I had an existing properly working system consisting of a SSD 64GB for my OS and a Raid1 config with two 1TB drives for data. My SSD ended up being to small as certain programs do not let me remap content to a separate drive. I have upgraded (swapped out) to a 240GB SSD reinstalled windows on it and windows does not see my raid1 in disk management, nor does it see my two monitors or my connection to my router. It was my understanding I could just swap out the SSD's and reinstall windows and it would see everything.
I just purchased a new 10,000 RPM VelociRaptor drive and I'm going to use it as my OS drive. Is it possible to set up a RAID 0 with my current drive (hitachi 1TB 7200RPM) without having to format it?
Biggest bottleneck in my system right now is my boot drive, which is a WD velociraptor. I want to change this for dual 120GB SSD's in Raid 0 configuration. Can anyone walk me through the steps to copy over the existing Win7 64 install onto the SSD's, I dont want to have to load everything again
I just recently purchased a SSD (OCZ Vertex 3 60GB). I wanted to use it for Intel RST with my 500GB HDD. I went into BIOS and changed to RAID and i installed my OS. Everything was fine so I installed all the important drivers and reset. When it booted up again the RST sign came up and i accelerated my drive. Then when i reset my system it says "BOOTMGR is missing". So i poped in my windows recovery disk to try and fix it but the windows doesnt detect my drives.
MOBO: GIGABYTE Z68X-UD3H-B3 REV 1.3 SOmetimes when i switch to AHCI then it will boot
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
I have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
I have Win 7 Pro 64 bit installed on an ASUS P7P55D LE motherboard which supports RAID 0,1,5 and 10 using Intel Matrix Storage Technology through an on board Intel P55 chip set. The system was assembled in Nov 2009 using two Western Digital Caviar Black 750Gb drives in RAID 1 as Drive C:. (I now know from Western Digital Customer Service that I shouldnt have done that, but lets move on from there). Last December, an error message informed me the RAID array was broken and identified one of the 750 Mb drives as needing replacement. I happened to have a spare 1.5Tb WD Caviar Black at the time, so I pulled the 750Mb drive and replaced it with the 1.5Tb drive. Life was once again good. Then on July 4th (wouldnt you know) there was a repeat of the December 2011 error message telling me to replace the other original 750Gb drive. Okay so I had another 1.5Tb WD Caviar Black laying around (dont ask) and did a similar swap out. Thats when I emailed WD Customer Support asking about the 750 since their diagnostic software said the drives were fine. Thats when I learned that I should be paying lots more for enterprise quality drives if I want/need RAID. Well thats not what ASUS says in their advertising, but live and learn. All thats prologue, because my real question is whether its possible to break the hardware-based RAID 1 array and set up a Windows 7-based RAID 1 with the two 1.5Tb WD Caviar Black drives without having to reinstall Windows 7.
I had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.
Which configuration would be better using mobo sats 2 raid or using seperate rid controller via pcie card Rosewill Rc-211 wsis3132) or should I use mobo for raid and card for extra sata w/o raid I have more drives than sata slots. How do I transfer data videos/Tv shows from existing drive to raid?
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
I have a laptop that I bought from a highstreet shop that came with win 7 already installed. It didn't come with the disks or anything though. Now, I am probably going to buy another laptop and was wondering if there was anyway to move the OS over? I will be moving the HDDs across from one laptop to another, will I just be able to boot from the primary HDD that has the OS on it?
I had done a large number of System Restores recently, then a complete re-installation of Windows 7 via the Toshiba software partitioned in my laptop. I had updates waiting to be installed before that and I'm also worried whether the ones previously installed were picked up automatically. Now I'm not sure how to proceed.
I just did some reading and found out how important the updates are security-wise. Previously I had thought they they were more or less optional.
I've tried all the methods I can find, and I'm not so strong with boot files or images in general.
I have an image of my current system, created last night ( created in windows 7 from the "Ctrl Panel> Recovery>Create a system image" option) stored on my external 1.5Tb drive. It is stored in the "WindowsImageBackup" folder that was created and contains two .vhd files. one is obviously the image at 39Gb)
With my system running (Win7 Home Premium) I want to install this image onto a new, larger HDD and then replace my current drive ( 80Gb ) with the new, larger drive (320Gb ).
I simply want to copy the image from my external 1.5Tb drive to a "New" 320Gb drive (connected to my system via a USB2.0 to IDE and SATA cables that I use for backing up people's files and things from crashed machines) The "new" drive shows up in "Disk Manager" as "E", healthy partition, formatted, etc.
Is there a way to install my backed up image to my 320Gb external drive, THEN open my desktop pc, and replace my current 80 Gb drive with the 320Gb drive (already imaged and bootable as if nothing changed except the size of the drive) ? Also, do I need to delete the partitions on the "new" 320Gb drive so that it shows up as unallocated space?
I have a Gigabyte GA-P35-Ds3 motherboard that has just died. Do I need to replace it with the identical model or is there some leeway in replacing the mobo that won't affect the current Windows 7 licence.
I recently had hardware failure that resulted in myself RMA'ing my motherboard. It is my understanding that I will be receiving the same model of motherboard, but a different unit. Am I eligible to use my current Windows 7 product on my computer after I receive my replacement motherboard? Specifically I'm using Microsoft Windows 7 Home Premium 64-bit OEM.
For one reason or another I am frequently installing a fresh copy of Windows 7 onto my hard drive. I use a lot of software so as things get installed and uninstalled bad things tend to happen and sometimes things are beyond repair.My question is can I use my product key to download from someplace an image of Windows 7 with all the updates already installed? Installing the updates becomes very time consuming and the machine has to be restarted many times over so I am trying to avoid this. I suppose I could disable the updates but that is not really my intent at this time.
I have at the beginning have 1 (Fckyeahphotography ) account i logged in to the system. but later i got another one with my Blanket name i need type in my name sandra. The funniest is i cant see my 1st Sign in account Fckyeahphotography in system and no i cant sign in in my 1.st account.
Assume I have opened a couple of windows for some applications on my Win 7 desktop.Can I somehow store the current window positions and sizes (and restore them later (even after a reboot))?As far as I remember there is a tool which ofers this feature but I don't remember the name.
I have my current system live and working well. I want to add an SSD as the main boot drive.Is there a way I can migrate or reinstall easily on the new drive without having to run updates on everything again? The only hardware changing (adding) would be the SSD.I plan to format the old drive to use as storage.
So I have Windows 7 RC installed on my computer still, and as we all know.What I want to do is simple, I want to reformat my hard drive, and install Windows XP Pro...which I own and have a product key for.When I put my CD in the drive and restart, I get the "Press any key to boot from disc" screen, I press a key, and it'll take me to the blue Windows Setup screen, and it begings to inspect my hardware.. and this is where the problem is (I haven't even began to install or make any changes to my hard drive and I get this lovely blue screen of death-type error: A problem has been detected and windows has been shut down to prevent damage to your computer.If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:Check for viruses on your computer.Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated.Run CHKDSK /F to check for hard drive corruption, and then restart your computer.
Now, I haven't have any changes to any hardware on my laptop ever.I ran chkdsk and it didn't find any errors, and it ran both a quick scan, and full scan. And I also ran some type of scan within Window 7 (right-click drive C, then "Properties", then "Tools", then something like "Scan drive for errors/bad sectors") and it also said everything was fine.Last night I sat down, backed up all the necessary data from my hard drive, and was looking forward to having a clean installed OS, and I can't even get it to install.
I'm currently building a Server as well as in the market to snag a new laptop. How would I go about making my computer a virtual machine so that I could port over to my new gig.
Reason for this is that eventually I would love to get myself more "Organized" with where I keep important documents versus random crap. Stored all over my various machines.
My current Hdd which contains my OS and program data totals nearly 249GB, obviously SSD's which are this big are very, very expensive, how can I transfer my current OS install to a new SSD in an easy as possible way but keep the OS and the programs that are installed.Some of the stuff on there, like games, I guess I could uninstall and then reinstall them later so that they are no longer on the boot drive.
I took my computer in for some repairs and requested that I get Windows 7 installed on it since they wiped the hard drive for me to begin with. So they did that and never bothered to ask if I wanted 32bit, or 64bit.My motherboard and so on are 64bit compatible, and the sole reason why I want this is because many of my video-games claim that I don't have enough memory with the 3.25gb of RAM usage to use certain video settings. In reality I have 16gb of RAM ready to be used, unfortunately the 32bit Windows 7 can't use it. Kind of lame that in 2012 all versions can't simply do it, but I'm sure more technological reasons negate it.Now my questions are that my current 32bit Windows 7 serial key can be used with a different install CD that is 64bit? My sister has Windows 7 64bit CD and I'm wondering is that even legal to do to begin with, as well as possible? Oh and I'm aware they must be the same version such as Home Premium, which they are.
I'm trying to delete the windows.old folder, but found out that I have Securom and it's preventing me from doing so. There are two files that are apparently encrypted with strange names and I've found some advice on how to completely remove Securom from my computer. However, I just want to make sure that I don't remove it completely as I'm currently playing Company of Heroes: Game of the Year edition (Amazon download) and the Mass Effect 2 demo. how to remove the files in windows.old only? Does this involve deleting specific registry keys, too?
I bought this computer three months ago, and had no problems, up until now. It all started with it freezing up all of a sudden, forcing me to restart. But the display didn't show up. Tried again. Didn't work. Eventually, I removed my GPU and placed it back again, thinking it was loose. Then it finally worked.
Then it happened again. So after taking out my graphics card twice, it finally started working, but my HDD started making strange sounds. A sound I've never heard before, and only occurred during start up. I shrugged it off.
Now I start getting these sort of instances, when what ever program I have open, stops responding and Windows get's pretty laggy. The Windows Explorer (Not IE, the tool bar thing) also is unresponsive. I know it can't be a virus, Trend Micro showed no signs of anything after I scanned my computer a bunch of times.
So I did what any sane person would do, I did a bit of research on the net, and found this thread on this forums. The person here had a similar problem that I did. After reading most of the comments, I downloaded HDD SMART, as instructed, and apparently "Current Pending Sector Count" is yellow.
My windows is minimizing the programs that im using. Well not exactly minimizing but sort of putting it back to desktop. I tried to install the windows again but whit no results. it's doing it again. I cant even write my documents in word properly because of this.
Installing Windows 7 64 bit to new ssd. The current hdd will still have the current Windows 7 OS on it. As long as I have the bios boot set to the ssd can I leave the other win 7 OS on the mechanical drive in case of problems ?
