Am expecting to receive my copy of Win 7 tomorrow, have got my drivers ready but am wondering whether there is an issue with installing Win 7 onto a SATA drive.
Had issues when installing XP as it wouldn't recognise the SATA drive and wouldn't load the drivers either. Ended up making a slipstream disk with the drivers on which took a while to get right.
Does Win 7 install onto a SATA drive straight out of the box or will I have the same problems as I had with XP?
One question I have is are the device drivers included on the windows 7 disc? I'm not sure I have a device driver disc let alone knowing what drivers I need.
Having issues with RAID0 array being detected by Windows7 Ultimate x64 as SCSI. Apparently these drivers are the 'default' drivers that install when the RAID array is initialized. There is no option at this point to install other drivers instead.Using DeviceManager, there is an option to 'update drivers', and regardless of the method chosen, even selecting the file for a previously-downloaded set of drivers, Windows7 always comes back with a message of "Windows has determined that the best drivers for your system are already installed". Considering that SCSI drivers are the OLDEST ones out there, and actual SCSI devices are becoming rarer and rarer, how is it that these drivers cannot be replaced with more current and more applicable drivers?
I'm getting ready to remove Windows 7 RC and install my legit copy of Windows 7 on my PC. My version of Windows 7 is a XP Pro -> Windows 7 Pro upgrade. When I did this upgrade on my laptop, I ran into a bunch of SATA issues because Windows XP does not support SATA on the default installation disk. Needless to say, a few hours later of messing with nLite, my laptop is good to go.
I want to avoid this mess with my PC and already be prepared. I'm trying to figure out what SATA drivers I need to use with nLite for my main PC. Is there somewhere I can go to get this information? Are the drivers based off my motherboard? CPU? Hard drive? Not sure where to start. My laptop's SATA drivers seemed to be based off the CPU (AMD) going by the name of the driver file.
I want to dual boot Win XP and and Win 7 and I need my SATA drivers. I've been searching the internet and the ASUS website but I can't find the SATA drivers.I have an ASUS G73JH. I can't find my MoBo model. I used everest but it says unknown motherboard. My hard drive is a Seagate Momentus St9500420as.
the board is DFI lanparty DK P45-T2RS PLUS, i'm trying to install the sata driver, but i have no idea which of the controller i need to update driver for:
I am trying to install Windows 7 on a system I just built and it tells me that it cannot be installed to my hard drive because it is "of the GPT partition style" and that "the partition is of an unrecognized type". What does this mean and how can I resolve it?The motherboard is intel DH55TC and the hard drive is Western Digital SATA 500GB.
I have an adaptec sata controller card, which I was contemplating using for running my two raid drives.
I know that there are Vista 64 drivers availiable to download, and so my question is this,
will Vista 64 disk drivers work with Windows 7 Beta build 7000?
I thought i'd ask here first, as it seems silly to reformat and save disc images, reinstall etc, if someone here already knows the answer.
Also, is there a simple way transferring all the user's data and programme data if I wanted to upgrade to a newer build, as obviously backing up the disc image won't work I suppose with a newer build of 7?
my computer was working fine, but then I goto boot up today and it doesn't even recognize my Hard drive. I'm running windows 7 ultimate, 64bit.The computer won't even boot, my bios boot priorities are set as default.
I really want to go back to a dual install (Windows 7-64 Pro and Windows XP) but I want to add XP to Windows 7 which is already loaded. I know how to load Sata drivers when loading XP first (have drivers on CD) but after looking at the tutorial it mentions adding Sata drivers to XP using 3.5 disk. I do not have 3.5 drive. HP Pavilion a6130n/3 internal 1TB drives. XP and 7 will be on separate hard drives.
i have an alienware d900 i bought a 1TB samsung sata HDD but it does not detect the HDD with any of the windows operating system. it does not have driver for window 7 but it come with drivers for window xp and 2000 but when i try to install window xp i press f6 to load third party drivers then when is loading it gives me the option then i chose xp then it loads but it still dose not detect the hard drive.
I have an Abit NF7-S mobo (5+ yrs old) that has an nForce2 Ultra 400 + MCP-T chipset. The nvidia site has classified this as legacy, and only has the download for Vista.
Well I usually prefer to install the 'official' drivers, as MS ones seem to be at times problematic from experience. However I went along with installing the ones provided my microsoft update. All components in Device Manager seem to have been installed, and the OS is working without a problem.
But the voice within me still prefers the 'official' vendor software. Would the vista one provided by nvidia work on Windows 7. I use to get a nice small app to control audio in the official release, which I am obviously not getting in the MS trimmed version.
I also have a SATA 150 RAID (Silicon Image Sil 3112A SATA PCI Controller) on the NF7-S which has the same issue as above. All working.. but for that voice.
I had to do a fresh reinstall today and I wanted to know if I should download and install any of the drivers (other than Ethernet LAN to get me online) for my comp'?In particular, the SATA drivers for a 64-bit install http://ca.gigabyte.com/products/pr [...] l=1#driver,I do have to install the audio and video, but otherwise, not sure about the SATA.
I recently build a new system with win7 64bit. Everything went well untill I exchanged a blue ray drive with a dvdwriter (1 day later). Win7 recognized the drive in device manager but did not assign a drive letter nor would the drive open (function). After trying everything I can think of I decided to reinstall the sata drivers from the asus websitebecause I wasn't able to use the motherboard disk with the DVD drive for installation) the system restarted and never booted back up. The bios recognize the ssd as 1st boot but win7 does not boot back up. As a matter of fact the hd LED doesnt flash anymore like it did when the system was working. I also could not use 5 USB ports (i was going to reinstall the drivers after the sata drivers) from the beginning of win7 install and Bluetooth comport not available. Did I screw up the bios? (bios flash with USB?)
Win7 Asus rampage iv extreme x79 2x2gb corsair dominator gt 1600 Intel i7 3820 Sandisk extreme ssd 120gb (the only storage media) Corsair h100 cooling
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?
i am havin pci to sata port card and i need drivers or how to configure with Intel DG41WV motherboard, if i installed this card in PCI bus it is not showing drive in OS windows 7 64 bit
Windows 7 64bit Pro SP1 OEM System Builder Pack Gigabyte H77M-D3H 1TB SATA HDD WD Caviar Black Intel Core i3 2125 DDR3 8GB 1600 Intel Viper SATA LG Blue Ray DVDRW
Clean install of Windows reveals an error not detecting any drives, does not allow partitioning or formatting. BIOS identifies the drives.I've attempted installs of updated drivers from the motherboard's website (as well as the CD that came with the motherboard). WD claims not to have any drivers on their website. Still nothing.