How to load Windows 7 on scsi raid systems? the drives aint recognise i had to load sata drivers for my portege laptop m400 what drivers do i need? raid or scsi from dell? poweredge 1800/2800
View 6 Replies
How can I uninstall a Gigabyte raid contoller without crashing my Win 7 OS? Uninstall is being prevented because "the OS is on the contoller"! Win 7 64 bit is on a Crucial SSD boot drive and AHCI is set in BIOS. However the raid controller is setting all internal drives to SCSI!
View 1 Replies View RelatedI am currently attempting to install Windows 7 on an SSD RAID Array, and I have encountered several issues (this has been a one step forward, two steps backward affair). The issue that I am currently facing is the fact that I am unable to load RAID drivers during the OS installation.As is normal for this kind of installation I choose "Custom" and I cannot see any drives listed, this is the point at which I click on "Load Drivers" and then I select "Browse". My challenge is that regardless of how I "insert the drivers", which is to say whether I put them on a separate USB drive (FAT32 partitioned), or take the Windows 7 installation DVD out and insert a CD with drivers - I simply cannot navigate to the drivers.Because I am unable to load the RAID drivers I simply cannot proceed with the OS installation.*** Note ****As of writing this I came across a program called RT Seven Lite, which has allowed me to create a "slip streamed" Windows 7 installation - using the program I was able to integrate the troublesome drivers into the Windows 7 installation disk.
View -1 Replies View RelatedI am currently attempting to install Windows 7 on an SSD RAID Array, and I have encountered several issues (this has been a one step forward, two steps backward affair). The issue that I am currently facing is the fact that I am unable to load RAID drivers during the OS installation.
As is normal for this kind of installation I choose "Custom" and I cannot see any drives listed, this is the point at which I click on "Load Drivers" and then I select "Browse". My challenge is that regardless of how I "insert the drivers", which is to say whether I put them on a separate USB drive (FAT32 partitioned), or take the Windows 7 installation DVD out and insert a CD with drivers - I simply cannot navigate to the drivers.
Because I am unable to load the RAID drivers I simply cannot proceed with the OS installation.
As of writing this I came across a program called RT Seven Lite, which has allowed me to create a "slip streamed" Windows 7 installation - using the program I was able to integrate the troublesome drivers into the Windows 7 installation disk.
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
View 1 Replies View RelatedHaving gone through all the setting up processes, my system will not produce Minidump Files, an SCSI miniport is mentioned as part of the production process, yet I have searched my system and cannot find one.
View 2 Replies View RelatedI have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
Can W/7 install to a SCSI drive without the driver installation (F6)? I'm just about to install W7, and it seems to detect all 3 SCSI drives without the driver for the LSI 1030 Ultra SCSI adapter.
I'm just a little surprised how simple this is, usually you have to supply the additional driver...
I've been reading about issues with people having problems with their SSD's not being reconized by Windows 7 Ultimate.but my WD 600gig STAT III Raptor is listed as a SCSI as well. I assume the problem is with my Marvell Driver.I bought this 60gig OCZ Vertex 3 SATA III drive for a Boot drive and had a pain installing drivers for it on a clean install of windows. I plugged it, and my WD Raptor both into the 2 SATA III ports that I have on my ASUS Rampage III MB. I set the Drives to ACHI not IDE. Tried to install Windows, had to force windows to accept the Marvell Drivers...but finally got it installed.Now Im stuck with the OCZ SSD and the Raptor both at SCSI speeds...not able to get them reconized my Windows 7 Ult as SATA drives.Should I try uninstalling the Marvell and JBMicron drivers and let Windows try and install drivers that will work? Funny thing is, I know that windows is reconizing the SSD as a SSD because of the Disk Defrag has been disabled on it...and was able to get some info off the drive via Intels SSD toolbox....OCZ's tool box wont reconize it unless you use Windows drivers. I had to install the Marvell Drivers to install Windows, Windows wouldn't reconize either drive plugged into the SATA III ports.I've tried bout everything, even tried the reg. fix via the Windows Helper with no luck.
View 1 Replies View RelatedI have Win 7 Pro 64 bit installed on an ASUS P7P55D LE motherboard which supports RAID 0,1,5 and 10 using Intel Matrix Storage Technology through an on board Intel P55 chip set. The system was assembled in Nov 2009 using two Western Digital Caviar Black 750Gb drives in RAID 1 as Drive C:. (I now know from Western Digital Customer Service that I shouldnt have done that, but lets move on from there). Last December, an error message informed me the RAID array was broken and identified one of the 750 Mb drives as needing replacement. I happened to have a spare 1.5Tb WD Caviar Black at the time, so I pulled the 750Mb drive and replaced it with the 1.5Tb drive. Life was once again good. Then on July 4th (wouldnt you know) there was a repeat of the December 2011 error message telling me to replace the other original 750Gb drive. Okay so I had another 1.5Tb WD Caviar Black laying around (dont ask) and did a similar swap out. Thats when I emailed WD Customer Support asking about the 750 since their diagnostic software said the drives were fine. Thats when I learned that I should be paying lots more for enterprise quality drives if I want/need RAID. Well thats not what ASUS says in their advertising, but live and learn. All thats prologue, because my real question is whether its possible to break the hardware-based RAID 1 array and set up a Windows 7-based RAID 1 with the two 1.5Tb WD Caviar Black drives without having to reinstall Windows 7.
View 1 Replies View RelatedI need a PCI SATA 6 RAID card that has at least 4 slots for 4 X 2TB Hard drives for a RAID 5
View 3 Replies View RelatedI had one hard drive failed(640gb). I bought replacement and tried to restore image but it failed. Then I wanted to convert to non raid system. I changed both drives(640gb) to non raid and bios change in advance setup. I am getting error when I try to reinstall win 7, "setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information". I have deleted old partition many times but win 7 setup on this dell xps435 desktop won't install windows.
View 4 Replies View RelatedI am trying to install drivers for an Adaptec AHA-2940 SCSI card.
The adaptec website there is no 64 bit version available, but i have been reading around for solutions with no success.
I need the "Adaptec AIC-7870 PCI SCSI Controller" ... but there is no 64 bit version for that. When i try to install the drivers (there is no installer program, i just need to use the update drivers feature of windows) it says that it is not a 64 bit version so i can't use it.
Is there any solution to my problem?
Prior to purchasing a Vista Ultimate to Windows 7 Ultimate upgrade for $220, I downloaded and ran the compatibility/upgrade adviser program and found no problems.While running the Windows 7 Install disk, the installation stopped dead with the message that I must update the driver for my Adaptec 29160N SCSI hard disk storage controller. However it could not find a newer driver than the one I am currently using under Vista, version 6.5.645.100, dated 1/31/2007.
View 4 Replies View RelatedI have a couple of old SCSI slide scanners and SCSI cards I use in (real) 32-bit XP, that no 64 bit drivers exist for. So I haven't been able to get them to work in Windows 7.
Is there any hope of getting them to work via Windows XP Mode in Windows 7? My impression scanning posts here is that this won't work, as I need real XP to talk to real SCSI cards with real drivers, and the virtual/emulated environment won't acommodate this.
I picked up a VT capable processor, hoping to try all this out, but now I find my Windows 7 RC eval setup can't load the RTM Windows XP Mode and Virtual PC software, so I'm unable to test it out. No way I'm springing for Windows 7 Pro only to find out the virtualization capability won't do what I need it to do.
Will I have to continue to dual-boot into XP when I want to work with the old hardware? If so, I'll just get the Windows 7 Home family pack, and forget about VT..
Anyone have working driver for this scsi card, i like this, and this can working good for my Umax 1220s flatbed scanner
View 0 Replies View RelatedI have a Dell XPS730 with the Nvidia Nforce 790i chipset. I run two 500 gig SATA drives under RAID 0. I recently installed an Intel X25 80 gig SSD and have ran into problems. Windows recognizes the drive as SCSI in device manager. Granted it works however because it is listed as SCSI TRIM and the intel toolbox wont work which makes an SSD useless.After tons of research I have found that because of the Nvidia chipset it makes the drive show up as SCSI. I have tried Vista and Windows 7, both show it as SCSI. I have moved the SATA cable away from the other main 4 that support RAID with no luck. I have refomatted several times as well with no luck. I have completely disabled RAID in the bios and it STILL shows as SCSI. Is there any way to get around this? I have read that changing the nvidia controller drivers may work but im not sure what I would switch them to?
View 9 Replies View Relatedi need windows 7 32-bit drivers dell inspiron
View 3 Replies View RelatedWhich configuration would be better using mobo sats 2 raid or using seperate rid controller via pcie card Rosewill Rc-211 wsis3132) or should I use mobo for raid and card for extra sata w/o raid I have more drives than sata slots. How do I transfer data videos/Tv shows from existing drive to raid?
View 1 Replies View RelatedI am trying to install Windows 7 on my test machine. However, I can't get it to detect any drives - three are 3 disks in the system - it is an IDE disk. When I try and install, it can't detect any disks, but when I try and install through Windows Vista, it detects them.
However, then it says it needs the driver for the LSI Logic 22910, 21002 PCI SCSI adapter; 53C896 Device. Is there still a version of this, and if so, where can I get it? I have tried everywhere I can think of, including the LSI website!
I have a lsi megaraid 1600 elite scsi card which is not being dected by windows 7 64bit. I have tried several drivers packages for server 2003 and 2008 but it doesnt work. Lsi does not list visa drivers for this card on thier site. Does anyone have any suggestions.
View 6 Replies View RelatedJust installed Windows 7 RTM and my Sata HDD's and DVDRW are reporting as SCSI devices. I would get this problem in XP if I installed the mobo's raid drivers by accident. If I did then the devices would report as SCSI and the dvd burner would report as a cdrom and would not burn or read dvds
Whereas in Windows 7 the burner is reporting as a DVDRW scsi CDrom and will play dvd's and burn them too.
So at the moment there doesn't seem to be any problem however whilst navigating through the control panel I noticed the WEI. So I took a look and it's report my primary hard drive with a score of 5.9. The hard drive is a brand new Western Digital Caviar Black 500gb 32mb cache disk, is this score normal for such a drive?
Also is there anything else to worry about with the devices reporting as SCSI or is okay to leave it like that.
I've spent the last couple of days trying desperately to resolve this issue. I have looked everywhere but cannot find an answer... PROBLEM: I have thousands of PDFs in hundreds of folders. When I go to a particular folder, I use the slider to change the Explorer views from "Content" to "Extra Large Icons" but cannot get a thumbnail preview of the PDFs - all I see is an Acrobat Icon preview.I know that this is an issue on the X64-bit verson of Windows 7, but I'm running 32-bit Windows 7 (Ultimate)! ATTEMPTS: I've tried several ways to resolve this but nothing worked so far. Specifically, I: 1. Made sure that the File Type Associations are correct.2.Unchecked Folder options>View>"Always show icons, never thumbnails".3. Made sure that Folder options>View> "Display file icon on thumbnails" is checked.4.Made sure that Performance>Settings>"Show thumbnails instead of icons" is checked.5. Tried the simple method suggessted at other forums: going into Adobe and opening the directory to preview the files as thumbnails from there and then refreshing the folder in Windows Explorer to display a thumbnail preview of the PDF file - Didn't work either!6. Ran "Repair Acrobat Installation".7. Uninstalled and Reinstalled Acrobat 9 (including associated registry files).8. Installed the latest version of Reader.9. Tried installing other software (PDF-XChange and Foxit) but these don't create PDF thumbnails in Windows Explorer either.
View 9 Replies View RelatedI had a ZT Systems I-7 920 computer that was stolen when my house was robbed. It came with a Windows 7 disk that says it can only be used with the ZT Systems computer (that was stolen). I am now building a new computer and I am wondering if I can use the Windows 7 disk from the ZT systems computer in my new computer. I paid for Windows 7 when I bought the ZT systems computer and I do not feel that I should have to buy it again.
View 8 Replies View RelatedI was wondering if i could use windows 7 on multiple systems? Im about to order the 64 bit edition for my current system but in 6-7 months ill be building a new system.could i use the same disc ?
View 16 Replies View RelatedIs there any difference in xp, vista and windows 7 operating systems regarding. control requests over control pipe.? we have developed drivers for ndis port miniport NDIS driver.its working fine with LTE network in XP and vista. but in case of windows 7 operating systems. when we send control request to stop network to device, we are not getting response from device. we have observed Lecroys usb analyzer logs. we are not getting response. even though we its device side problem. why this issue is not happening in xp and vista.we have two applications for sending control requests to device for starting network.
1) company application.
2) mobile broad band Microsoft provided default application .
this issue happens only with company application. we have compared data in requests send by cm and mobile broadband but no difference.
How do I get a camera wizard installed on my windows 7 systems?
View 1 Replies View RelatedI have both Windows 7 Home premium 64 and 32 bit installed on a split partition on my hard drive, but when I try go to boot, both editions just say: Windows 7. How do I change of the operating systems to boot to for the BCD File in Windows 7 so that perhaps one of them says Windows 7 32-bit while the other says Windows 7 64-bit. I know that in XP it is just a text file you have to edit, but in 7 it seems a bit more difficult.
View 1 Replies View RelatedI dont know if this is posted in the right area but I'm so desperate to get my laptop working its unreal. First it started off with my laptop crashing, I had totally forgot it needed to do a windows update and turned off my laptop in hopes that it would work properly. After that my laptop has not been working. The machine turns on and gives me two options. Start windows normally or do a repair. Upon starting windows normally, it loads so far before sending me back to the two options of start windows normally or repair. On the second time I clicked repair. My laptop then goes so far before presenting me with a blue screen that is usually the screen where my accounts are. The cursor still moves but it loads no further even after leaving it an hour. I decided to make a repair disk, hoping that the problem was because of windows. the disk loads, gives me a choice on the keyboard language then does nothing. I honestly have no idea what to do, I want to keep all the files safe on my computer as I havent backed them up and I have worked so hard on the projects.
View 1 Replies View Relatedanyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
I have two Dell All in one computers, one is a older 32 bit system and the newer one is 64 bit. Please tell me what the difference.
View 3 Replies View Related
