SATA Drives Showing Up As SCSI Windows 7 Ultimate?

Jan 17, 2012

I've been reading about issues with people having problems with their SSD's not being reconized by Windows 7 Ultimate.but my WD 600gig STAT III Raptor is listed as a SCSI as well. I assume the problem is with my Marvell Driver.I bought this 60gig OCZ Vertex 3 SATA III drive for a Boot drive and had a pain installing drivers for it on a clean install of windows. I plugged it, and my WD Raptor both into the 2 SATA III ports that I have on my ASUS Rampage III MB. I set the Drives to ACHI not IDE. Tried to install Windows, had to force windows to accept the Marvell Drivers...but finally got it installed.Now Im stuck with the OCZ SSD and the Raptor both at SCSI speeds...not able to get them reconized my Windows 7 Ult as SATA drives.Should I try uninstalling the Marvell and JBMicron drivers and let Windows try and install drivers that will work? Funny thing is, I know that windows is reconizing the SSD as a SSD because of the Disk Defrag has been disabled on it...and was able to get some info off the drive via Intels SSD toolbox....OCZ's tool box wont reconize it unless you use Windows drivers. I had to install the Marvell Drivers to install Windows, Windows wouldn't reconize either drive plugged into the SATA III ports.I've tried bout everything, even tried the reg. fix via the Windows Helper with no luck.

View 1 Replies


ADVERTISEMENT

SATA SSD Drive Shows Up As SCSI

Jul 22, 2010

I have a Dell XPS730 with the Nvidia Nforce 790i chipset. I run two 500 gig SATA drives under RAID 0. I recently installed an Intel X25 80 gig SSD and have ran into problems. Windows recognizes the drive as SCSI in device manager. Granted it works however because it is listed as SCSI TRIM and the intel toolbox wont work which makes an SSD useless.After tons of research I have found that because of the Nvidia chipset it makes the drive show up as SCSI. I have tried Vista and Windows 7, both show it as SCSI. I have moved the SATA cable away from the other main 4 that support RAID with no luck. I have refomatted several times as well with no luck. I have completely disabled RAID in the bios and it STILL shows as SCSI. Is there any way to get around this? I have read that changing the nvidia controller drivers may work but im not sure what I would switch them to?

View 9 Replies View Related

Sata Devices Reporting As SCSI, Performance Issues

Aug 15, 2009

Just installed Windows 7 RTM and my Sata HDD's and DVDRW are reporting as SCSI devices. I would get this problem in XP if I installed the mobo's raid drivers by accident. If I did then the devices would report as SCSI and the dvd burner would report as a cdrom and would not burn or read dvds

Whereas in Windows 7 the burner is reporting as a DVDRW scsi CDrom and will play dvd's and burn them too.

So at the moment there doesn't seem to be any problem however whilst navigating through the control panel I noticed the WEI. So I took a look and it's report my primary hard drive with a score of 5.9. The hard drive is a brand new Western Digital Caviar Black 500gb 32mb cache disk, is this score normal for such a drive?

Also is there anything else to worry about with the devices reporting as SCSI or is okay to leave it like that.

View 3 Replies View Related

Replacing SCSI Storage Drivers With IDE Or SATA Drivers?

May 18, 2012

Having issues with RAID0 array being detected by Windows7 Ultimate x64 as SCSI. Apparently these drivers are the 'default' drivers that install when the RAID array is initialized. There is no option at this point to install other drivers instead.Using DeviceManager, there is an option to 'update drivers', and regardless of the method chosen, even selecting the file for a previously-downloaded set of drivers, Windows7 always comes back with a message of "Windows has determined that the best drivers for your system are already installed". Considering that SCSI drivers are the OLDEST ones out there, and actual SCSI devices are becoming rarer and rarer, how is it that these drivers cannot be replaced with more current and more applicable drivers?

View 5 Replies View Related

Internal Drives Showing Up As External Drives?

Jul 21, 2011

I just finished putting together my computer, installed Windows 7 Pro 64 bits. However, both of my hard drives (one SSD, one regular HDD) are showing up as external drives (plug-and-play). If I click the "Safely Remove Hardware" icon, I could actually "eject" both of my hard drives.

View 5 Replies View Related

How To Get SATA Drives To Work ?

Dec 1, 2009

as some of you may know ive had a buggerload of problems with my LaCie external HDD, which, slowly, was put down to a faulty drive controller. Having taken out the HDDs held within, ( 2 samsung 500GB HDDs )

ive attempted to get 1 of them working as an internal drive. Ive connected it to the power and sata cable, but when i boot i (perhaps obviously?) am not getting any connection whatsoever. is there something i need to do in bios or something to get it to work? what am i doing wrong? (because invariably i AM doing something wrong).

View 9 Replies View Related

External Usb 2.0 Sata Not Recognised - Windows 7 Ultimate?

Nov 24, 2011

My sata usb 2.0 external drive is not being recognised in windows 7 ultimate 32bit.all my other usb devices work fine when plugged in.

View 2 Replies View Related

USB.E-SATA External Hard Drives

May 6, 2011

I am currently running Ubuntu 11.04 on my HP (DV5 1110em) laptop from an external USB 2 Buffalo ministation hard drive, I have noticed my machine is equipped with an E-SATA port. Would using an e-sata external hard drive be any faster that the usb option ?.

View 3 Replies View Related

Bios Not Detecting Any Sata Drives?

Aug 7, 2012

My pc had suddenly decided to not recognising any of my Sata drives. Win 7 32 bit, 4 gig ram, asus psn d motherboard,ati sapphire 1g pci card, 1 250g western digital Sata drive 1 x 1tb seagate hdd. Sata DVD drive

Yesterday my pc froze up while surfing the web, so reset it and that where the problems started

It only recognised one of the hdd then wouldn't boot got a bsod uncountable boot volume. So opened up the case to check if the cables where loose, nope, so decided to run a repair via the recovery console. Didnt detect my o/s at all ask me to install the correct drivers grrrrr. So stripped the pc down swapped the Sata cables to see if that was the problem, no joy at all would only find one Sata drive and DVD drive. Then it wouldnt recognise any of them, so swapped out the Sata DVD drive for an IDE drive. The booted up nothing bar the DVD drive. Have now come to a cross roads don't know what else's to try. Managed to boot via a USB drive with Linux and everything system wise, pcu, gpu etc works, but still no Sata drives.

Done some digging online and some ideas are not a big enough psu, faulty Sata cables, but swapped in an IDE hdd and nothing again.

View 8 Replies View Related

IDE Or AHCI For SATA Drives (SSD And Regular)

Sep 15, 2009

I would like the good and bad about running your SATA drives in IDE and AHCI modes.

I have 3 drives. 1 SSD and 2 normal hard drives.

Does it even make a difference? I have an Esata bracket that I want to run in AHCI mode but how about the normal system and data drives? What is the best way to set up drives?

View 0 Replies View Related

Blu-ray SATA Drive Not Showing Up In Explorer

Aug 30, 2011

Bought a LG Blu-ray internal sata rewriter. Installed it and windows 7 found it first time. So far so good. Put windows into sleep mode and when I woke it up the sata drive was missing. The drive was not only missing, but the tray failed to manually open and the activity light did not illuminate. Drive totally dead. Check all power and sata cables all ok. Done a full reboot and drive came back ok. This only happens when the machine is put into sleep mode. Sata drivers all up to date and all cables 100%. Turn the machine fully off or restart and everything works ok each time. Use sleep mode and it fails when you bring the m/c to life.

View 9 Replies View Related

Coming From XP, Enable AHCI For SATA Drives?

May 11, 2011

I'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.

My questions are:

1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?

2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)

3. I intend to run XP mode, will AHCI mode pose any problems for this?

View 2 Replies View Related

Installation Won't Detect PCI Adapter For IDE And SATA Drives

Apr 12, 2012

Just built a moderate spec gaming PC from scratch, and all has went according to plan except when I try to install Windows 7, my hard drive won't show up. My new motherboard doesn't have any IDE slots, but I only have an IDE hard drive. I am using a 'Pluscom Serial ATA PCI Adapter' to connect my hard drive to the computer as it has 1 IDE slot on it. I don't have a disc for drivers and don't know where to start. I am running Ubuntu on it at the moment so I can download any drivers I may need.

View 9 Replies View Related

Windows 7 Drives Letters Not Showing

Mar 28, 2011

I have Windows 2008 R2 servers as my DCs. I create a group policy on the 2008 servers to map my network drives. In Windows XP it works great 100% of the time. In Windows 7 this is not the case. I can't see the drive letters in My Computer but if I go out to DOS and look using the net use command I can see the drive letters 100 % of the time.I can also see the drive letters within programs.I just can't see them within My Computer.I looked at the Reg setting for the following settings and they are not in play.

View 2 Replies View Related

AHCI Mode No Boot From Sata Optical Drives?

Apr 30, 2011

A strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.

View 9 Replies View Related

Replacing Sata Laptop Hard Drives From Vista To 7

Feb 9, 2010

I want to put my old hard drive that has files and was used with windows vista and put it into a new windows 7 laptop. Is there any overlap or any config problems I can run into doing this? Or do I just put it in and the old files should work and all i have to do is update some drivers from vista to 7?

View 2 Replies View Related

Updated SATA Controller And 3 Disk Drives Disappear?

Oct 23, 2012

I updated the SATA AHCI controller from device manager and rebooted. Shortly after I noticed disk drives F:, Z:, and X: are gone. No big deal I'll just repartition right? No they aren't showing up in Disk Management? The driver I installed I got from gigabyte it was a preinstall driver for ahci. I just installed windows 7 64 yesterday to a Samsung 830 256gb and it was working fine maybe I shouldn't have messed with it. C: drive is working fine just the other 3. Should I roll the driver back? System restore? Did I install the wrong driver?

View 3 Replies View Related

Constant Freezing + Disk Read Error + Detecting SATA Drives?

Nov 1, 2012

So recently my desktop PC has been freezing at random times, and then sometimes restarting after not responding for a couple of minutes (no BSOD, just restarts as far as I've seen). It sometime freezes as soon as I turn the computer on, while Windows is loading, and sometimes it will start freezing after an hour it's been on. Most of the time it will just freeze for around a minute, and then unfreeze, but sometimes it does freeze and then restart. By freeze I mean everything, mouse included, and ctrl+alt+delete doesn't work.Also at bootup sometimes, it will fail to detect my SATA hard-drive and hang at Detecting SATA drives at the bios screen. This will be following by a disk read error.This problem started occuring a couple of weeks a go, so I reinstalled Windows 7 and it worked fine after that.

Running Windows 7
Bios: Phoenix - AwardBios v6.00PG
Processor: Intel Core2 Duo CPU E6550 @2.33GHz
2GB RAM
Graphics Card: Nvidia GeForce 8600 GS

View 5 Replies View Related

Windows 7 Ultimate SP1 - Cannot Create Map Drives

Oct 3, 2011

I am trying to map to a network drive and I cannot, this is am hp laptop running Win 7 32bit ultimate, if I map to \servernamesharename, cannot map, I cannot even browse to select the servername, I can ping the two servers I have, I also have the local account in the laptop in the two servers which are still win nt 4.0 servers that only acts as storage servers, but if map using \serverIPSharename, then I can map to it. Is there any security settings that I need to change? I have others computers running win 7 6bit proff, and never had any issues like this.

View 5 Replies View Related

Windows 7 Ultimate Showing Different Version?

Jul 31, 2012

I have downloaded windows 7 ultimate x64 iso file. X17-59465.iso but after installed, it is showing windows professional which is weird.

View 4 Replies View Related

Explorer Not Showing Drives

Apr 9, 2009

Can someone help me how to solve this problem?

F drive (label: Multimedia) and G drive (label: Download) doesn't show in Windows 7 explorer

And here's the Disk Management window

Anyone can help me with this?

I'm running on Windows7 Build 6801 32bit

View 6 Replies View Related

Files Showing On Network Drives?

Dec 17, 2012

My problem is with all the users files on the file server don't all show-up. Some stay as 'My Documents'.

I believe there is something to delete within the folders to make it show the names properly, but I can't remember.

View 1 Replies View Related

1 Of 3 Mapped Network Drives Not Showing Up?

Sep 26, 2011

Windows Server 2008 R2Windows 7 32 BitI have a Windows 7 Enterprise box that when started will only create 2 of 3 mapped network drives. This does not happen every time either, just about 2-3 days of the 5 day work week. 2 of the drives are mapped via a script, while the 1 drive that is the problem child is set through the Properties-->Profile-->Home Folder of the user on our AD box. We have set the drop down letter to H and verified the path. It is correct, as it works some days.

View 8 Replies View Related

Laptop Is Not Showing Access To Pen-drives?

Jul 21, 2012

my lptop iws not showing access to any pendrive.

View 1 Replies View Related

OS Install And No Hard Drives Showing Up?

Dec 9, 2012

I'm installing Windows 7 on an older PC. It was running on it before but my hard drive bit the dust. When I boot from the install disk and go to install it, there are no hard drives listed and the message says "No drives were found. Click Load Driver to provide a mass storage driver for installation."

It's an old Dell Dimension 8300 with a couple WD hard drives in it, a 250GB and a 500GB. I could get the model numbers if that's necessary.

View 6 Replies View Related

Service Pack 1 (Windows 7 Ultimate 64bit) Not Showing Up?

Jan 7, 2012

Microsoft's online support for downloading service pack 1 seems to end at "Use Windows Update" However, my Windows Update just can;t seem to find it. Is there any way to manually download it or get Update to find it?

View 1 Replies View Related

Memory Card Reader Not Showing Drives?

Oct 10, 2012

I have a Dell XPS M1710 laptop. I recently installed windows 7 home premium 64bit. I can't seem to get my built in Ricoh 5 in 1 memory card reader to work. I installed the recommended driver using the dell drivers on their website. None of the drives are appearing under my computer, and nothing happens when I insert a memory card. I have tried several 1 and 2gb cards. Both high speed and regular with no success. I went to folder options and unchecked the box to hide empty drives in my computer. I am unable to locate anything under device manager for the Ricoh card reader.A - I want it to display the empty drives in my computer
B - I want it to read my darn memory cards

View 9 Replies View Related

Windows 7 X64 Ultimate Stopped Showing Video Clips Thumnails

May 14, 2010

I don't know what happend but my Windows 7 x64 Ultimate stopped showing video clips thumnails. Picture thumbnails do work.

View 9 Replies View Related

Gaming Graphics Drives For Windows 7 Ultimate 32bit On Hp Pavilion G Series?

Jan 28, 2013

i'm using hp pavilion g series intel inside core i5,originally it was installed with windows 7 home premium and after i experienced some problems i upgrated to windows 7 ultimate.so now i wanna load gaming graphics on my laptop and i'm struggling.

View 2 Replies View Related

Gaming Graphics Drives For Windows 7 Ultimate 32 Bit On Hp Pavilion G Series Intel Core I5

Jan 28, 2013

i'm using hp pavilion g series intel inside core i5,originally it was installed with windows 7 home premium and after i experienced some problems i upgrated to windows 7 ultimate.so now i wanna load gaming graphics on my laptop

View 1 Replies View Related

Pci Sata 6 Raid Card That Has At Least 4 Slots For 4 X 2tb Hard Drives For A Raid 5?

Aug 24, 2012

I need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved