I just purchased a new 10,000 RPM VelociRaptor drive and I'm going to use it as my OS drive. Is it possible to set up a RAID 0 with my current drive (hitachi 1TB 7200RPM) without having to format it?
View 7 RepliesI had an existing properly working system consisting of a SSD 64GB for my OS and a Raid1 config with two 1TB drives for data. My SSD ended up being to small as certain programs do not let me remap content to a separate drive. I have upgraded (swapped out) to a 240GB SSD reinstalled windows on it and windows does not see my raid1 in disk management, nor does it see my two monitors or my connection to my router. It was my understanding I could just swap out the SSD's and reinstall windows and it would see everything.
View 4 Replies View RelatedBiggest bottleneck in my system right now is my boot drive, which is a WD velociraptor. I want to change this for dual 120GB SSD's in Raid 0 configuration. Can anyone walk me through the steps to copy over the existing Win7 64 install onto the SSD's, I dont want to have to load everything again
View 3 Replies View RelatedIam unable to run disk check from command prompt, after trying to run dskdsk tells me, The type of file is NTFS, Then cannot lock current drive, Then Windows cannot run disk checking on this Volume because it is write protected, have checked in bios no write protected no hiar left
View 3 Replies View RelatedI was wondering if I can use existing ssd (loaded with Win 7 and all current drivers) for a new build: new mobo, cpu and ram.Both will be x64 Guess I`m just lazy for not wanting to do another clean install
View 6 Replies View RelatedI am about to purchase a ssd for my pc and was wondering if there is a way to simply transfer windows to the ssd from my current spinning drive
View 3 Replies View RelatedOne of my external drives (WD) appeared a warning in SMART status:
C5 Current Pending Sector Count
Current = 200
Worst = 200
Threshold = 0
Raw values = 1
If this is repairable problem, what is the best tool to repair this?
How do you reset (clear) all current USB drive letter assignments? As a result of changing my external USB Hub controller from a CyberPower CP-H720P (USB 2.0 7-Port Hub w/Power Adapter) to a SIIG 06-0960A (USB 3.0 w/3-Ports & USB 2.0 w/3-Ports plus Card Reader w/Power Adapter), all of my original external USB drive letters were changed. The following are my Original and New USB external device drive letters: F changed to O � Port 7 Hub 3 � Patriot Memory (16GB USB 2.0 Memory) G changed to N � Port 2 Hub 4 � Desktop (Seagate USB 2.0) H changed to M � Port 1 Hub 4 � Free Agent Desktop (Seagate USB 2.0) I changed to K � Port 4 Hub 3 � MyBook 1130 (Western Digital USB 3.0) J changed to L � Port 3 Hub 3 � MyBook 1140 (Western Digital USB 3.0) I need to know what steps I must perform to clear (reset) my current USB drive letter assignments so that I can begin anew starting with the first available drive letter, drive letter �F�.
View 2 Replies View RelatedI recently built a computer with only one drive, I was wondering if it is possible to install another one and have them runing on raid 0 or do you suggest another type of raid maybe with 3 drives.
I have an asus mobo p5q3 so I can use Drive Xpert technology but a lot of reviews says that the speed of the drives is split in two when using these 2 sata connection (white and orange).
I am doing a quick windows build here on a couple of computers and want to RAID 1 the windows C drive. The motherboard i got for them does not support RAID (I kinda figured it would). So now i was thinking of just doing a software RAID in windows. I got the C drive to mirror each other in disk management but the issue seems to be booting. When the computer starts it asks which hard drive i want to boot from and when i simulate hard drive failure the boot manager doesn't come up at all and i am stuck with the no boot device error. My guessing is that there is something on the 100MB system partition that isn't copying over.
View 5 Replies View Related until recently I had an XP PC with a single main OS IDE HD. To backup I performed monthly an Acronis clone to an identical 2nd IDE HD that I bought for this purpose. Easy.
Now I have a Windows 7 PC with two identical SSD's in RAID0 as main OS drive and a 2nd internal HD. I would like to perform a backup of this system so that I can later restore it to any HD configuration I choose (for example a single SSD, or a single HD, etc). Is this possible or the restore will need to be done to the same original configuration (two SSD's in RAID0+2nd int HD)? What would be the simplest software that will accomplish this?
My PC is currently using a single RAID 0 drive that contains my Windows install and all my data in a single partition C: (I'm well backed up so happy with the risk of RAID0)
The RAID0 drive is setup by my motherboard controller so Windows just sees the one drive.
I am thinking of adding an separate drive for windows, hopefully an SSD. I would like to do a fresh install of Windows 7 on the new disk then rename the old RAID0 drive to something different such as D: . Then reorganise it into just a data disk.
My question is.. will the new Windows 7 installation just see the old RAID0 disk as another disk? I know this would work witha normal disk, but does RAID0 transfer over to a new installation ok?
Just wondering what or if I could move an xp backup onto a raid 0 drive. I did setup the drives in raid in the bios, and they show as raid. I booted into my marcium backup and ran my xp backup onto the drive, that showed in marcium as a raid 0 drive. When I booted, which went fine, into xp it shows in disk management as raid 0. But the problem is, it shows two drives, together and the 2nd drive as being un partitioned. Therefore I'm only running on one drive. Is this fixable, or do I need a clean install?
View 2 Replies View RelatedI have an HTPC that I've had for about 4 years now. Today when I booted it up it went into an infinite loop with the 'Startup Repair Utility" where it would just sit there claiming to be repairing the drive but never actually completing or providing a notification of the issues (typical Microsoft troubleshooting). Anyway, I finally was able to get into the advanced settings of the utility and get to a command prompt and see what was going on.
1)The previous RAID 1 configuration was setup as the main C: drive with the OS and also where I had all our music stored. But now during the boot sequence the bios startup it flashes in red complaining about the RAID array having degraded and when I finally got into a command prompt it was no longer mapped to C:, the two drives in the array were mapping independently as drive E: and F: respectively (the DVD-ROM is the D: drive).
2)My first concern was to get my music off it so I plugged in an external USB drive and went into command prompt and tried to xcopy from E:, it started to copy then failed catastrophically with a weird error so that would appear to be the bad drive. I then tried the same thing on drive F: (the mirror) and its cranking along nicely copying all my music over. My fingers are crossed but I suspect I'll be OK, its unlikely to get two drive failures in the same array at the exact same time
Once I get my data off the good drive how should I proceed? I assume I need to get a new duplicate drive installed and then can I not rebuild the RAID array from the good drive? I've never done this before, the machine came built for me so I'm not familiar how it is setup. What I do know is that it has a 'RAID utility' you can jump into at boot up by hitting F10.
I'm trying to install Windows 7 64-bit on my brand new custom PC, using a RAID0 drive array. I already set the array in the BIOS, and the BIOS sees it. All shall be going to plan...
Nope.
The beginning of the install goes fine, I accept the Terms and all that good stuff, it's loading files, yadadada.. but when it gets to the part where it's asking me where Windows 7 is asking me what drive it should be on, nothing is there. It asks for drivers (my SB750 RAID drivers) so it can find the drives, I put in my USB flash drive with the RAID drivers (I tried both from disk and website), it tells me that no new devices could be found.
I don't think it's a problem with my physical computer, So it's either that I messed something up in the BIOS or Windows 7 is being picky on it's RAID arrays.
I am about to reformat my hard drive, long story as to why, but I am starting from scratch. I know how to install windows, drivers etc. But one thing I am not sure about is configuring the RAID, as I wasn't the one who did it when we installed everything. I am asunming that when I reformat the RAID will need to be reconfigured? I have RAID 5 with three hard drives, each 500 GB. I have a program called Intel Rapid Storage Technology that "manages" the hard drives,but if I am correct I have to set up RAID before installing windows. How to configure the RAID the same way I currently have it? This is a homebuilt comp, i7 930 2.8 ghz, 6 GB RAM, Windows 7 Pro 64-bit, Gigabyte motherboard...
View 1 Replies View RelatedMy Laptop came with Raid 0 over 2 one terrabyte harddisks. Last week i started getting Drive 1 at risk message. I looked it up and it turns out that this message occurs some time before your drive fails.I did a Full computer backup using windows Back up utility using an external Hard drive. Now I'm going to buy a new internal Hard drive to replace the faulty one.What are the steps i have to do to back up properly?After some search,I learned that:
1_ Backup everything.
2_ Replace Faulty drive.
3_ Rebuild Raid 0 array.
4_ Restore the system image.
Does the new internal Hard drive have to be the same brand/type/size as the old Faulty hard drive? Also I've never used Raid, so how do i recreate a new raid 0 array ? From Bios ? Should i create a repair disk too ? or would Windows dvd work?
RAID-1 DRIVE PULL OUT TO TRANSFER ...
I have a pair of mirrored RAID-1 drives (these have been removed and sitting as is for about 6months or so)
There is no important data on this that im concerned about preserving.
What i want to do is reformat them into 2 separate single storage HDD'safter installing them into my new system. or will it mess up my new system?
I installed a Rosewell RC-217 Raid card (Silicon Image Sil 3124 SoftRaid 5 Controller-- in Device Manager). The card installed well in Windows 7 64 bit. No problems in device manager.The problem starts when i plug the drive in then rebooted. The boot stops at the 'Starting Window' and hangs. If i boot into windows then plug the drive in all work well. Windows sees the drive and i gave it a drive letter. works great.Problem is i can't boot my system without un-pluging the drive.
View 6 Replies View RelatedI am installing Windows 7 pro 32 bit on a machine with no floppy drive.The mobo is Asus p5b and intel e6600 core 2 duo cpu.how can i get raid drivers on to machine without floppy drive.can i use usb pendrive? or can i install driver after i have installed Windows 7 pro?
View 3 Replies View RelatedInstalled a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
View 1 Replies View RelatedI need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies View RelatedI have set up a dual boot- Windows 7 pro & XP ultimate, both on separate SSD's, all OK. I also have two 3TB HDD's set up under windows 7 RAID, all OK. In XP under drive management the RAID drives show up twice, once as 775GB unused drives with no drive letter allocated and also as 2.7GB RAID drives with status 'failed', drives marked as 'missing'. Is there a way I can get the RAID drive accessible under XP?
View 8 Replies View RelatedMy SSD main drive is running low on space .My motherboard supports 2, SATA3 connections.My current drives are SATA2 SSD main drive and a SATA3 1TB media drive.If I were to add 2 SATA3 SSD's in RAID, does that use up both the SATA3 ports on the motherboard? or do they just combine and use 1?
View 1 Replies View RelatedI built a new computer.I wanted it to be more reliable. So, I got two identical hard drives. I installed Win 7 Pro as one big C: partition. Then I converted to dynamic disks and mirrored the first disk onto the second disk. Everything works! I even gave it a test. I powered off, and disconnected the SATA cable on the first hard disk. Windows booted right up, off the second HD. Great! It seems the mirroring works and can tolerate a missing disk.(I had to rebuild the mirror after doing this test.)I have some questions about how this will work over the long term. I noticed that when the first hard drive was missing from the mirror Windows never gave an error message. How would I detect a failing or failed hard drive? This is important, I think.How does Windows deal with a bad read on one hard drive in a two drive mirror? Say if one disk reads correctly, but the second disk reads a bad sector, how does Windows know what is the correct data?I found that Windows gives a text mode menu when I first boot up the computer. It wants me to select which Windows I will boot: the first hard drive or the second "Plex". Is there a way to set a default, so it will always boot the first instance of Windows without user intervention? Or would this defeat the mirroring function in the case of a bad hard drive?
View 3 Replies View RelatedI have 2 SSDs each partitioned into 80GB and 40GB like this:
-Drive1-80GB (boot) and Drive1-40GB
-Drive2-80GB and Drive2-40GB
Drive1-80GB is already the Windows 7-64 boot partition for the system. Can I configure a software RAID-0 with Drive1-40GB and Drive2-40GB? I know this is unorthodox but I wanted to try this for a few reasons.
I need to know how I can format a Raid Hard Drive to a Windows Format.
View 2 Replies View RelatedWe have two disks in raid 0. We want to get rid of them, as they are failing and install a single hard drive with Windows 7. We currently have Vista installed. There are no files I need to copy, just want to start with a fresh operating system. How do I go about this? Can I just remove the old hard drives and replace with the single hard drive and install Windows 7 on it, or is it more complicated than that?
View 8 Replies View RelatedI had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.
View 4 Replies View RelatedI'm working on a computer with a RAID setup. It is 2 hard drives 500gb each showing up as 1tb in windows. Both drives show up in the bios but all of a sudden when trying ot start the computer I get a "Operating system is missing" error.
I'm trying to run a chkdsk form a win 7 64 bit disk and telling it to run on H; (system drive) but it says 'cannot open volume for direct access'.
The other drive, C: is just a recovery drive built into dell computer systems. I tried using a boot cd and running mbrfix to no avail.
I've got 2x1TB partition using raid 0 on C: drive which I recently shrunk a little to make a 10GB partition to put "secure" items into. When I try to enable bitlocker encryption on the partition, it gets part of the way through and then my computer dies horribly. It's not a BSOD, the screen is black and windows tells me it can't find its loader.I reboot a few times and everything is back to normal.Delete the partition, re-create it, format it and try again, same thing.
View 3 Replies View Related