I created a backup and image (Win 7 Pro) on an external (USB attached) HDD and then created a Windows 7 System Repair Disk. I then booted from the repair disk and the attached external drive is not visible.
The external drive is attached via through a hub, does it need to be attached directly? Is their a generic USB Mass Storage Device driver that I can load?
I was hoping that by creating the repair disk that all necessary drivers would have been loaded to the disk, but apparently not.
I made a few months back a backup of my machine(windows 7 64bit edition). The size was like 25gb's so I saved it on my external hard-drive(I bought a case and put a hard drive(Seagate I think) in it). I know want to use this to restore my computer. So I made a system repair disk and loaded it up. However it cannot find my external hard-drive. I have "WindowsImageBackup " in my root directory of my external drive. Yet it still does not see it. I would install some drivers but I have no clue what drives I need as when I plug it into my computer and I am in windows 7 it finds my drive. What do I need to make window 7 recognize my image?
I am running Windows 7 RC on my Samsung NC10 netbook. I would like to create a system restore disk to allow me to restire system images, etc. However being a netbook the NC10 doesn't have a CD/DVD drive and while I can use an external one, it would be much easier to have the repair disk on a Flash Pen Drive.
Can anyone help me to create a repair disk on my pen drive?
Created it with no problems, apparently at least. My BIOS is set to boot from CD drive, so why won't my machine boot from the system repair disk? There were no errors when disk was created. My machine just boots to windows.
Anyone else experience this with Win 7 Professional?
I did a search in the Windows 7 forum for system repair disc and got no hits so here I am asking.I have only Windows 7 32-bit installed here so I don't have a 64-bit system with which to create a system repair disk. I do have a Windows 7 Ultimate setup disk. How can I make a Windows 7 64-bit repair disk?
I'm trying to created a posready 7 embedded image, and I want to be able to supply a system repair disc and system image with it, should the disk hardware fail for the end user.
The procedure seemed straightforward, and I'm running it straight after a fresh posready install to test it. I have 2 USB DVD drives attached, one to write the image to, and one because it needs the installation media as part of the creation process. from control panel, backup and restore, click Create a System Repair Disc Choose the dvd writer to use to create the disc and insert a blank disc, I choose E: in my case which has a blank DVD-R "Insert Windows Installation Disc", OK I put the Posready7 install DVD in the other DVD drive F: , click continue... System Repair Disc could not be created, The system could not find the path specified (0x8070003) I have tried inserting instead a Windows 7 Professional DVD at step 3, have tried with a single DVD writer, swapping discs, have tried on a couple of different posready7 installs, one with the 100MB system reserved partition and one without.
I've googled the error code and got lots of results suggesting corrupt user profiles etc, but these are new installs.
My laptop is 6 months old - sony vaio. Do I require to create System Repair Disc? I have taken back up in external hard drive. Also have created windows 7 backup in three separate DVDs.
I have never had the need t use this disk till now but as I am getting problems starting up I tried System Restore and it didn't work (I have tried 2 restore points).Can I use the repair disk that I created on my HP desktop to mend the system or to restore it to an earlier time ? When I open the repair disk on the computer it just shows a couple of folders (boot ,sources as well as a file called bootmgr but I can't see a hrep file to let me know what I can do...
getting a USB mouse or keyboard to work while using a Windows 7 system repair disk. My USB mouse seems to mostly be the problem. The keyboard works most of the time, so why doesn't the USB mouse work
I'm writing about my brother's Samsung R780 laptop (running Windows 7 64 bit), which recently stopped working. When he starts the computer, he gets the following error: "Windows Error Recovery." Searching around online led us to create a system repair disk on my laptop (which also runs Windows 7). When we boot with the disk in the drive, a prompt asking for our language (which is greyed out so we can't change it) and our keyboard (which we can change) appears. Without changing the keyboard option, we press 'next' and then it freezes. We've also tried the 'repair your computer' option in the Advanced Boot Options, but it also freezes.
I have a problem which I can't seem to fix. I have 2 laptops, both dvd drives are not working. I have an external Usb drive that won't work under boot up. Laptops don't recognise it until drivers are loaded.Hp pavilion dv6500 won't boot. Mbr is damaged. Can't use repair disk as won't recognize Usb drive.So I put hdd into my other laptops 2nd hdd port " Hp pavilion Dv9800 and repaired boot sector that way. Tested it on dv9800 and boots fine.Put hdd back into dv6500 and get same mbr fail message.
I bought a new laptop yesterday and today decided to create a system repair disk. I inserted a blank DVD RW and started the process the progress bar went to about 60-70% (estimate, does not give actual progress %) in half an hour and has now been at that exact same point for the last 5 hours. I have had no errors and the window still says "creating disk..." and it still sounds as though the DVD drive is still writing onto the dvd. I Wouldn't think it would take this long to create especially with no progress.
Here is a summary of my problem: 1) My computer recently got stuck on the "Starting Windows Screen." So I manually held the power button to reboot. 2) On reboot, it said there was a need to run a startup repair, which I did. Everything checked fine, except for the last one which said "System Volume on Disk is Corrupted," which it claimed to have successfully fixed. 3) After rebooting from repair, the system gets stuck on "Starting Windows Screen" for a good 10-15 minutes, after which it runs a registry check. After it completes that I get hopeful -- but the screen then gets stuck on an all black screen with just the mouse cursor and nothing more. 4) Additional note: Attempting to start the computer on "safe mode" leads safe mode startup to become stalled on "DRIVERSCLASSPNP.SYS" 5) The lastest attempt to repair yielded this message: "Startup repair cannot repair this computer automatically.
Problem event Name: Startup Repair Offline Problem signature 01: 6.1.7600.16385 02: 6.1.7600.16385 03: uknown 04: 21201099 05: AutoFailover 06: 2 07: Corrupt Volume OS Version: 6.1.7600.2.0.0.256.1 Locale Id: 1033
This isnt the first time i use the windows backup to create a system image, ive done it before using this external hdd with no problems at all.But now, for some reason it wont detect this hard drive, it only gives me the option to store the image on a dvd, i dont know why?, i tested the hard drive on a different computer and IT WORKS, i tried to create an image and it does work.
I've an all-in-one computer but would like to mirror the hard drive with an external usb drive, main hd 1T internal and 2T external partitioned into 2x1T one for mirror and other for data. Is this possable, running 7 Ultimate.
to create a recovery media on WD external HDD of Windows 7 from the recovery partition on my sony vaio VPCEH25EN laptop. i'm unable to do so from VAIO CARE since it only asks for an optical drive or USB flash drive, so it's not detecting it as a usb flash drive.
i have a Sony Vaio laptop with windows 7 home premium 32bits and i wanted to create a system repair disc with the windows 7 tools but this laptop has no CDDVD drive so obviously the tool gives an error asking for one to be pluged in...o the question is, is there any other way to create a system repair disc or do i need to get an external cddvd drive?EDIT: forgot to say, the point is so i can create an image of the system repair disc so i can put it on an USB drive
We had an external USB drive with tons of media files on it connected to computer A running Windows 7 Pro SP1. The drive was safely removed and connected to another computer that was running Windows XP Pro 2002 SP3. I was told that the drive was not recognized in XP and that it was disconnected (I cannot say for sure "Safely") and returned to the Windows 7 computer. Once the drive came up I get the following:
K: is not accessible. The disk structure is corrupted and unreadable.
I know every drive fails eventually and I'm not sure how old this drive is. Any utilities to use to try and repair the file structure. I have only tried rebooting the Windows 7 computer and that did not change anything.
I had an issue where Windows 7 would not boot anymore, getting error, BOOTMGR missing, Press Alt-Ctrl-Del to restart. I have tried to repair with windows disk but still getting error. I have decided that I want to just do a reinstall but I want to get on and export my favorites and grab a couple other things. I used to have a CD that I could use to boot up with (Think it was called Barts Boot Disk, Been too long) to get into Windows XP and do a couple things. My question is, is what is the best boot disk that will allow me to copy files from the HD to my external drive before I refresh?
I have an external HDD that works on any other machine I test it on, except mine. It was working and for some reason I recently needed to use it and it didn't work. It appears in device manager but not in disk management. A drive letter might not be assigned to it, I can't see it in disk management to assign a drive letter to it.
My laptop does not read my new external hard disk drive using USB connection. The sign "Safely remove hardware and eject media" is there. But the icon of the hard drive doesn't appear in the "Computer".
I have an Acer Iconia W500 that came preinstalled with Windows 7 32bit Home Premium. I made recovery discs from the tablet before installing Windows 8 on it, which runs great. What I would like to do, if possible, is to use those Windows 7 restore discs and restore them to an external hard drive and be able to boot from it and run the original Windows 7 that came preinstalled. The reason I am wanting to do this, as there were some programs, drivers, and other things that I cannot download from Acer or retrieve from the restore discs, and can only access from the OS if it is actually running.