Replacing SCSI Storage Drivers With IDE Or SATA Drivers?
May 18, 2012
Having issues with RAID0 array being detected by Windows7 Ultimate x64 as SCSI. Apparently these drivers are the 'default' drivers that install when the RAID array is initialized. There is no option at this point to install other drivers instead.Using DeviceManager, there is an option to 'update drivers', and regardless of the method chosen, even selecting the file for a previously-downloaded set of drivers, Windows7 always comes back with a message of "Windows has determined that the best drivers for your system are already installed". Considering that SCSI drivers are the OLDEST ones out there, and actual SCSI devices are becoming rarer and rarer, how is it that these drivers cannot be replaced with more current and more applicable drivers?
I have a Dell XPS730 with the Nvidia Nforce 790i chipset. I run two 500 gig SATA drives under RAID 0. I recently installed an Intel X25 80 gig SSD and have ran into problems. Windows recognizes the drive as SCSI in device manager. Granted it works however because it is listed as SCSI TRIM and the intel toolbox wont work which makes an SSD useless.After tons of research I have found that because of the Nvidia chipset it makes the drive show up as SCSI. I have tried Vista and Windows 7, both show it as SCSI. I have moved the SATA cable away from the other main 4 that support RAID with no luck. I have refomatted several times as well with no luck. I have completely disabled RAID in the bios and it STILL shows as SCSI. Is there any way to get around this? I have read that changing the nvidia controller drivers may work but im not sure what I would switch them to?
I have a lsi megaraid 1600 elite scsi card which is not being dected by windows 7 64bit. I have tried several drivers packages for server 2003 and 2008 but it doesnt work. Lsi does not list visa drivers for this card on thier site. Does anyone have any suggestions.
I've been reading about issues with people having problems with their SSD's not being reconized by Windows 7 Ultimate.but my WD 600gig STAT III Raptor is listed as a SCSI as well. I assume the problem is with my Marvell Driver.I bought this 60gig OCZ Vertex 3 SATA III drive for a Boot drive and had a pain installing drivers for it on a clean install of windows. I plugged it, and my WD Raptor both into the 2 SATA III ports that I have on my ASUS Rampage III MB. I set the Drives to ACHI not IDE. Tried to install Windows, had to force windows to accept the Marvell Drivers...but finally got it installed.Now Im stuck with the OCZ SSD and the Raptor both at SCSI speeds...not able to get them reconized my Windows 7 Ult as SATA drives.Should I try uninstalling the Marvell and JBMicron drivers and let Windows try and install drivers that will work? Funny thing is, I know that windows is reconizing the SSD as a SSD because of the Disk Defrag has been disabled on it...and was able to get some info off the drive via Intels SSD toolbox....OCZ's tool box wont reconize it unless you use Windows drivers. I had to install the Marvell Drivers to install Windows, Windows wouldn't reconize either drive plugged into the SATA III ports.I've tried bout everything, even tried the reg. fix via the Windows Helper with no luck.
Just installed Windows 7 RTM and my Sata HDD's and DVDRW are reporting as SCSI devices. I would get this problem in XP if I installed the mobo's raid drivers by accident. If I did then the devices would report as SCSI and the dvd burner would report as a cdrom and would not burn or read dvds
Whereas in Windows 7 the burner is reporting as a DVDRW scsi CDrom and will play dvd's and burn them too.
So at the moment there doesn't seem to be any problem however whilst navigating through the control panel I noticed the WEI. So I took a look and it's report my primary hard drive with a score of 5.9. The hard drive is a brand new Western Digital Caviar Black 500gb 32mb cache disk, is this score normal for such a drive?
Also is there anything else to worry about with the devices reporting as SCSI or is okay to leave it like that.
I upgraded my dell studio 1535 from Vista 64 bit to 7 professional 64-bit and now have problems with the keyboard (It's usually recognized, but keystrokes are often not recorded. Sometimes it doesn't work at all). USB devices work fine. I have my Vista OS under c:Windows.old so I would like to replace the 7 keyboard drivers (i8042prt.sys and kbdclass.sys) with the Vista drivers of the same names that are in c:window.oldwindowssystem32drivers Will this cause any problems? If not, how would I go about doing this?
I have a brand new Toshiba laptop with Vista. It arrived just a few days before the Windows 7 release so I put the Toshiba aside and waited for the free Windows 7 upgrade disk, which just arrived.
Since I haven’t used the Toshiba yet, there’s no data or personal programs to protect. I don’t want to keep Vista, and of course I don’t want to keep all the bloatware. Currently, Vista is on the C disk; there is a recovery or backup partition (D); and E is free for data. The Toshiba did not come with a Vista restore disk so I will burn recovery disks with Vista before I install Windows 7.
Like everyone, I want a fresh, clean sparkling brand-new install of Windows 7. I can follow the tutorials to boot from the Windows 7 upgrade disk, go to advanced tools and re-format the partition with Vista (i.e. C) and then install Windows 7. I should have no problem with registration or activation since Windows 7 will see Vista before it’s deleted. I’m not 100% clear whether the recovery partition (D) will be maintained but it shouldn’t matter much because I’ve got recovery disks … right?
My two questions:
1) Do I need to worry about losing my drivers in this scenario? Should I be taking a copy of all drivers ahead of time, and if so, is there somewhere (on the Toshiba) I can easily find them all? Or will they all be on the recovery disks I burn, should I need them?
2) What about the one or two Toshiba-specific programs I might want to keep, like Config-free and facial recognition software? Are they gone with the clean install, or can I also get them off the recovery disks (or recovery partition, if it still exists post-clean install)?
Is there anything else I need to know before I get started?? I’d like to make this as painless as possible ..
I want to put my old hard drive that has files and was used with windows vista and put it into a new windows 7 laptop. Is there any overlap or any config problems I can run into doing this? Or do I just put it in and the old files should work and all i have to do is update some drivers from vista to 7?
I'm getting ready to remove Windows 7 RC and install my legit copy of Windows 7 on my PC. My version of Windows 7 is a XP Pro -> Windows 7 Pro upgrade. When I did this upgrade on my laptop, I ran into a bunch of SATA issues because Windows XP does not support SATA on the default installation disk. Needless to say, a few hours later of messing with nLite, my laptop is good to go.
I want to avoid this mess with my PC and already be prepared. I'm trying to figure out what SATA drivers I need to use with nLite for my main PC. Is there somewhere I can go to get this information? Are the drivers based off my motherboard? CPU? Hard drive? Not sure where to start. My laptop's SATA drivers seemed to be based off the CPU (AMD) going by the name of the driver file.
I am installing Windows 7 on my Compaq Presario SR5010NX. SATA hard drives and IDE hard drives both detect and are visible in Setup (BIOS) as well as in my existing Windows 7 which is on a small 37 Gb SATA. When I try to install Windows 7 onto a new SATA hard drive 1.0T it wont show up in the window to select it for installation. The next window says to brows to the device driver to install it in the system. It describes the needed driver as a 'Mass Storage Controller Driver' which I cannot find anywhere. WTF do I do ?
I want to dual boot Win XP and and Win 7 and I need my SATA drivers. I've been searching the internet and the ASUS website but I can't find the SATA drivers.I have an ASUS G73JH. I can't find my MoBo model. I used everest but it says unknown motherboard. My hard drive is a Seagate Momentus St9500420as.
the board is DFI lanparty DK P45-T2RS PLUS, i'm trying to install the sata driver, but i have no idea which of the controller i need to update driver for:
Am expecting to receive my copy of Win 7 tomorrow, have got my drivers ready but am wondering whether there is an issue with installing Win 7 onto a SATA drive.
Had issues when installing XP as it wouldn't recognise the SATA drive and wouldn't load the drivers either. Ended up making a slipstream disk with the drivers on which took a while to get right.
Does Win 7 install onto a SATA drive straight out of the box or will I have the same problems as I had with XP?
I am trying to install Windows 7 on a system I just built and it tells me that it cannot be installed to my hard drive because it is "of the GPT partition style" and that "the partition is of an unrecognized type". What does this mean and how can I resolve it?The motherboard is intel DH55TC and the hard drive is Western Digital SATA 500GB.
My dads laptop has suddenly stopped recognizing any type of usb device properly that has not been used before. This includes 2 memory sticks and a 250gb Hdd. What happens is the devices are visible in the device manager, However they are not being recognised as Usb mass storage devices and are "Unknown". Windows update fails to find the drivers for them despite the fact when plugged into my pc it finds them instantly.
I have an adaptec sata controller card, which I was contemplating using for running my two raid drives.
I know that there are Vista 64 drivers availiable to download, and so my question is this,
will Vista 64 disk drivers work with Windows 7 Beta build 7000?
I thought i'd ask here first, as it seems silly to reformat and save disc images, reinstall etc, if someone here already knows the answer.
Also, is there a simple way transferring all the user's data and programme data if I wanted to upgrade to a newer build, as obviously backing up the disc image won't work I suppose with a newer build of 7?
my computer was working fine, but then I goto boot up today and it doesn't even recognize my Hard drive. I'm running windows 7 ultimate, 64bit.The computer won't even boot, my bios boot priorities are set as default.
I really want to go back to a dual install (Windows 7-64 Pro and Windows XP) but I want to add XP to Windows 7 which is already loaded. I know how to load Sata drivers when loading XP first (have drivers on CD) but after looking at the tutorial it mentions adding Sata drivers to XP using 3.5 disk. I do not have 3.5 drive. HP Pavilion a6130n/3 internal 1TB drives. XP and 7 will be on separate hard drives.
i have an alienware d900 i bought a 1TB samsung sata HDD but it does not detect the HDD with any of the windows operating system. it does not have driver for window 7 but it come with drivers for window xp and 2000 but when i try to install window xp i press f6 to load third party drivers then when is loading it gives me the option then i chose xp then it loads but it still dose not detect the hard drive.
I am using an Asus x58 P6TDeluxe and running Windows 7 x64 OEM. I have tried installing the chipset driver and intel matrix storage manager driver (to get SAS working) but both say "Does not support this operating system WNT_6.0P_64_MCE" and "This computer does not meet the minimum requirements for installing this software. Setup will exit".
I have an Abit NF7-S mobo (5+ yrs old) that has an nForce2 Ultra 400 + MCP-T chipset. The nvidia site has classified this as legacy, and only has the download for Vista.
Well I usually prefer to install the 'official' drivers, as MS ones seem to be at times problematic from experience. However I went along with installing the ones provided my microsoft update. All components in Device Manager seem to have been installed, and the OS is working without a problem.
But the voice within me still prefers the 'official' vendor software. Would the vista one provided by nvidia work on Windows 7. I use to get a nice small app to control audio in the official release, which I am obviously not getting in the MS trimmed version.
I also have a SATA 150 RAID (Silicon Image Sil 3112A SATA PCI Controller) on the NF7-S which has the same issue as above. All working.. but for that voice.
