Sata Devices Reporting As SCSI, Performance Issues

Aug 15, 2009

Just installed Windows 7 RTM and my Sata HDD's and DVDRW are reporting as SCSI devices. I would get this problem in XP if I installed the mobo's raid drivers by accident. If I did then the devices would report as SCSI and the dvd burner would report as a cdrom and would not burn or read dvds

Whereas in Windows 7 the burner is reporting as a DVDRW scsi CDrom and will play dvd's and burn them too.

So at the moment there doesn't seem to be any problem however whilst navigating through the control panel I noticed the WEI. So I took a look and it's report my primary hard drive with a score of 5.9. The hard drive is a brand new Western Digital Caviar Black 500gb 32mb cache disk, is this score normal for such a drive?

Also is there anything else to worry about with the devices reporting as SCSI or is okay to leave it like that.

View 3 Replies


ADVERTISEMENT

SATA SSD Drive Shows Up As SCSI

Jul 22, 2010

I have a Dell XPS730 with the Nvidia Nforce 790i chipset. I run two 500 gig SATA drives under RAID 0. I recently installed an Intel X25 80 gig SSD and have ran into problems. Windows recognizes the drive as SCSI in device manager. Granted it works however because it is listed as SCSI TRIM and the intel toolbox wont work which makes an SSD useless.After tons of research I have found that because of the Nvidia chipset it makes the drive show up as SCSI. I have tried Vista and Windows 7, both show it as SCSI. I have moved the SATA cable away from the other main 4 that support RAID with no luck. I have refomatted several times as well with no luck. I have completely disabled RAID in the bios and it STILL shows as SCSI. Is there any way to get around this? I have read that changing the nvidia controller drivers may work but im not sure what I would switch them to?

View 9 Replies View Related

SATA Drives Showing Up As SCSI Windows 7 Ultimate?

Jan 17, 2012

I've been reading about issues with people having problems with their SSD's not being reconized by Windows 7 Ultimate.but my WD 600gig STAT III Raptor is listed as a SCSI as well. I assume the problem is with my Marvell Driver.I bought this 60gig OCZ Vertex 3 SATA III drive for a Boot drive and had a pain installing drivers for it on a clean install of windows. I plugged it, and my WD Raptor both into the 2 SATA III ports that I have on my ASUS Rampage III MB. I set the Drives to ACHI not IDE. Tried to install Windows, had to force windows to accept the Marvell Drivers...but finally got it installed.Now Im stuck with the OCZ SSD and the Raptor both at SCSI speeds...not able to get them reconized my Windows 7 Ult as SATA drives.Should I try uninstalling the Marvell and JBMicron drivers and let Windows try and install drivers that will work? Funny thing is, I know that windows is reconizing the SSD as a SSD because of the Disk Defrag has been disabled on it...and was able to get some info off the drive via Intels SSD toolbox....OCZ's tool box wont reconize it unless you use Windows drivers. I had to install the Marvell Drivers to install Windows, Windows wouldn't reconize either drive plugged into the SATA III ports.I've tried bout everything, even tried the reg. fix via the Windows Helper with no luck.

View 1 Replies View Related

Replacing SCSI Storage Drivers With IDE Or SATA Drivers?

May 18, 2012

Having issues with RAID0 array being detected by Windows7 Ultimate x64 as SCSI. Apparently these drivers are the 'default' drivers that install when the RAID array is initialized. There is no option at this point to install other drivers instead.Using DeviceManager, there is an option to 'update drivers', and regardless of the method chosen, even selecting the file for a previously-downloaded set of drivers, Windows7 always comes back with a message of "Windows has determined that the best drivers for your system are already installed". Considering that SCSI drivers are the OLDEST ones out there, and actual SCSI devices are becoming rarer and rarer, how is it that these drivers cannot be replaced with more current and more applicable drivers?

View 5 Replies View Related

Cannot Boot From Devices On RC-209-EX (SiL3114) PCI-SATA Adapter

Jun 12, 2012

When I installed a TF III GTX 570 video card I lost my PCIE-X1 slot and 1 SATA port on the Inspiron 530 Foxconn G33-M03 MOBO I am still running. Now aside from the fact that I need to upgrade the MOBO...

I added a Rosewill RC-209-EX PCI-SATA adapter (SiL3114) to gain back 4 SATA ports. The card is working fine. It is slow compared to the MOBO SATA ports but I expected that. I have a Seagate 500GB HDD and an Optiarc DVD R/W drive attached to it. BUT..... I can not boot from either device. They do not appear in the boot options....

Based on my reading I got the "NON-RAID" (IDE/ATA emulation) BIOS from Silicon Image and flashed the card's BIOS since I will not be using it for RAID. It is just for more SATA ports. Should I be able to "see" the PCI-SATA card and its attached devices in the 530's BIOS Setup Screen? Is it a limitation of my Dell neutered BIOS?

The RC-209-EX documentation specifically states it "supports" CD/DVD drives.

There is plenty written about booting from a RAID array configured to the RC-209-EX but very little about booting from single device.

View 3 Replies View Related

PSU Died, New PSU, Bios Won't Recognize SATA Devices, Now Won't Turn On

Oct 18, 2012

Synopsis: PSU died, replaced PSU with different model, system boots to bios successfully but does not recognize any devices in SATA ports, nor do those devices appear to be getting power. Now can't even get to BIOS, entire PC flicks on and off repeatedly as soon as I turn the PSU on regardless of whether I hit the power button on the front of the computer.

System Specifications

Original PSU that died: SeaSonic M12II 750 SS-750AM 750w PSU
CPU: Intel Core i5-3570K Ivy Bridge 3.4GHz
GPUs: ASUS 670 non-top version, SLI (2x)
MOBO: ASRock Z77 extreme 6
RAM: Mushkin Enhanced Blackline 8GB (2 x 4GB) SDRAM DDR3 2133
Optical drive: Sony AD-7280S-0B 24x SATA Internal DVD+/-RW Drive
SSD: SanDisk Extreme 240GB SATA 6.0 Gb-s 2.5-Inch (OS is installed here)
Storage drive: Western Digital Caviar Black 1 TB SATA III (This was not connected when power supply died)

Detailed explanation:About a week ago my PSU (Seasonic 750w) died randomly while the computer was left running in sleep . I RMA'd the dead seasonic. In the mean time I happened to come accross an extremely good deal on a new PSU, so I bought it (Thermaltake smart m850w PSU) to have a backup and to get my machine working again. I hooked up the new PSU to GPUs, CPU, fans, ATX power connector, and to all of the SATA devices, (the SSD, the HDD, and the Optical drive). I made sure to connect the data cables to the SATA devices in the same configuration they were in when working properly. The computer boots successfully to the ASROCK BIOS, all fans spinning. However, I get the error code "A6" on "dr debug" (the led display on the mobo). The manual says this means "SCSI detect". I have no idea what that means.

I was able to load the UEFI, and bios recognized all components except for any of the SATA devices--(SSD, the HDD, and optical drive not recognized). The RAM, GPUs, processor, and fans were detected. At this point I was stuck in BIOS because I couldn't boot off anything.I did not have the HDD connected when the PSU failed, but now the BIOS won't read that either. I don't think any of the SATA devices are actually receiving power. Again, the UEFI showed that there were no SATA devices connected to any port, when in reality they clearly were connected both by power and data cable. Then things get really strange. I unhooked all of the SATA devices except the HDD (the one that wasn't hooked up when the original PSU died). I plug the AC into the PSU, then turn on PSU (not the power switch for the computer, the switch on the PSU). The computer starts flicking on and off in this weird rhythmic pulsating pattern "click...click...click...click..." with about a 1/2 second between each click. Each time the power flicks on, the LEDs come on and the fans spin briefly. The strangest part is that I don't need to hit the power button on the front of the case for this to happen, it just starts as soon as the PSU is turned on. In fact, I can't get the computer to turn on at all--the switch on the front of the computer appears to be dead.

1. Unplug the power cables from everything and re-seated them.

2. Reseated the data cables to the optical drive and the SSD on the drive end, not on the MOBO side as they are covered by my GPUs and I would have to take them out in order to do that.

3. Tried hooking up a SATA power cable from my old modular PSU and using that in the new PSU in an attempt to power the optical drive (didn't work, I know, bad idea--I learned you aren't supposed to do this shortly after I tried it)

4. Setting all preferences to default in the UEFI.

5. Disconnecting the power cables from one or both of the GPUs.

I think that this is either a problem with (1) the motherboard, (2) the new PSU, (3) all 3 SATA devices (unlikely). The fact that I can't even get into Bios anymore tells me that this may be a MOBO or PSU issue.My main question is how to procede from here? I suppose I can wait for my Seasonic to come back from RMA--perhaps that will clear up the issue. I just can't shake the feeling that this is a MOBO issue though. I am worried that if I keep screwing around with it I may end up frying my CPU and GPUs. I can eat the cost of a MOBO or PSU if necessary, but I can't afford to buy a new processor and two new 670s.

View 9 Replies View Related

Changed The SATA Controller From AHCI To Raid SATA Result = FAILED?

Aug 10, 2010

Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:

At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED

On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.

View 9 Replies View Related

SATA 3 Not Working On Asus P6X58D-E Motherboard With SATA III Support?

Jun 27, 2012

Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?

View 9 Replies View Related

Install Sata Hard Drive As A Slave Where The Master Is Also A Sata?

Aug 10, 2011

i want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7

View 4 Replies View Related

Using X64, SCSI Driver Only Supports X86

Jan 15, 2009

I am trying to install drivers for an Adaptec AHA-2940 SCSI card.

The adaptec website there is no 64 bit version available, but i have been reading around for solutions with no success.

I need the "Adaptec AIC-7870 PCI SCSI Controller" ... but there is no 64 bit version for that. When i try to install the drivers (there is no installer program, i just need to use the update drivers feature of windows) it says that it is not a 64 bit version so i can't use it.

Is there any solution to my problem?

View 4 Replies View Related

SCSI Adapters Not Supported

Nov 6, 2009

Prior to purchasing a Vista Ultimate to Windows 7 Ultimate upgrade for $220, I downloaded and ran the compatibility/upgrade adviser program and found no problems.While running the Windows 7 Install disk, the installation stopped dead with the message that I must update the driver for my Adaptec 29160N SCSI hard disk storage controller. However it could not find a newer driver than the one I am currently using under Vista, version 6.5.645.100, dated 1/31/2007.

View 4 Replies View Related

Use Old SCSI Scanners In Win XP Mode?

Nov 5, 2009

I have a couple of old SCSI slide scanners and SCSI cards I use in (real) 32-bit XP, that no 64 bit drivers exist for. So I haven't been able to get them to work in Windows 7.

Is there any hope of getting them to work via Windows XP Mode in Windows 7? My impression scanning posts here is that this won't work, as I need real XP to talk to real SCSI cards with real drivers, and the virtual/emulated environment won't acommodate this.

I picked up a VT capable processor, hoping to try all this out, but now I find my Windows 7 RC eval setup can't load the RTM Windows XP Mode and Virtual PC software, so I'm unable to test it out. No way I'm springing for Windows 7 Pro only to find out the virtualization capability won't do what I need it to do.

Will I have to continue to dual-boot into XP when I want to work with the old hardware? If so, I'll just get the Windows 7 Home family pack, and forget about VT..

View 3 Replies View Related

Cannot Establish If Have An SCSI Driver Windows 7 SP1 32 Bit?

Dec 25, 2012

Having gone through all the setting up processes, my system will not produce Minidump Files, an SCSI miniport is mentioned as part of the production process, yet I have searched my system and cannot find one.

View 2 Replies View Related

[SCSI] Initio-940 (IOI-4203U) Driver

Sep 13, 2009

Anyone have working driver for this scsi card, i like this, and this can working good for my Umax 1220s flatbed scanner

View 0 Replies View Related

SATA-II Drive On SATA Raid Controller?

May 7, 2011

i purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?

View 5 Replies View Related

How To Load Windows 7 On Scsi Raid Systems

May 30, 2010

How to load Windows 7 on scsi raid systems? the drives aint recognise i had to load sata drivers for my portege laptop m400 what drivers do i need? raid or scsi from dell? poweredge 1800/2800

View 6 Replies View Related

LSI Logic 22910, 21002 PCI SCSI Adapter

May 15, 2009

I am trying to install Windows 7 on my test machine. However, I can't get it to detect any drives - three are 3 disks in the system - it is an IDE disk. When I try and install, it can't detect any disks, but when I try and install through Windows Vista, it detects them.

However, then it says it needs the driver for the LSI Logic 22910, 21002 PCI SCSI adapter; 53C896 Device. Is there still a version of this, and if so, where can I get it? I have tried everywhere I can think of, including the LSI website!

View 6 Replies View Related

Windows 7 Install To A SCSI Drive Without The Driver Installation (F6)?

Aug 28, 2012

Can W/7 install to a SCSI drive without the driver installation (F6)? I'm just about to install W7, and it seems to detect all 3 SCSI drives without the driver for the LSI 1030 Ultra SCSI adapter.

I'm just a little surprised how simple this is, usually you have to supply the additional driver...

View 2 Replies View Related

Lsi Megaraid 1600 Elite Scsi Card Drivers

Apr 19, 2009

I have a lsi megaraid 1600 elite scsi card which is not being dected by windows 7 64bit. I have tried several drivers packages for server 2003 and 2008 but it doesnt work. Lsi does not list visa drivers for this card on thier site. Does anyone have any suggestions.

View 6 Replies View Related

How To Uninstall A Gigabyte Scsi Raid Controller Which Was Installed

Dec 18, 2012

How can I uninstall a Gigabyte raid contoller without crashing my Win 7 OS? Uninstall is being prevented because "the OS is on the contoller"! Win 7 64 bit is on a Crucial SSD boot drive and AHCI is set in BIOS. However the raid controller is setting all internal drives to SCSI!

View 1 Replies View Related

X64 Windows 7 Is Reporting Only 3GB Out Of 4GB RAM?

Mar 10, 2010

I'm a bit confused why it's saying this. All the RAM is PC6400 and it's compatible with my machine.I see this when I go to System properties (right-click Computer and properties). Beside the Installed Memory (RAM) label, it says 4.00 GB (3.00 GB usable).

View 9 Replies View Related

CD-ROM Drive Is Reporting 52

Mar 4, 2010

it will not work it says that there is a problem to this effect "This device will not be available until the issue is resolved".

View 1 Replies View Related

Can't Connect Wifi Devices To Wired Devices?

Jun 25, 2011

I have been unable to connect to anything on my wired network, for about the last week. I don't remember making any changes however, I just became unable to connect.I having done a little troubleshooting.1. I can connect to the shares of my Windows Home Server if I use the IP address. The name does not resolve.2. Flushed DNS and restarting DNS server. Flushing DNS works on one client, to allow browsing by the name & restarting DNS works on the other. However neither works after a restart.3. Only my Wifi clients are experiencing this issue. My wired clients, desktops, PS3, Xbox 360, and Boxee can connect perfectly.This issue is not limited to my server. I can't connect to shares on my desktop, nor print to my wired printer.Some network background:I have DSL through CenturyLink and have a Linksys E2000 router.

View 2 Replies View Related

Error Reporting Feature

Oct 23, 2009

I recall reading some time ago about a new feature in Windows 7 for user generated error reporting that would allow a user to record their desktop / take periodic screenshots while they replicated an error, which would then allow them to forward / email the report to someone who could offer help.

I can't seem to locate this feature in Windows 7 Ultimate, and i'm having trouble locating any articles talking about the feature.

Was it removed or am i not looking hard enough?

View 3 Replies View Related

Reporting Win7 UX To Microsoft

Feb 2, 2009

I'm posting this using WinXP (my usual OS), and Windows 7 runs on the same hardware except it's a separate boot disk (ie, not a dual boot system).

I know I can click a link on the Windows 7 desktop to report problems etc, but how can I do the same from a machine not running Windows 7? Is there a URL that can be made sticky on this forum, perhaps?

In particular I want to direct them here - a solution (albeit trivial).

View 1 Replies View Related

Reporting Network Activity

Oct 30, 2009

So, 7 is reporting 4.5tb of network activity in 11 hours, with 600 gigs sent. I'm connected to my mac file server with roughly 1.8 TB of external hard drives (not NTFS either. mac formatted). It just keeps pumping out 5 megabytes a second and i have no idea where it's going. It doesn't show up in my resource manager, either, Any ideas?

View 4 Replies View Related

AVG Not Reporting Correctly In 7100

Apr 26, 2009

I have a yellow bar on the action center indicating that AVG is no longer reporting to Windows in a format that is accepted...

anyone else see this?

View 6 Replies View Related

Windows Is Reporting It Isn't Genuine

Jan 17, 2013

I am having some problems with Windows 7 Ultimate 64 bit that match exactly with this thread - Windows is reporting it isn't genuine, Validation code 0x8004FE21, Here are the exact results from the commands that you told us to enter.

View 2 Replies View Related

HDD SATA 3 (6.0Gb/s) Works With SATA 2 (3.0Gb/s) Controller?

May 22, 2011

My MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?

View 5 Replies View Related

Asus P6X58D-E - SATA II SSD Or SATA III SSD?

Mar 5, 2012

i'm looking to upgrade from a HDD to SSD. I've been reading online about my board and apparently the marvell 9128 controller sucks speed wise. I was looking at the Corsair Force 3 because of the read/write speeds. Upon doing more digging though it looks like id be better off running a drive on the SATA 2 ports.

View 2 Replies View Related

Disabling Error Reporting In Windows 7?

Jan 25, 2013

I would like to know if I disable the "Error Reporting" program is this also the "Event Viewer" program ? or are these two separate programs ? I just do not feel comfortable having my personal home computer telling (mother Microsoft) any of my personal "Error Reporting" problems However I still want to be able to know when and why my computer rebooted in the middle of the night at the same time for no apparent reason.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved