I want to put my old hard drive that has files and was used with windows vista and put it into a new windows 7 laptop. Is there any overlap or any config problems I can run into doing this? Or do I just put it in and the old files should work and all i have to do is update some drivers from vista to 7?
View 2 RepliesI am currently running Ubuntu 11.04 on my HP (DV5 1110em) laptop from an external USB 2 Buffalo ministation hard drive, I have noticed my machine is equipped with an E-SATA port. Would using an e-sata external hard drive be any faster that the usb option ?.
View 3 Replies View RelatedI picked up a used computer that has vista. I have an extra hard drive with windows 7 on it. Is there something I need to do other than swapping out the hard drives? Replacing the vista hard drive with the windows 7 hard drive. When I did this, the pc will automatically run system repair. I get patch prevented the system from starting Windows 7 will not start on the pc, so is there something else I must do?
View 1 Replies View RelatedI have vista installed on a seperate 500gb hard drive. I keep all my media stored on 4tb of other harddrives separately. they are setup as dynamic disks spanned together. Once I upgrade will those drives still work properly and will I loose any data?
View 1 Replies View RelatedI need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies View RelatedI have a Dell Inspiron 1545 laptop. I recently developed hard drive trouble and have had to order a replacement.Instead of installing Windows 7 all over again, with all the drivers, etc., I want to clone my existing hard drive to the new one.I intend to connect one of the hard drives to my system via a USB SATA cable with the other drive connected inside my system.
View 2 Replies View RelatedI have a brand new Toshiba laptop with Vista. It arrived just a few days before the Windows 7 release so I put the Toshiba aside and waited for the free Windows 7 upgrade disk, which just arrived.
Since I haven’t used the Toshiba yet, there’s no data or personal programs to protect. I don’t want to keep Vista, and of course I don’t want to keep all the bloatware. Currently, Vista is on the C disk; there is a recovery or backup partition (D); and E is free for data. The Toshiba did not come with a Vista restore disk so I will burn recovery disks with Vista before I install Windows 7.
Like everyone, I want a fresh, clean sparkling brand-new install of Windows 7. I can follow the tutorials to boot from the Windows 7 upgrade disk, go to advanced tools and re-format the partition with Vista (i.e. C) and then install Windows 7. I should have no problem with registration or activation since Windows 7 will see Vista before it’s deleted. I’m not 100% clear whether the recovery partition (D) will be maintained but it shouldn’t matter much because I’ve got recovery disks … right?
My two questions:
1) Do I need to worry about losing my drivers in this scenario? Should I be taking a copy of all drivers ahead of time, and if so, is there somewhere (on the Toshiba) I can easily find them all? Or will they all be on the recovery disks I burn, should I need them?
2) What about the one or two Toshiba-specific programs I might want to keep, like Config-free and facial recognition software? Are they gone with the clean install, or can I also get them off the recovery disks (or recovery partition, if it still exists post-clean install)?
Is there anything else I need to know before I get started?? I’d like to make this as painless as possible ..
i want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7
View 4 Replies View RelatedI recieved a HP G62 340US about a year ago. A couple months back, around christmas, the computer stopped booting. It hung at the windows 7 starting screen. I ran a test and the long dst failed. I bought a new seagate 500Gb hard drive and reinstalled windows 7 (from the recovery disks that I had to buy). My computer has been working fine since about a week ago. When I opened Firefox or wordpad, I would get a BSOD. I found out it was a problem with my fonts folder. If I try to open the fonts folder, I get another BSOD. Then today I opened Photoshop and another BSOD. When my computer restarted, It said hard drive failure is immenent, then I preformed hard drive diagnostics. SMART passed, short dst passed, and long dst failed. Last week when I preformed the test, everything passed. I am worried that my hard drive will die again soon. Could it be that the hard drive is corrupted where the font folder is?
Failure ID:QC7VBS-5LI6H6-XXD0141-61DJ03
Product ID:XH066UA#ABA
COMPUTER:
Windows 7 64 Bit Home
8 GB upgraded ram
My hdd is:
Seagate Momentus Thin ST500LT012 500GB 5400 RPM 2.5"
Should I include the dump for the bsod as well?
Being a laptop owner i was not happy to read this SSD laptop drives ‘slower than hard disks’
But are 40% more expensive
Solid-state drives (SSDs) are becoming a more frequent storage component in laptops, and are promoted as being faster and more energy-efficient than traditional spinning hard drives. But tests prove that such drives are actually slower than standard laptop hard disks.
Having issues with RAID0 array being detected by Windows7 Ultimate x64 as SCSI. Apparently these drivers are the 'default' drivers that install when the RAID array is initialized. There is no option at this point to install other drivers instead.Using DeviceManager, there is an option to 'update drivers', and regardless of the method chosen, even selecting the file for a previously-downloaded set of drivers, Windows7 always comes back with a message of "Windows has determined that the best drivers for your system are already installed". Considering that SCSI drivers are the OLDEST ones out there, and actual SCSI devices are becoming rarer and rarer, how is it that these drivers cannot be replaced with more current and more applicable drivers?
View 5 Replies View RelatedMy hard drive died a couple of days ago and I was wondering if the only way to get the operating system back onto a new one is to purchase a new copy? Kinda new to this so am unsure what to do since it didn't come with any sort of OS recovery cd when I bought it.
View 5 Replies View RelatedHOW TO FORMAT PC FROM PENDRIVE
View 2 Replies View Relatedin the past i had a seperate personal hd for my work laptop I would take my work HD out then install my personal drive in and it worked great. But now on new laptop there is a biosandhard drive can I still switch hard drives or will it not work or will my work know I swap. Them.
View 2 Replies View RelatedMy hard drive crashed and I am replacing it with a new one. Can I just install a fresh copy of windows 7 on acer aspire 4810t without having to do any upgrades? I cannot upgrade until windows 7 is installed first. Is that possible?
View 2 Replies View RelatedHow can I migrate files and settings from a failed vista laptop's hard drive to a new windows 7 laptop?
View 2 Replies View RelatedI have a Gateway computer that came preloaded with Windows 7.
I am replacing the internal hard drive and I am attempting to install the factory system recovery image from the system recovery disc that I made when I bought the computer. After installing the drive and booting up from the recovery disc, I go into full factory recovery but when I go in to the option to "restore to factory default" the option is grayed out. Do I need to format the drive first? How do I do this outside of windows?
as some of you may know ive had a buggerload of problems with my LaCie external HDD, which, slowly, was put down to a faulty drive controller. Having taken out the HDDs held within, ( 2 samsung 500GB HDDs )
ive attempted to get 1 of them working as an internal drive. Ive connected it to the power and sata cable, but when i boot i (perhaps obviously?) am not getting any connection whatsoever. is there something i need to do in bios or something to get it to work? what am i doing wrong? (because invariably i AM doing something wrong).
My pc had suddenly decided to not recognising any of my Sata drives. Win 7 32 bit, 4 gig ram, asus psn d motherboard,ati sapphire 1g pci card, 1 250g western digital Sata drive 1 x 1tb seagate hdd. Sata DVD drive
Yesterday my pc froze up while surfing the web, so reset it and that where the problems started
It only recognised one of the hdd then wouldn't boot got a bsod uncountable boot volume. So opened up the case to check if the cables where loose, nope, so decided to run a repair via the recovery console. Didnt detect my o/s at all ask me to install the correct drivers grrrrr. So stripped the pc down swapped the Sata cables to see if that was the problem, no joy at all would only find one Sata drive and DVD drive. Then it wouldnt recognise any of them, so swapped out the Sata DVD drive for an IDE drive. The booted up nothing bar the DVD drive. Have now come to a cross roads don't know what else's to try. Managed to boot via a USB drive with Linux and everything system wise, pcu, gpu etc works, but still no Sata drives.
Done some digging online and some ideas are not a big enough psu, faulty Sata cables, but swapped in an IDE hdd and nothing again.
I would like the good and bad about running your SATA drives in IDE and AHCI modes.
I have 3 drives. 1 SSD and 2 normal hard drives.
Does it even make a difference? I have an Esata bracket that I want to run in AHCI mode but how about the normal system and data drives? What is the best way to set up drives?
I have an HP g42-415dx laptop with Windows 7 64 bit and AMD Dual-Core Athlon II P340 which I would like to replace for a faster AMD Quad-Core Phenom II P960 from e-Bay.
View 4 Replies View RelatedI'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.
My questions are:
1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?
2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)
3. I intend to run XP mode, will AHCI mode pose any problems for this?
Just built a moderate spec gaming PC from scratch, and all has went according to plan except when I try to install Windows 7, my hard drive won't show up. My new motherboard doesn't have any IDE slots, but I only have an IDE hard drive. I am using a 'Pluscom Serial ATA PCI Adapter' to connect my hard drive to the computer as it has 1 IDE slot on it. I don't have a disc for drivers and don't know where to start. I am running Ubuntu on it at the moment so I can download any drivers I may need.
View 9 Replies View RelatedWhat critical issues should I be aware of in the event I would like to REPLACE W7 os with XP3 os on a new laptop with 64-bit / 2GB ram
View 1 Replies View RelatedI've been reading about issues with people having problems with their SSD's not being reconized by Windows 7 Ultimate.but my WD 600gig STAT III Raptor is listed as a SCSI as well. I assume the problem is with my Marvell Driver.I bought this 60gig OCZ Vertex 3 SATA III drive for a Boot drive and had a pain installing drivers for it on a clean install of windows. I plugged it, and my WD Raptor both into the 2 SATA III ports that I have on my ASUS Rampage III MB. I set the Drives to ACHI not IDE. Tried to install Windows, had to force windows to accept the Marvell Drivers...but finally got it installed.Now Im stuck with the OCZ SSD and the Raptor both at SCSI speeds...not able to get them reconized my Windows 7 Ult as SATA drives.Should I try uninstalling the Marvell and JBMicron drivers and let Windows try and install drivers that will work? Funny thing is, I know that windows is reconizing the SSD as a SSD because of the Disk Defrag has been disabled on it...and was able to get some info off the drive via Intels SSD toolbox....OCZ's tool box wont reconize it unless you use Windows drivers. I had to install the Marvell Drivers to install Windows, Windows wouldn't reconize either drive plugged into the SATA III ports.I've tried bout everything, even tried the reg. fix via the Windows Helper with no luck.
View 1 Replies View RelatedA strange problem, nothing critical, but I found it annoying that my optical sata drives will not boot from a bootable disk when in AHCI mode in Bios. If I switch the drive mode to native IDE then I can boot just fine from either of the Opitcal Sata drives.I have done some searching and found this has been a problem out for some builds/MB in the past but you would think with a new MB and Sata controller and such this would no longer be a problem.If you look at my specs you will see the Gigabyte MB. The documentation is fuzzy on the sata ports. There is a setting to put SATA port 4/5 into some kind of IDE support mode. I currently have the slots 0 - 3, used for all the drives. 0 & 1 for HDD, and 2 & 3 for the optical drives,wondering if I use the 4/5 slots for the SATA and set the bios to the 4/5 ide support if this might solve my little problem.
View 9 Replies View RelatedI updated the SATA AHCI controller from device manager and rebooted. Shortly after I noticed disk drives F:, Z:, and X: are gone. No big deal I'll just repartition right? No they aren't showing up in Disk Management? The driver I installed I got from gigabyte it was a preinstall driver for ahci. I just installed windows 7 64 yesterday to a Samsung 830 256gb and it was working fine maybe I shouldn't have messed with it. C: drive is working fine just the other 3. Should I roll the driver back? System restore? Did I install the wrong driver?
View 3 Replies View RelatedI have a burnt up motherboard in my laptop. My question is do I have to match the exact model to the one that is in there already inside? Or can I get one alittle cheaper? The one that is inside is around $200, and I was hoping to spend a bit less.Me and hubby can replace and change out anything on a desktop, and even build one from scratch.But laptops aren't our thing.This one is an ASUS K52F REV 2.0. Any suggestions, or do I have to match it up with what is factory?
View 2 Replies View RelatedI need to replace my wireless adapter in my laptop. My current card is an Intel Wifi link 5100 agn, which is a PCI express half mini card.How can I tell which replacement card will be compatible? My computer is: Dell Studio 1555 Windows 7 Home Premium x64
View 8 Replies View RelatedI am using a asus laptop and have recently installed the Windows 7 . I was using the Windows xp before, and did not have any issues with the battery, but now the battery symbol in the notification bar is crossed out and the exact error message is that "[t]here is a problem with your battery, so your computer might shut down suddenly". The battery I am using is quite old, so it may in fact need to be replaced, but as far as I can tell it is functioning properly..
View 2 Replies View RelatedSo recently my desktop PC has been freezing at random times, and then sometimes restarting after not responding for a couple of minutes (no BSOD, just restarts as far as I've seen). It sometime freezes as soon as I turn the computer on, while Windows is loading, and sometimes it will start freezing after an hour it's been on. Most of the time it will just freeze for around a minute, and then unfreeze, but sometimes it does freeze and then restart. By freeze I mean everything, mouse included, and ctrl+alt+delete doesn't work.Also at bootup sometimes, it will fail to detect my SATA hard-drive and hang at Detecting SATA drives at the bios screen. This will be following by a disk read error.This problem started occuring a couple of weeks a go, so I reinstalled Windows 7 and it worked fine after that.
Running Windows 7
Bios: Phoenix - AwardBios v6.00PG
Processor: Intel Core2 Duo CPU E6550 @2.33GHz
2GB RAM
Graphics Card: Nvidia GeForce 8600 GS