly.
Any thoughts? The same thing happened when I set up Ubuntu as a dual boot - finally removed the linux.
View 0 Replies
View Related
Sep 6, 2012
I have a HP Probook 4530swith Windows 7 Home Premium 64 bit. When I turn on the PC the windows does'nt start and give a option of starting windows manually, which does'nt work, and repair windows. Repairing windows with windows 7I then decided to reinstall windows 7, but while installing, on the select disk page, it shows a error saying no drives found.I then performed a Hard Disk Test which resulted in failure saying:Failure ID : UC7WX0-5NB67S-XD6V5G-60TF03
View 2 Replies
View Related
Mar 10, 2012
I had Win XP on 1 HDD & installed Win 7 on a different HDD. I think I accidentally did a dual boot install because Win 7 won't boot without the the XP disk connected to the motherboard.
That was fine until my XP drive died yesterday. Now Win 7 won't boot. The first time I tried to repair, Win 7 was not even seen. so I booted into diskpart and made the partition active. Now it could be seen as an OS.
Then I did a startup repair. It did whatever it does & when it was finished I restarted the pc but it didn't boot I went back to diskpart and confirmed the partition was active. I went back startup repair and tried again.
This time it said it could not detect a problem, but it still will not boot. What else can I do? My pc is homebuilt. Right now I have the 1 sata drive, 2.53 ghz cpu, 4gb ram, onboard video & sound
View 5 Replies
View Related
Jul 19, 2012
Ever since installing Windows 7 (64 bits) my mouse stutters. Skipping every now and then, staying in one position while I move the mouse, etc. I do a lot of photo editing and it's really annoying and makes my work almost impossible. [code]
View 7 Replies
View Related
Oct 14, 2012
I tried installing Windows 7 64 bit OEM on a fresh hard drive but it kept crashing and now when I try booting the system seems to think Windows is installed saying ''Windows failed to start'' in boot manager. I even tried loading the computer up with a different hard drive but it STILL says that!
View 1 Replies
View Related
Aug 31, 2012
I bought a SSD, installed it, installed Windows 7 Ultimate. Got into windows and everything was fantastic. Installed all the windows updates, video card drivers, ect... Then rebooted the computer and lo and behold, it doesn't recognize the SSD as a valid boot device anymore. Assuming that the install corrupted somehow, I decided to run startup repair on the Windows 7 disk. However once the disk gets past "Windows is loading files" all the lights on my mouse and keyboard shut off and they stop working. However up until that point they work fine, if I go into BIOS they work no problem. I have no idea what the issue is... I literally JUST used this same disk to install windows 7 and had no issues less than 30 minutes ago... The only advice I've been able to find thus far has been to ensure that legacy USB settings are enabled, and they are. Also, if I boot into windows on a different drive that has the OS installed my mouse and keyboard work just fine in windows as well. As it stands now I cannot fix my windows install or even reinstall windows...However up until that point they work fine, if I go into BIOS they work no problem. I have no idea what the issue is..
View 9 Replies
View Related
Dec 31, 2011
I used my Turtle Beach Headset while playing a game and since then the computer has started saying i have two mice connected to my computer. The problem is that since its reading two mice the one i have been using forever has stopped working right.ouble Click is disabled and it moves extremely fast. I go to disable the HID Mouse and everything is working fine again. But when the computer restarts it seems to reinitalize the HID Mouse. So i uninstalled the driver for it. Next reboot it was back again and this time the headset wasnt even plugged in. I am not getting any error messages in my device manager but i cant seem to get the HID mouse to disappear. Whenever i plug anything into the USB port even if its a Thumb drive the mouse comes back.
View 2 Replies
View Related
Jan 15, 2012
I tried to install a One Touch 9320 USB Scanner and received "adding printer driver failed". The software is out there but I cannot connect make a connection to the scanner. All the wires are connected.
View 9 Replies
View Related
Jan 13, 2012
have beeen reading through this amazing forum for the past couple of days trying to get my Dell 1545 working again, i have tried to reinstall the OS from a disc that came with the lpatop, to no availi created a system restore disk from the machine i'm writing this on....still to no avail....i can get into the setup menu's but like many others i can't get any further, I don't know how to get into the BIOS menu (and to be honest wouldn't know what to do if I did
View 9 Replies
View Related
Nov 20, 2012
I have a computer I am trying to refurbish. The old hard drive failed. I purchased a new hard drive. The CD/DVD player on the computer does not work, but I am able to boot from a USB. I was able to install Ubuntu from USB with no problems and now have a new copy of windows 7, 32 bit (computer is also 32 bit). I have tried to boot from the windows copy on the USB drive using many different tutorials as well as using the windows USB/DVD download tool. Each time I boot from the usb stick, a screen comes up that says windows failed to start. It says it may be due to a hardware problem. All other solutions to this involve using the recovery CDs or partition which I am not able to because the CD/DVD drive is broken, and I would like to not have to buy another one.
View 3 Replies
View Related
Jul 25, 2012
I made the naive mistake of trying to upgrade from a Biostar TH67+ MB to a MSI Z77A-GD65 MB using my existing Windows install. After I installed the new MB and the new drivers within Win 7 Pro 64 bit, the machine wouldn't boot. So I reverted to the Biostar MB and it still won't boot. I have tried Safe Mode (which just hangs) and I have run Startup Repair several times. How I can further troubleshoot/repair the boot?
View 1 Replies
View Related
Mar 21, 2011
I'm currently running a WD 500g with Windows 7 Ultimate x64 and a Seagate 250g with Windows XP Home Edition. I recently changed my BIOS boot order from the WD to the Seagate to see if I could still run XP. Turns out I can. My problem is that now I can't load Windows 7 back up on the other hard disk.Bear in mind that I have no other OS' loaded on any other partitions, and these HDDs are separate. The Seagate is IDE and the WD is Sata.I can load perfectly fine if I set the Seagate to load, but I get the infamous "Bootmgr is missing, Press Ctrl Alt Delete to restart" error msg when I try to boot win7.
I'm running a custom PC with a Gigabyte GA-X58A-UD3R mobo
nVidia GeForce GTS450
Seagate 250g Windows XP
Western Digital 500g Windows 7
6g RAM
i7 940 processor
View 1 Replies
View Related
Jun 8, 2012
I upgraded to Win 7 Ultimate from Win XP Pro after my OEM disk picked up a few more scratches than it needed.During a re-installation it partially installed the windows XP setup with an error message of 'HAL.DLL' missing.I believe the residual setup loader is causing problemS.My PC insists on trying to boot from CD/DVD regardless of what I select.If I select boot from CD/DVD with my new Windows 7 disk I get the SAME message as if I didn't select boot from DC/DVD: Windows failed to start. This could be from a recent hardware or software change.
1.Please insert your windows install disk and click restart
2.Change language setting and click next.
3.Click repair... etc.
If you don't have the disk contact admin....ect.
File$LDR$
Status 0xc000000f
info: Selected entry not added/ application is missing or corrupt.
Enter Escape.
Escape = reboot to error listed above...
Enter = OS choice menu with:
1. 'windows 7'
2 'older verion of windows'
I select the ' older version' and the system gives me the same listed above error...I select 'windows 7' and, well.... here I am, posting this thread from my PC, Windows 7, updated, gageted and all running smoothly...Hibernate sometimes boots and sometimes shows the same error.....Start menu 'Shut down' and 'Restart' also don't work on the odd occasion....I researched and downloaded EasyBCD to delete the 'older version of windows' but it appears to have only 'deleted' it from Windows 7's 'eyes' because ultimately the thing is still showing on my OS choice menu and is evidently causing a few hiccups.
View 1 Replies
View Related
Feb 8, 2013
Long ago i updated my bluetooth adapter driver, and the caused malfunction. I downloaded the driver from Dell Support website (apparently there are 3 under 'Network', and i get a lucky shot) and the bluetooth is fucntioning once again. however i checked through the device manager and found '!' marks on Bluetooth Peripheral Device. something is not right. Recent windows update (automatically) has failed to install over and over again, hence prompting to redownload the same update every time i turn on the laptop. Specifically, its is 'security update for the .NET Framework 4 on Windows XP, Windows Server 2003, Windows Vista, Windows Server 2008, Windows 7, and Windows Server 2008 R2: January 8, 2013 (KB2742595)'.. There is another update coming (also tagged as Important) but come to fail as well. So currently there is 2 pending updates.While im having these problem, the boot time has increases noticeably. Long black screen appears before the login page turn up. Some says this is related to device/driver error. im not sure myself. Very recently i have my Avast Antivirus not working (turned off) and every time i ask it to turn on or resume, nothing happens. It remain not-functioning and so, i uninstall Avast and adopt AVG Antivirus. i think this is around when i was installing the bluetooth driver from Dell.
View 2 Replies
View Related
Nov 24, 2012
A new hard drive has been installed on my laptop. I tried to install windows 7 and it failed. I am missing the master boot manager. is there free software to fix this problem that I can burn to a dvd or usb flash drive?
View 2 Replies
View Related
Nov 25, 2012
how do you disable this warning failed to connect to a window service
View 1 Replies
View Related
Apr 6, 2012
I installed opensuse 12.1 on dual boot along with my other windows 7 installation. Installation of opensuse is successful and i can use it. But when I tried to use windows 7 on grub, it says bootmgr is missing. I've already encountered this problem a long time ago so i tried to use bootrec /fixmbr, bootrec /rebuildbcd and bootrec /fixboot in the recovery console in the windows 7 DVD. Rebuildbcd and fixboot did not work and it said something like it cannot find my windows installation. I also tried bootrec /scanos, it returned a windows installation on D:\Windows but my windows is in drive C. I think this has something to do with me messing up the active partition in disk management a month ago but i already fixed it by setting the active partition to the system reserved partition. Only fixmbr is successful, but now i can't boot on any OS because it says: Missing operating system.I also tried bcdboot C:\Windows but it failed with a message that goes like: Failure when attempting to copy boot information..
View 2 Replies
View Related
Dec 3, 2010
I can't get Win 7 to boot after setting up dual boot (Ubuntu 10.10) on my GF's laptop. I'll describe the problem and everything that has been tried so far. REALLY hoping somebody has an idea, I'm getting desperate.I installed Ubuntu last night via the Live CD. Used the Live version to install alongside Windows and partition the drive, install Grub, etc. At reboot, after POST it would just go to a black screen with a flashing cursor. I could only run off the live CD. A forum member determined the Grub was trying to load from the wrong partition. We changed that and voila! Grub now loads properly. I can boot into Ubunto via Grub with zero problems. HOWEVER: when I try to boot into Win 7 from Grub, it just locks at the same flashing cursor of death screen. The 7 partition is till intact, I can see and access all the files on the 7 partition from within Ubuntu, however 7 will not boot. I have tried downloading and burning the Win 7 repair disk and doing all of the following,Running the automatic Start Up Repair - several times. All it does is remove Grub, but booting still goes to the flashing cursor and I have to reinstall Grub again to be able to do anything after POST.I have used the command prompt to run "bootsect /nt60 SYS /mbr". Has the same effect as above.I have used all the bootsec.exe /fixmbr, /fixboot, and /rebuildBCD commands. Again, all have the same effect and I have to reinstall Grub to get anywhere.I don't have an installation disk to try and just do a repair install because Asus apparently doesn't feel that I would need one of these. All I have is the recovery disks from the Asus AIRecovery application that want to just re-format the entire drive and start over. This isn't an option. It's my GF's laptop (mine gave up the ghost last week) and we both have WAY too much highly important data on here. Not to mention she would castrate me . Now from all my research the only other thing I've come across that sounds possible is that the boot flag needs to be set to a different partition. Somebody had a somewhat similar problem and it turned out the way Dell set up the system the boot flag had to be moved to a recovery partition and it worked fine. I'm wondering if Asus has something similar going on, but I can't figure out how to move the boot flag. I'm going on 12 straight hours of working on this now
View 9 Replies
View Related
Jul 18, 2012
I've been trying to change the motherboard and cpu in my current computer. After hooking everything up, the computer runs till the windows 7 loading screen, then stalls and restarts. Upon restart I'm brought to the "windows has failed to start" message and attempting to repair through that yields no results. I hooked my old parts back up to make sure the hard drive was still good and it is. With the old parts everything boots normally.
The new parts I'm putting in are;
-AMD fx 6 core 3.3ghz processor
-Asus M5A97 motherboard
Problem Event Name: Startuprepairoffline
problem signature 1: 6.1.7600.16385
problem signature 2: 6.1.7600.16385
problem signature 3: unknown
problem signature 4: 21200975
problem signature 5: autofailover
problem signature 6: 2
problem signature 7: bad driver
OS Version: 6.1.7600.2.0.0.256.1
Local ID: 1033
View 4 Replies
View Related
Nov 21, 2012
I had a dual boot with Windows 7 and Win8. I wanted to remove Win8 cause I was bored and didn't need it. I did everything right.
Dual Boot - Delete OS
But the boot manager failed. When I restarted I got an error saying that their is some invalid information. I didn't have the Win 7 disc, so I put the Win 8 disc and installed it in the partition that had win 8 before, hoping that it would recognized Win 7. But hasn't. So now I have a partition of Win 7 but it is not getting recognized.
View 1 Replies
View Related
Sep 14, 2012
So it all started last night. My computer was unresponsive, and after clicking "shut down" a few times to no avail, I decided to do a hard reset. I didn't think anything would happen, but afterwards it just wouldn't boot back up. It goes to the windows logo and stays there. I don't get any errors, it just hangs there. I have tried many things, so far nothing has worked.
I have tried booting into safe mode. This does not work, it gets stuck at classpnp.sys and stays there. I have tried booting from the windows 7 disc. This does not work, after it loads the disc it will hang at a black screen. I have tried switching from IDE to AHCI. This has worked, but not fixed the problem. When booting into safe mode it will crash instead of hanging.
When booting from the windows 7 disc I can almost reinstall windows, however I get the error "Windows could not format a partition on disk 1. The error occurred while preparing the partition selected for installation. Error code 0x80070057." When attempting to restore windows to a restore point I get the error "The system image restore failed. Error details: Windows backup failed to read from the recovery volume. (0x8078002F)"
I have tried connecting the SSD to a different windows 7 computer in a attempt to reformat it, however just plugging it in would give the same problem to that computer. So, is my SSD toast? Did I mess it up beyond repair? Now system repair will not hang on IDE, but still gives me the same errors. Also, now it says missing operating system. Not sure how that happened.
View 6 Replies
View Related
May 6, 2011
I just purchased a Microsoft Wireless Media Desktop 1000 keyboard and mouse. The first thing the instructions tell you to do is install the software. Should I install the software while I have my current USB keyboard and mouse plugged in?
View 9 Replies
View Related
Jan 21, 2012
I have a Dell Inspiron 1545 (2.5 years old). All my data is backed up so I have no concerns about recoverying data.First, the laptop crashed and ran several chkdsk on start up. I froze several times during this. It said it had fixed some errors then started up again.This time it wanted to do start up repair. Same thing kept happening, froze at least twenty times during this. Eventually it gave me the blue screen of death.
'Technical information
*** STOP: 0x000000F4 (0x0000000000000003, 0xFFFFFA8004C1D260, 0xFFFFFA8004C1D498, 0xFFFFF8000130DDA0)'
This repeated several times. I ran the diagnostics and it told me the hard drive could not be found (error code 0146, 2000-0146). Essentially, it's a Dell laptop (I know) and I am not bothered about recovering the hard drive.I would, however, like to install Windows 7, or alternatively Linux, onto my external hard drive. But I just can't seem to get it to work.I have extracted a Linux iso to the external hard drive I want to install on, onto a cd, onto a FAT32 8gb usb stick, but it has given me the bootmgr is missing error every time. I have tried it with the interal HDD in and removed.I am no longer concerned about the internal HDD, i can use it for a door stop for all I am concerned, I just want to load ANY os onto my external hard drive so I can get the laptop working.
View 9 Replies
View Related
Apr 5, 2012
I have a pc that has been running windows 7 pro fine for a couple of years. Today it wont boot stopping with the message: "Windows failed to start.A recent hardware or software change might be the cause."
To fix the problem:
1.Insert windows installation disc and restart your computer
2.Choose your language settings and then click "next"
3.Click "repair your computer".
If you do not have this disc contact your system administrator or computer manufacturer for assistance.
Status: 0xc000000e
Info: The boot selection failed because a required device is inaccessible.
This machine has only one dvd drive and one hdd. I have checked the boot list in the bios settings and the cd drive is first then the hdd second. If I insert the windows 7 cd and press any key to boot from cd when prompted I still end up at the "windows failed to start " screen. At this point I have the option to select "Launch startup repair" or "start windows normally" but I cant select them, the machine just counts down and continues to try to launch startup repair and fails with the 0xc000000e error.
View 8 Replies
View Related
Jan 8, 2011
I am not able to run recovery on by laptop. When I try to run recovery from hard drive or even booting system from DVD ROM using recovery discs I get the following error:
Status: 0xc0000225
Info: The boot selection failed because a required device is inaccessible.
My system is HP pavilion dv6 2150us. My hard drive is dynamic (someone told me that this error is because of dynamic hard drive). Will I have to convert dynamic hard drive to basic to run recovery? Or is there another way around?
View 9 Replies
View Related
Feb 20, 2012
I have a Toshiba Satellite A505-S69803; serial number Y9340538Q, with Windows 7, 500Gb HDD at 5400rpm and 4Gb RAM... I think that's all correct.Anyway, long story short, I got a b!tch of a virus, which apparantly was doing all sorts of nasty things to the explorer.exe file in particular. So I backed up all my important stuff: files, Uni work, writings, music and photos etc onto an external hard-drive and went about restoring the laptop to out-of-box factory settings by making the Windows 7 Recovery Media Discs. But when I try to use the discs I get told after about 30 minutes The Toshiba Recovery Wizard "Can't read from the source file or disk: PREINST5.SW5" with options to: Try Again (The same thing happens), or Skip (Same message again), or Cancel (in which case I'm back where I started).After the Recovery Wizard failed I chose the option to erase the hard-drive; it then appeared that when I turn on the laptop as normal I was told <Error>: F3-F200-0002 and the Recovery Media Disks still refuse to work.Now, if I turn on the laptop as normal a message telling me to insert the installation disc, choose language and click "repair your computer". So I put in the recovery disc and get the same message.
Toshiba can't help as my A505 is an American model in Britain and out of warranty anyway. Europe Toshiba HQ don't supply the recovery media for the A505 and the American based Toshiba aren't allowed to send the Recovery Media to Europe; so apparantly I get no help from them. And Microsoft can't help me because my laptop was purchased with everything pre-installed so the codes associated with my Windows and Office are comletely irrelevent.I have been told that I need to purchase a compeltely new hard-drive and purchase Windows 7 brand new to get my laptop back up and running. Purchasing a new OS isn't too much of an issue because I can just get XP for a tenner, validate it with Microsoft and then get a student upgrade onto W7-Ult for �60. So �70 in total, I'm fine with that. But do I need a new hard-drive too? Or can I rescue everything I already had?
View 3 Replies
View Related
Mar 14, 2011
I am running a desktop with Windows 7 Pro 32-bit. When I first power it on the normal BIOS posts and then Starting Windows just hangs, no 4 colored orbs that turn into the Windows logo. I can hit the reset button and it boots and runs fine. I have tried the Launch Startup Repair after the reset button but doesn't seam to do anything
View 1 Replies
View Related
Feb 13, 2013
I've recently purchased a used A665-3DV6 Toshiba Satellite Laptop. It had the BIOS password problem. So I've jumped the CMOS and cleared the password. I've initiated the "out of box state" and it went through the whole process. When it was finished I shut down the computer. Then the next morning I booted the computer up and it stated "HDD Boot Failed". I tried running Factory reset again but there is only a blinking cursor on the top left hand corner of the screen.
View 3 Replies
View Related
Feb 2, 2013
I just finished putting my computer together, and i'm installing OEM Windows 7 64-bit from the disc. after windows loads files, i get a black screen and error message that says: "Windows failed to start. a recent hardware or software change may be the cause. to fix the problem, then it gives me the repair computer steps. it also says
File: windowssystem32
toskrnl.exe
Status: 0xc0000098
Info: windows failed to load because the kernel is missing or corrupt."
I don't know what to do because i can't access windows at all, is there something i can do in BIOS to fix this?
GIGABYTE 970A DS3
AMD FX-6100
XFX Radeon HD 7850
Crucial Ballistics (2x4)
View 2 Replies
View Related
Jan 10, 2010
I have an HDD hooked up to an MSI MOBO using a sata cable, I am trying to upgrade vista 32 bit to a windows 7 64 bit because I have 8 gigs of ocz ddr2 ram and other upgrade I have done over the years, plus I am game hard. I turn on the comp, boot from cd/dvd. the windows 7 thing boots up and then it goes to a blue screen with flowers and stuff on it. And all I see is my mouse and that it.
View 9 Replies
View Related
